bulb CHERY TIGGO 2009 Service Repair Manual
[x] Cancel search | Manufacturer: CHERY, Model Year: 2009, Model line: TIGGO, Model: CHERY TIGGO 2009Pages: 1903, PDF Size: 33.38 MB
Page 1531 of 1903
Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
Available occupant restraints for this vehicle include both active and passive types. Active restraints are those which
require the vehicle occupants to take some action to employ, such as fastening a seat belt; while passive restraints
require no action by the vehicle occupants to be employed.
Active Restraints
•Front Seat Belts
• Rear Seat Belts
Passive Restraints
• Driver Airbag
• Passenger Airbag
• Seat Belt Tensioners
Operation
Active Restraints
The primary passenger restraints are the seat belts. Seat belts are referred to as an active restraint because the
vehicle occupants are required to physically fasten and properly adjust these restraints in order to benefit from them.
Passive Restraints
The passive restraints are referred to as a supplemental restraint system because they were designed and are
intended to enhance the protection for the occupants of the vehicle only when used in conjunction with the seat belts.
They are referred to as passive restraints because the vehicle occupants are not required to do anything to make
them operate; however, the vehicle occupants must be wearing their seat belts in order to obtain the maximum safety
benefit from the supplemental restraint system.
The supplemental restraint system electrical circuits are continuously monitored and controlled by a microprocessor
and software contained within the Restraints Control Module (RCM). An airbag indicator in the instrument cluster
illuminates for about seven seconds as a bulb test each time the ignition switch is turned to the ON or START posi-
tions. Following the bulb test, the airbag indicator is turned ON or OFF by the RCM to indicate the status of the
supplemental restraint system. If the airbag indicator comes ON at any time other than during the bulb test, it indi-
cates that there is a problem in the supplemental restraint system electrical circuits. Such a problem may cause
airbags not to deploy when required, or to deploy when not required.
Deployment of the supplemental restraints depends upon the angle and severity of an impact. When an impact is
severe enough, the microprocessor in the RCM signals the inflator of the appropriate airbag units to deploy their
airbag cushions. The front seat belt tensioners are provided with a deployment signal by the RCM in conjunction with
the front airbags.
Specifications
Torque Specifications
DESCRIPTION TORQUE (N·m)
Driver Side Airbag Retaining Bolts 10
Restraints Control Module Retaining Bolts 7-9
Front Passenger Side Airbag Retaining Bolts 10
14–2Chery Automobile Co., Ltd.
Page 1773 of 1903
Downloaded from www.Manualslib.com manuals search engine Front Combination Lamp Assembly
Removal & Installation
1. Open the hood.
2. Disconnect the turn signal lamp.
3. Disconnect the high/low beam front combinationlamp.
4. Remove the three front combination lamp assem- bly mounting bolts (1).
5. Carefully remove the front combination lamp assembly.
6. Installation is in the reverse order of removal.
1 Turn Signal Lamp
Bulb 12 V (21 W)
2 Headlamp Bulb
Front Position Lamp Bulb 12 V (55 W)
12V(5W)
EXTERIOR LAMPS
LTSM150037
LTSM150125
15
15–189Chery Automobile Co., Ltd.
Page 1775 of 1903
Downloaded from www.Manualslib.com manuals search engine 4. Disconnect the rear combination lamp.
5. Carefully remove the rear combination lamp assembly.
6. Installation is in the reverse order of removal.
Headlamp
Removal & Installation
1. Remove the front combination lamp assembly (See Front Combination Lamp Assembly Removal & Installation inSection 15 Body & Accessories).
2. Remove the headlamp bulb cover.
3. Disconnect the headlamp bulb electrical connector.
4. Remove the headlamp bulb clip.
1 Tail Lamp Bulb 12 V (21 W)
2 Backup Lamp
Bulb 12 V (21 W)
3 Rear Turn Signal
Lamp Bulb 12 V (21 W)
4 Stop Lamp Bulb 12 V (21 W)
EXTERIOR LAMPS
LTSM150126
15
15–191Chery Automobile Co., Ltd.
Page 1776 of 1903
Downloaded from www.Manualslib.com manuals search engine 5. Carefully remove the bulb (1) for the high/lowbeam headlamp.
6. Replace the bulb with a new bulb as needed.
7. Installation is in the reverse order of removal.
Front Fog Lamp
Removal & Installation
1. Remove the front bumper (See Front Bumper Removal & Installation in Section 15 Body &
Accessories).
2. Disconnect the fog lamp.
3. Remove three mounting nuts (1).
EXTERIOR LAMPS
LTSM150141
LTSM150038
15–192Chery Automobile Co., Ltd.
Page 1777 of 1903
Downloaded from www.Manualslib.com manuals search engine 4. Replace the bulb with a new bulb (1) as needed.
5. Installation is in the reverse order of removal.
Rear Fog Lamp
Removal & Installation
1. Remove the cover of the back cargo door.
2. Remove the rear fog lamp mounting screws (1).
3. Remove the rear fog lamp.
4. Disconnect the electrical connector for the rear foglamp.
5. Installation is in the reverse order of removal.
EXTERIOR LAMPS
LTSM150143
LTSM150082
15
15–193Chery Automobile Co., Ltd.
Page 1778 of 1903
Downloaded from www.Manualslib.com manuals search engine Tail/Backup/Stop Lamp
Removal & Installation
1. Open the plug cover of storage box at rear luggagecabin.
2. Use a trim stick and remove the internal protective cover (1).
3. Remove the bulbs for tail/backup/stop lamps by hand through the access hole.
4. Replace the bulb with a new bulb as needed.
5. Installation is in the reverse order of removal.
EXTERIOR LAMPS
LTSM150144
LTSM150146
15–194Chery Automobile Co., Ltd.
Page 1779 of 1903
Downloaded from www.Manualslib.com manuals search engine Turn Signal Lamp
Removal & Installation
1. Remove the front combination lamp (See Front Combination Lamp Removal & Installation in Section 15 Body &Accessories).
2. Replace the front turn signal lamp bulb (1).
3. Remove the rear combination lamp (See Rear Combination Lamp Removal & Installation in Section 15 Body & Accessories).
EXTERIOR LAMPS
LTSM150142
15
15–195Chery Automobile Co., Ltd.
Page 1780 of 1903
Downloaded from www.Manualslib.com manuals search engine 4. Replace the rear turn signal lamp bulb.
5. Hold the side turn signal lamp by hand and pullback and remove the lamp slowly.
6. Disconnect the side turn signal lamp connector (1).
7. Remove the side turn signal lamp assembly.
8. Replace the bulb with a new bulb as needed.
9. Installation is in the reverse order of removal.
EXTERIOR LAMPS
LTSM150146
LTSM150041
15–196Chery Automobile Co., Ltd.
Page 1781 of 1903
Downloaded from www.Manualslib.com manuals search engine High Mounted Stop Lamp
Removal & Installation
1. Remove the high mounted stop lamp cover (1).
2. Remove the high mounted stop lamp mountingscrews (2).
3. Disconnect the electrical connector (3) of the high mounted stop lamp.
4. Remove the high mounted stop lamp assembly.
5. Replace the bulb with a new bulb as needed.
6. Installation is in the reverse order of removal.
License Plate Lamp
Removal & Installation
1. Press the release tab with a flat screwdriver, remove the license plate lamp.
2. Disconnect the license plate lamp electrical connector.
EXTERIOR LAMPS
LTSM150124
LTSM150040
15
15–197Chery Automobile Co., Ltd.
Page 1782 of 1903
Downloaded from www.Manualslib.com manuals search engine 3. Replace the bulb with a new bulb (1) as needed.
4. Installation is in the reverse order of removal.
EXTERIOR LAMPS
LTSM150145
15–198Chery Automobile Co., Ltd.