fuel tank removal CHERY TIGGO 2009 Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine trols the frequency when the canister control valve operates in order to accommodate the vapor volume for each
cylinder.
Removal & Installation
1. Disconnect the battery negative cable.
2. Disconnect canister control solenoid valve electricalconnector.
3. Remove the canister control solenoid valve retain- ing bolt (1).
(Tighten: Canister control valve retaining bolt to 15
N·m)
4. Remove the canister control valve.
5. Installation is in the reverse order of removal.
Vapor Canister 1.6L & 1.8L & 2.0L
Description
The vapor canister is located on the left side of the core support and is filled with activated carbon granules.
Operation
The vapor canister is filled with activated carbon granules. Fuel tank vapors are vented into the canister where they
are absorbed by the activated carbon granules. The canister temporarily holds the fuel vapors until intake manifold
vacuum draws them into the cylinder chamber. The Engine Control Module (ECM) purges the canister through the
pulse-width modulated canister control valve. The ECM purges the canister at predetermined intervals and engine
conditions.
Removal & Installation
1. Raise and support the vehicle.
ON-VEHICLE SERVICE
LTSM030014
03
03–585Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2. Remove vapor canister retaining bolts (1).(Tighten: Vapor canister retaining bolt to 10 N·m)
3. Loosen the vapor canister hose.
4. Pull canister rearward to remove.
5. Installation is in the reverse order of removal.
Vapor Canister 2.4L
Description
The vapor canister is located on the left side of the core support and is filled with activated carbon granules.
Operation
The vapor canister is filled with activated carbon granules. Fuel tank vapors are vented into the canister where they
are absorbed by the activated carbon granules. The canister temporarily holds the fuel vapors until intake manifold
vacuum draws them into the cylinder chamber. The Engine Control Module (ECM) purges the canister through the
pulse-width modulated canister control valve. The ECM purges the canister at predetermined intervals and engine
conditions.
Removal & Installation
1. Raise and support the vehicle.
ON-VEHICLE SERVICE
LTSM030041
03–586Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2.4L
•Fuel pressure at idle: 320-350 kPa (3.2 - 3.5 bar)
3. If engine runs, but pressure is below minimum pressure, check the following: a. Check for a kinked fuel supply line between the fuel rail and the fuel pump, repair if necessary.
b. Check the fuel filter for blockage, and replace the fuel filter if necessary (See Fuel Filter Removal & Installa-
tion in Section 04 Fuel Delivery).
c. Check the fuel pump, and replace if necessary (See Fuel Pump Removal & Installation in Section 04 Fuel
Delivery).
4. If operating pressure is above the maximum pressure, the electric fuel pump is OK, but fuel pressure regulator is defective. Replace the fuel pressure regulator (See Fuel Pump Removal & Installation in Section 04 Fuel
Delivery).
NOTE:
• The 1.6L & 1.8L & 2.0L fuel pressure regulator is integrated into the fuel pump assembly and is not serviced
separately.
• The 2.4L fuel pressure regulator is connected to the fuel rail, and is serviced separately.
5. Install the protective cap to the service test port pressure fitting (1) on the fuel rail.
Observe the following fuel pressures when testing:
FUEL PRESSURE - 1.6L & 1.8L & 2.0L
Key On 400 kPa (4.0 bar)
Engine Idle 400-420 kPa (4.0 - 4.2 bar)
Key Off 380 kPa (3.8 bar) in 10 minutes
FUEL PRESSURE - 2.4L
Key On 329 kPa (3.29 bar)
Engine Idle 320-350 kPa (3.2 - 3.5 bar)
Key Off 350 kPa (3.5 bar) in 10 minutes
Fuel System Troubleshooting Chart
CONDITIONPOSSIBLE CAUSES CORRECTION
No Start/Hard Start/Start and then
Stall · Contaminated fuel
· Low fuel pressure
· Restricted fuel filter
· Fuel pump relay inoperative
· Restricted or leaking fuel lines
· Fuel pressure regulator· Drain, flush and refill fuel system.
· Check fuel pump pressure.
· Replace fuel filter.
· Test fuel pump relay.
· Inspect/replace necessary fuel
line(s), perform fuel system air
purge.
· Inspect/replace the fuel pump if
necessary.
Stalls Under Aggressive Maneuvers/
Loss Of Fuel Pressure · Restricted or damaged fuel filter
· Contaminated fuel
· Damaged fuel tank· Replace fuel filter.
· Drain, flush and refill fuel system.
· Replace fuel tank.
Cannot Refill Fuel Tank/Excessive
Pressure in Fuel Tank When Cap is
Removed · Sticking or damaged fuel tank
fill/vent valve, hose or lines.
· Inspect, repair vent hose and lines,
replace fuel tank.
DIAGNOSIS & TESTING
04
04–13Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Fuel Pressure Relief Procedure
Description
WARNING!
Fuel in the fuel system remains under high pressure, even when the engine is not running. Before servicing or
disconnecting any of the fuel lines or fuel system components, the fuel system pressure must be relieved to
prevent accidental spraying of fuel. Failure to follow these instructions may result in serious personal injury or
death.
Perform the following procedure to relieve fuel pressure from the fuel system:1. Remove the cover of the front fuse and relay box.
2. Identify and remove the fuel pump relay from the front fuse and relay box.
3. Start and run engine until it stalls.
4. Attempt to restart engine until it will no longer run.
5. Turn the ignition key to the OFF position.
Fuel Pump
Description
The fuel pump assembly contains the fuel pump motor and fuel level sensor.
Operation
The Engine Control Module (ECM) activates the fuel pump relay for several seconds after the ignition switch is
turned ON. When the relay is activated, it provides voltage to the fuel pump. When the ECM receives an engine
speed signal from the Crankshaft Position (CKP) sensor and a signal from the Immobilizer control module, the ECM
will energize the fuel pump relay.
NOTE :
• The electric fuel pump has different flow ratings based on engine requirements
• For service, the part number of the replacement fuel pump must be the equivalent of the original fuel pump
• Do not operate the fuel pump dry, this will damage the fuel pump
• Keep the fuel tank and pipeline clean, and replace the fuel filter if the fuel pump is replaced
Removal & Installation
WARNING!
Release fuel system pressure before servicing fuel system components. Service vehicles in well-ventilated areas
and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or death.
NOTE :
The following special tool is required to perform the repair procedure:
•CH-20032 - Fuel Pump Remover
1. Release the fuel system pressure (See Fuel Pressure Relief Procedure in Section 04 Fuel Delivery).
2. Disconnect the negative battery cable.
3. Remove the rear seat cushion.
04
04–15Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4. Remove the fuel pump cover (1).
5. Disconnect the fuel pump connector (3) and thefuel delivery hose (2) and fuel return hose (1).
6. Using special tool CH-20032, remove the fuel pump mounting cover (4).
7. Pull the fuel pump up and out of the fuel tank.
WARNING!
Do not smoke, carry lighted tobacco or have an open flame of any type when working on or near any fuel-
related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these
instructions may result in serious personal injury or death.
Do not carry personal electronic devices such as cell phones, pagers or audio equipment of any type when
working on or near any fuel-related component. Highly flammable mixtures are always present and may be
ignited. Failure to follow these instructions may result in serious personal injury or death.
When handling fuel, always observe fuel handling precautions and be prepared in the event of fuel spillage.
Spilled fuel may be ignited by hot vehicle components or other ignition sources. Failure to follow these instruc-
tions may result in serious personal injury or death.
NOTE :
Make sure not to spill fuel inside of the vehicle. 8. Tip the fuel pump on its side and drain the fuel from the fuel pump and remove the fuel pump from the vehicle. NOTE: To keep the fuel tank portion clean and to avoid damage and foreign materials, cover them completely
with plastic bags or something similar.
9. Remove and discard the seal from the fuel tank.
10. Installation is in the reverse order of removal.
Installation Notes:
• Install a new seal to the fuel pump sealing surface.
• Turn the ignition switch to ON (without starting the engine) to apply fuel pressure to the fuel system, then
check the connections for fuel leaks.
• Start the engine and let it idle and check for fuel leaks at the fuel system connections.
ON-VEHICLE SERVICE
LTSM040001
LTSM040002
04–16Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Fuel Pressure Regulator - With Mitsubishi 2.4L Engine
Description
The fuel pressure regulator is connected to the fuel rail. The fuel pressure regulator has a vacuum connection to it.
The fuel pressure regulator is used to regulate the fuel pressure in the fuel system.
NOTE :
The 2.4L is the ONLY engine that uses an external fuel pressure regulator.
Operation
The fuel pressure regulator is designed to keep the fuel pressure in the fuel system at a constant pressure. It does
this with a spring-loaded diaphragm that controls a valve. The valve, when opened by excessive pressure in the fuel
lines, uncovers a fuel line that returns excess fuel to the fuel tank. The vacuum connection is there to help reduce
emissions during deceleration. During deceleration, the vacuum connection serves to open the fuel return valve
wider, which reduces pressure in the system and prevents excess hydrocarbon emissions due to less fuel being
injected as a result of the lower pressure in the system.
Removal & Installation
WARNING!
Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas
and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or death.
1. Release the fuel system pressure (See Fuel Pressure Relief Procedure in Section 04 Fuel Delivery).
2. Disconnect the negative battery cable.
ON-VEHICLE SERVICE
LTSM040007
04
04–23Chery Automobile Co., Ltd.