oil viscosity CHEVROLET ASTRO PASSENGER 1994 1.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine Here are things some owners ask about. None of these indicate a problem
with your fuel gage:
0 At the gas station, the gas pump shuts off before the gage r\
eads full.
The fuel tank will take either a little more or a little less fuel to fill up
than the gage shows.
The gage moves a little when you turn a corner or speed up.
The gage doesn’t go back to empty when you turn off the ignition.
For your fuel tank capacity, see the Index under “Fluid Capacities.”
Oil Pressure Gage
Standard Cluster Digital Cluster
The oil pressure gage shows the engine oil pressure in psi (pounds pe\
r
square inch) when the engine is running. Canadian vehicles indicate
pressure in
kPa (kilopascals). Oil pressure may vary with engine speed,
outside temperature and oil viscosity, but readings above the low pressure
zone indicate the normal operating range.
A reading in the low pressure zone may be caused by a dangerous\
ly low oil
level or other problems causing low oil pressure.
On the digital cluster, a box around the oil pressure symbol \
will begin to
flash when the oil pressure
is low.
2-62

Downloaded from www.Manualslib.com manuals search engine You should also use the proper viscosity oil for your vehicle, as shown in
the following chart:
RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS
FOR BEST FUEL ECONOMY AND COLD STARTING, SELECT THE LOWEST
SAL VISCOSITY GRADE OIL
FOR THE EXPECTED TEMPERATURE RANGE.
HOT
WEATHER
F
+ 100
+ 80
+ 60
+ 40
+ 20
0
+ 38
+ 27
+ 16
+4
-7
- 18
COLD
WEATHER
LOOK FOR
ONE OF THESE
LABELS
SAE 1OW-30
SAE 5W-30
PREFERRED
IF NEITHER SAE 5W-30 NOR SAE 1OW-30
GRADE
OILS ARE AVAILABLE, SAE 30
GRADE MAY BE USED AT TEMPERATURES
ABOVE 40 DEGREES
F (4 DEGREES C).
ANY OTHER GRADE OIL NOT RECOMMENDED
DO NOT USE SAE 1OW-40, SAE 2OW-50 OR
As shown in the chart, SAE 5W-30 is best for your vehicle. However, you
can use SAE 1OW-30 if it's going to be 0°F (-18°C) or above. These
numbers
on an oil container show its viscosity, or thickness. Do not use
other viscosity oils, such as
SAE lOW-40 or SAE 20W-50.
6- 12

Downloaded from www.Manualslib.com manuals search engine Explanation Of Scheduled Maintenance Services
Below are explanations of the services listed in the maintenance charts.
The proper fluids and lubricants to use are listed
in this section. Make sure
whoever services your vehicle uses these. All parts should
be replaced and
all necessary repairs done before you or anyone else drives the vehicle.
1.
2.
3.
4.
5.
ENGINE OIL AND OIL FILTER CHANGE“ - ALWAYS USE
API SERVICE
SH OR SG ENERGY CONSERVING I1 OILS OF THE
PROPER VISCOSITY. The
“SH7 or “SG7 designation may be shown
alone or in combination with others, such as “SWCD”, or
“SH, SG,
CD,” or “SG/CD”, etc. To determine the preferred viscosity oil for your
vehicle’s engine see “Engine Oil”
in the Index.
CHASSIS LUBRICATION - Lubricate the front suspension,
steering linkage, transfer case shift linkage, parking brake cab\
le guides,
and brake pedal springs at the intervals specified on the proper
maintenance schedule, or at every engine oil change, whichever \
comes
first.
Ball joints and king pin bushings should not be lubricated unless their
temperature is
10°F (-1 2°C) or higher. When the weather is cold, let
them warm up before lubricating them or they could be damaged.\

Also, be sure to check all the vehicle fluid levels at this \
time.
COOLING SYSTEM SERVICE* - Drain, flush and refill the
system
with new or approved recycled coolant conforming to “GM
Specification 6038-M”. See “Engine Coolant”
in the Index for the
proper coolant and mixture to use
in your vehicle.
Also inspect the hoses and replace them
if they are cracked, swollen, or
deteriorated. Clean the outside of the radiator and air conditioning
condenser. Wash the radiator neck.
To ensure proper operation,
pressure test the radiator and cap.
AIR CLEANER FILTER REPLACEMENT* - Replace at
specified intervals. Ask your dealer for the proper replacement
intervals for your driving conditions.
FRONT WHEEL BEARING REPACK
(2-WHEEL DRIVE ONLY)
- Clean and repack the front wheel
bearings at each brake relining,
or at the specified interval, whichever
comes first.
* An Emission Control Service
7-7

Downloaded from www.Manualslib.com manuals search engine Recommended Fluids & Lubricants
NOTE: Fluids and lubricants identified below by name, part number or
specification may be obtained from your GM Dealer.
USAGE
Engine Oil
Engine Coolant Hydraulic Brake Systems
Parking Brake Cable
Power Steering System
Manual Steering Gear
Automatic Transmission
Differential: a. Standard
- Front and
Rear Axle
b. Locking
Transfer Case Column Shift
FLUIDLUBRICANT
API service SH or SG Energy
Conserving I1 oils
of the proper
viscosity. The “SH” or
“SG’
designation may be shown alone or in
combination with others, such as
“SWCD”, or
“SH, SG, CD,” or
“SGKD”, etc. To determine the
preferred viscosity oil for your
vehicle’s engine (e.g. SAE 5W-30).
See “Engine Oil”
in the Index.
Mixture of water and a good quality
ethylene glycol base antifreeze or an
approved recycled coolant conforming
to GM Specification GM-6038-M
(GM Part No. 1052103).
Delco Supreme I1 brake fluid
(GM
Part No. 1052535 or DOT-3).
Chassis lubricant meeting
requirements of NLGI Grade 2,
Category LB or GC-LB or (GM Part
No. 1052497).
GM Hydraulic Power Steering Fluid
(GM Part No. 1052884) or equivalent.
GM Lubricant (GM Part
No. 10521 82) or equivalent.
DEXRON @-I11
is preferred, if
unavailable use DEXRON @-IIE .
a. SAE-80W-90 GL-5 gear lubricant
(GM Part
No. 105227 1).
b. SAE-80W-90 gear lubricant (GM
Part
No. 1052271).
DEXRON@-IIE Automatic
Transmission Fluid.
Chassis lubricant meeting
requirements of NLGI Grade 2,
Catagory LB or GC-LB
(GM Part
No. 1052497).
7- 13