wheel CHEVROLET AVALANCHE 2007 2.G Owners Manual

Changing a Flat Tire
If a tire goes at, avoid further tire and wheel
damage by driving slowly to a level place.
Turn on your hazard warning ashers.
SeeHazard Warning Flashers on page 206
for more information.{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over
or fall on you or other people. You and
they could be badly injured or even killed.
Find a level place to change your tire.
To help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put the shift lever in PARK (P).
3. If you have a four-wheel-drive vehicle,
be sure the transfer case is in a drive
gear — not in NEUTRAL.
CAUTION: (Continued)
516

CAUTION: (Continued)
4. Turn off the engine and do not restart
while the vehicle is raised.
5. Do not allow passengers to remain
in the vehicle.
6. Put the wheel blocks at the front and
rear of the tire farthest away from
the one being changed. That would
be the tire on the other side, at the
opposite end of the vehicle.
When your vehicle has a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.The following information will tell you how to use
the jack and change a tire.
517

Removing the Spare Tire and Tools
The jack and the wheel blocks are located
under a cover near the passenger side rear seat.
To remove the jack and wheel blocks, do the
following:
1. Remove the jack cover by turning the two
wing nuts one-quarter turn counterclockwise
and pulling the jack cover off.A. Wheel Blocks
B. Knob
C. Wing Nut
D. Retaining HookE. Jack
F. Jack Head
G. Mounting
Bracket
2. Release the jack (E) from the mounting
bracket (G) by turning the knob (B) on the jack
counterclockwise to lower the jack head (F)
from the mounting bracket.
Rear Seat (Passenger Side) Jack Cover
518

3. Remove the wheel blocks (A) attached to
the jack (E) by turning the wing nut (C)
counterclockwise. Place the wheel blocks
where needed as indicated in previously in
this section.
The tools for changing a at tire are located in the
passenger’s side top-box storage unit.
To remove the tools, do the following:
1. Open the top door on the passenger’s side
top-box storage unit. Use the ignition/door
key to unlock it if it is locked. SeeTop-Box
Storage on page 191for more information.
2. Remove the black pouch from the storage box.
You now have all of the tools you will need to
lower the spare tire and change a at.
Top-Box Storage Unit (Passenger’s Side)
519

To access the spare tire, refer to the following
graphics and instructions:
A. Spare Tire
(Valve Stem
Pointed Down)
B. Hoist Assembly
C. Hoist Cable
D. Tire Retainer
E. Hoist ShaftF. Hoist End of
Extension Tool
G. Hoist Shaft
Access Hole
H. Wheel Wrench
I. Jack Handle
Extension
J. Spare Tire Lock1. Open the hoist shaft access cover on the
bumper to access the spare tire lock (J).
2. Insert the ignition key, turn it clockwise and
then pull it to remove the spare tire lock.
3. Assemble the two jack handle extensions (I)
and wheel wrench (H) as shown.
520

4. Insert the open
end of the
extension (F)
through the
hole in the
rear bumper (G)
(hoist shaft
access hole).
Be sure the hoist end (F) of the extension
connects to the hoist shaft. The ribbed square
end of the extension is used to lower the
spare tire.5. Turn the wheel wrench counterclockwise to
lower the spare tire to the ground. Continue
to turn the wheel wrench until the spare
tire can be pulled out from under the vehicle.
If the spare tire does not lower to the
ground, the secondary latch is engaged
causing the tire not to lower. SeeSecondary
Latch System on page 529for more
information.
6. Use the wheel
wrench hook that
allows you to
pull the hoist cable
towards you, to
assist in reaching
the spare tire.
521

7. Tilt the tire retainer
at the end of the
cable when the tire
has been lowered,
so it can be
pulled up through
the wheel opening.
8. Put the spare tire near the at tire.Removing the Flat Tire and
Installing the Spare Tire
Use the following pictures and instructions to
remove the at tire and raise the vehicle.
The tools you will be using include the jack (A),
the wheel blocks (B), the jack handle (C), the jack
handle extensions (D), and the wheel wrench (E).
522

1. If your vehicle has
wheel nut caps,
loosen them
by turning the
wheel wrench
counterclockwise.
If the vehicle has a center cap with wheel nut
caps, the wheel nut caps are designed to
stay with the center cap after they are
loosened. Remove the entire center cap.
If the wheel has a smooth center cap, place
the chisel end of the wheel wrench in the
slot on the wheel and gently pry it out.2. Use the wheel
wrench to loosen all
the wheel nuts. Turn
the wheel wrench
counterclockwise to
loosen the wheel
nuts. Do not remove
the wheel nuts yet.
523

Front Tire Flat:If the at tire is on a front tire
of the vehicle, you will need to use the jack
handle and only one jack handle extension.Attach the wheel wrench to the jack handle
extension. Attach the jack handle to the
jack (A). Position the jack on the frame behind
the at tire near the front body mount as
shown. Turn the wheel wrench clockwise to
raise the vehicle. Raise the vehicle far enough
off the ground so there is enough room for
the spare tire to clear the ground.
Front Position
525

Rear Tire Flat:If the at tire is on a rear tire
of the vehicle, you will need to use the jack
handle (B) and both jack handle extensions (C).Attach the wheel wrench (D) to the jack handle
extensions (C). Attach the jack handle (B) to
the jack (A). Use the jacking pad provided on
the rear axle. Turn the wheel wrench (D)
clockwise to raise the vehicle. Raise the vehicle
far enough off the ground so there is enough
room for the spare tire to clear the ground.
4. Remove all the
wheel nuts.
5. Take off the at tire.
Rear Position
526