brake CHEVROLET CAMARO 1967 1.G Chassis Owner's Manual

REAR SUSPENSION AND DRIVE LINE 4-7

tioned vertically in the torque arm before ap-

plying pressure to the puller screw.

5.
Remove shim and bearing spacer from spindle

support.

6. Note size of shim used. If dial indicator reading

was more than
.008",
select a shim thinner by the

amount needed to bring end play within limits. If

dial indicator reading was less than
.001",
select a

shim thicker by the amount needed to bring end play

within limits.

NOTE: Shims are available in thicknesses from

.097"
to .148" in increments of
.003".

EXAMPLE: Bearing end play reading obtained

on dial indicator was
.011",
.003" over limit.

Bearing shim removed from spindle measures

.145".
New shim installed measures .139", .006"

smaller. End play is now decreased by .006" and

is
.005",
which is within the .001" to .008" limit.

7.
After determining shim thickness, install bearing

spacer and shim on spindle. Position spindle in

spindle support.

8. Press inner bearing race and roller assembly on

spindle as follows.

a. Position Tool J-4731 over spindle and against

bearing inner race.

b.
Position washer and spindle nut on spindle and

proceed to tighten nut until bearing is forced on

spindle sufficiently to allow spindle drive flange

to be installed (fig. 13). Remove spindle nut,

washer and Tool
J-4731.
Discard nut and use a

new one for final assembly.

9. Position drive flange over spindle, making sure

flange is aligned with spindle splines. Install washer
Fig.
13—Installing Drive Spindle to Support (Corvette)

and nut on spindle then tighten nut to specifications

and install cotter pin. If specified torque does not

permit cotter pin insertion, tighten nut to next flat.

10.
Seat spindle support outer seal in bore by using

screw driver, or other suitable tool, to press against

metal portion of seal.

11.
Install brake disc and caliper. Refer to Section 5

for details of brake disc and caliper installation.

12.
Install axle drive shaft, wheel and tire assembly,

adjust camber cam to original position and torque

all components to specifications.

COMPONENT PARTS REPLACEMENT

(Chevrolet, Chevelle, Chevy II and Camaro)

COIL SPRING

Chevrolet

Removal

To remove either or both rear coil springs proceed

as follows.

1.
Raise rear of vehicle and place jack stands under

frame. Support vehicle weight at rear, using either

a jack or post of twin-post hoist under axle.

2.
Remove both rear wheels from vehicle.

3.
With the car supported as in Step 1, so that the rear

springs are compressed by weight of vehicle; per-

form the following:

a. Disconnect both rear shock absorbers from the

anchor pin lower attachment.

b.
Loosen the upper control arm(s) rear pivot bolt

(do not remove the nut).

C. Loosen both the left and the right lower control

arm rear attachment (do not disconnect from axle

brackets).

d. Remove the rear suspension tie rod from the

stud on the axle tube.

4.
At the lower seat of both rear coil springs, slightly

loosen the nut on the bolt that retains the spring and

seat to the control arm. When the nut has been

backed off the maximum permissible, all threads of
the nut should still be engaged on the bolt.

CAUTION: Under ,no condition should the nut,

at this time, be removed from the bolt in the

seat of either spring.

5.
Slowly lower the support (jack or hoist post) that has

been in place under the rear axle, thereby allowing

the axle to swing down, carrying the springs out of

their upper seat and providing access for spring

removal.

6. Remove the lower seat attaching parts from each

spring, then remove the springs from the vehicle

(fig. 14).

Installation

1.
Position the springs in their upper seat so that end

of top coil is 3/8" ± 1/8" from end of stop. Install

the lower seat parts on the control arm, with the nut

finger tight on the spring retainer bolt.

NOTE: Omit the lock washer under the special

high carbon bolt, so that sufficient bolt thread

will be available to start the nut. The lock

washers will be installed later (in Step 4).

2.
By alternately raising the axle slightly and then

re-snugging the nut on each spring lower seat bolt,

move the axle upward until vehicle weight is fully

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-9

Fig.
17—Rear Spring—Exploded View (Chevy II)

LEAF SPRING, SPRING SEAT PADS, SPRING EYE

BUSHINGS Chevy II (Fig. 17)

Removal

1.
Raise vehicle and support rear axle assembly.

2.
Pull parking brake cable out of lower spring pad

mounting bracket clamp and disconnect cable above

axle housing. Remove four nuts securing lower

spring pad mounting bracket to axle spring seat

(fig. 18). Drop lower bracket and remove rubber

spring pad.

3.
Loosen and drive out front spring eye bolt. Lower

spring and remove front rubber eye bushing (fig. 19).

4.
Remove nuts from rear spring shackle (fig. 20),

spread shackle to separate it from spring eye and

support bracket and remove spring. Remove rear

spring eye bushings.

5.
Remove upper spring pad cushion.

Installation

1.
Inspect spring eye bushings and spring pads for ex-

cessive wear or aging and replace as necessary.

Inspect spring rear shackles, front spring bracket

and eye bolt for bending or cracking and correct

where needed.

2.
Assemble spring rear shackle as follows:

a. All except Station Wagons (fig. 21).
Fig.
19—Removing Front Eye Bushings (Chevy II)

3.
' Fig. 20—Disassembling Rear Spring Shackle (Chevy II)

1.
Insert inboard rubber spring eye bushings into

i'ear spring eye and outboard shackle bushings

into shackle mounting bracket.

2.
Position spring and install shackle to spring

and mounting bracket with top nut toward out-

board of vehicle and bottom nut toward vehicle

centerline.

3.
Tighten nuts but-do not torque at this point,

b.
Station Wagon (fig. 22):

When installing shackle as in Step 2 above, top

nut should be toward centerline of vehicle and

bottom nut toward outboard of vehicle.

Insert inboard rubber bushing into front spring eye.

Fig.
18—Removing Lower Pad Bracket (Chevy II)
Fig.
21—Rear Spring Shackle Exploded View-All

Except Station Wagon (Chevy II)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-11

lower cushion

correct.
will be aligned if installation is

Fig.
25—Installing Spring Front Bushing (Camaro)

Unnecessary torque applied after flange is

seated will tend to distort flange and reposition

bushing in spring.

i. Disassemble bushing installation tools and re-

move from spring.

8. Pry parking brake cable out of the retainer bracket

mounted on the spring mounting plate.

9. Remove spring bracket-to-axle bracket retaining

nuts,
remove upper and lower rubber spring pads

and bracket.

10.
Support spring, then remove lower bolt from spring

rear shackle. Separate shackle and withdraw spring

from vehicle.

11.
Remove rear spring shackle upper bolt and withdraw

shackle bushings from frame.

Installation

1.
Position spring front mounting bracket to spring

front eye. Spring attaching bolt must be installed

so that head of bolt is toward center of vehicle.

2.
Position spring shackle upper bushings in frame,

position shackles to bushings and loosely install

bolt and nut.

3.
Install bushing halves in spring rear eye, place

spring to shackles and loosely install shackle lower

bolt and nut.

NOTE: When installing spring, make sure

spring is positioned so that parking brake cable

is on underside of spring.

4.
Raise front end of spring and position bracket to

underbody. Guide spring into position so that it will

index in the axle bracket and also make sure that

the tab on spring bracket is indexed in slot pro-

vided in the underbody.

5.
Loosely install spring-to-underbody bracket.

6. Position spring upper cushion between spring and

axle bracket so that spring cushion ribs align with

axle bracket locating ribs.

7.
Place lower spring cushion on spring so that .cushion

is indexed on locating dowel. Upper cushion and
8. Place lower mounting plate over locating dowel on

spring lower pad and loosely install retaining nuts.

9. If new mounting plate was installed, transfer parking

brake cable retaining bracket to new plate.

10.
Position shock absorber to spring mounting plate and

loosely install eye bolt and nut - head of bolt should

be toward front of vehicle.

11.
Position parking brake cable in retaining bracket and

securely clamp bracket to retain cable.

12.
Remove stand jacks and lower vehicle so that weight

of vehicle rests on suspension components. Torque

all affected parts to specifications.

SHOCK ABSORBER

Chevrolet and Chevelle

Removal

1.
Raise rear of vehicle and support rear axle

assembly.

If equipped with superlift shock absorber, disconnect

air line from shock absorber.

Disconnect shock absorber at upper mounting bracket

by removing the two retaining bolts. Refer to Figure

26 for shock absorber mounting details. (Chevelle

components shown as typical.)

Disconnect shock absorber at lower attaching bracket

and remove shock.

NOTE: When performing any service opera-

tions that requires removal or loosening of the

lower attaching nut, it is essential that the stud

be prevented from turning. A hex is located on

the stud between the axle bracket and shock

absorber in order that a wrench may be used

for this purpose. Failure to hold the stud in

this manner will result in damage to the mer

chanical bond between the shock absorber bush-

ing and the mounting stud.
2.

3.

STATION WAGON AND PICKUP

Fig.
26—Shock Absorber Mounting—Exploded View

(Chevelle)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-14

Fig.
32—Upper Control Arm Bushing Installation (Chevrolet)

Installation

1.
Position rear of control arm into axle bracket and

loosely install the pivot bolt.

2.
Align the forward end of the control arm with the

rear crossmember and install front bracket bolts

through holes. Raise or lower nose of carrier as

/ required to help align bracket and crossmember.

3.
Install crossmember reinforcement plate, lock

washers and nuts to retain bracket in place.

4.
Position vehicle so that weight is on suspension

components and torque all affected parts to

specifications.

Chevrolet Lower

Removal

1.
Raise vehicle and remove shock absorber and spring

as outlined in this section.
NOTE:
If both rear suspension lower control

arms are to be removed, support the rear axle

in such a manner to prevent damage to brake

lines and to prevent assembly from falling.

2.
Note position of control arm in forward attaching

bracket and disconnect control arm at forward and

rearward attaching points. Remove assembly from

vehicle.

Bushing Replacement

Lower control arm front and rear bushing assemblies

are not interchangeable and require separate removal

and installation procedures.

1.
Replace the front bushing as follows.

a. Center Receiver J-7574-4 over flanged end of

bushing and position Spacer J-7574-3 over bush-

ing and between sides of control arm. Using

Remover J- 7574-1 against small end of bushing,

press bushing from control arm. Refer to Figure

33 for installed view of tools.

b.
Position bushing in control arm making sure of

correct installation. Small end of bushing will

pass through one side without any interference.

c. Position Puller Screw J-21058-15 through In-

staller Adapter J-7574-2--head of puller screw

should rest against flat side of adapter.

d. Install adapter and screw through bushing with

adapter resting against flange portion of bushing.

Install Receiver J-21058-6 and Bridge J^-21058-7

on opposite side of control arm (fig. 34).

e. Install thrust bearing and Nut J-21058-8. Screw

nut against J-21058-7 to maintain proper relation-

Fig.
33—Lower Control Arm Front Bushing Removal (Chevrolet)
Fig. 34—Lower Control Arm Front Bushing Installation

(Chevrolet)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-18

ig.
44—Rear Suspension Tie Rod Attaching Points (Chevrolet)

Bushing
Replacement

The following bushing removal procedure is effective

for both ends of the tie rod used on station wagons and

the left end of the tie rod used on all models except

station wagons.

1,
With tie rod bushing centered over Tool J-7877-2

and with tie rod supported horizontally, press or

drive bushing from rod, using Tools J-7877-1 and

J-7079-2 as shown in Figure 45.

2.
With tie rod centered over Tool J-7877-2 and rod

supported horizontally, press or drive bushing into

arm using Tools J-7877-3 and J-7079-2 as shown

in Figure 45. Tool J-7877-3 should bottom on tie

rod when bushing is fully installed.
fig.
45—Tie Rod Bushing Replacement (Chevrolet)

Installation

1.
Mount the tie rod to the axle bracket stud. Install

nut and special washer but do not tighten.

NOTE:
On the tie rod used on all models except

station wagons, place flanged portion of bushing

against attaching bracket.

2.
Install the bolt, lock washer and nut to the frame

bracket (fig. 44). Do not tighten.

NOTE:
Bolt may be installed from either

direction.

3.
Lower vehicle to floor (if raised) and bounce rear

end several times to settle bushings. Tighten af-

fected parts to specifications.

COMPONENT PARTS REPLACEMENT (CORVETTE)

WHEEL SPINDLE AND SUPPORT (Fig. 46)

Removal

Hemdve wheel drive spindle as outlined previously in

this section under "Wheel Bearing Adjustment".

Repairs

Out of 3/8" square steel bar stock, make bearing

removers and use as shown in Figure 47.

After removing deflector, spindle inner grease seal

and inner bearing race, bearing cups may be re-

moved while spindle support is still mounted to the

torque arm, by inserting remover tool and tapping

cup out. New bearing cups are installed using Tool

J-7817 cup installer and handle J-8092 (fig. 48).

To remove spindle support from torque arm, pro-

ceed as follows.

a. Disconnect parking brake cable from actuating

lever.

b.
Remove four nuts securing support to torque arm

and withdraw brake backing plate and position it

out of the way.

c. Disconnect shock absorber lower eye from strut

rod mounting shaft. It may be necessary to sup-

port spring outer end before disconnecting shock
absorber, as shock absorber has internal rebound

control.

d. Remove cotter pin and nut from strut rod mount-

ing shaft, then pull shaft from support and strut

rod.

e. Spindle support may then be removed and bearing

cups serviced as in Step 2 above.

4.
To remove drive spindle outer bearing and seal

proceed as follows.

a. Position Tool J-8331 between chamfered edge of

bearing seat and inner race of bearing (fig. 49).

Clamp Tool J-8331 in a vise and apply pressure

to unseat bearing.

CAUTION: Use extreme caution when position-

ing Tool J-8331 against machined surface of

spindle. Make sure all tool imperfections such

as nicks and burrs are removed from spindle

contact area before applying pressure to unseat

bearing.

b.
Position Tool J-8331 and spindle in an arbor

press and press bearing from spindle (fig. 50).

c. Remove outer seal and inspect for damage--re-

place if necessary. Outer seal must be placed on

spindle before outer bearing inner race and roller

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION
AND
DRIVE LINE
4-19

BRAKE BRAKE

DISC SHOE

OUTER

BEARII
-. -,
-«#*;>•
BRAKE

CAMPER

/

/ /

/ /

si—a

wC—
SPINDLE

^ SUPPOR1

BEARING

^ SPACER

INNER

" BEARING

DRIVE

" FLANGE

BEARING

-PRELOAD

SPACER

DEFLECTOR

CONTROL

ARM

Fig.
46-Wheel Spindle
and
Support Cross-Section (Corvette)

assembly is installed.

d. Pack outer bearing with a high-melting point

wheel bearing lubricant and position on spindle.

Large end of bearing should be toward shoulder

on spindle.

e. Press bearing on spindle using a bearing spacer

and Tool J-9436 as installers, as shown in Fig-

ure 50.

5. Pack spindle inner bearing with a high-melting point

-wheel bearing lubricant and position bearing in

spindle support - small end of bearing should be

positioned inward.

PRESS RAM

BEARING CUP
Fig.
48—Installing Spindle Bearing Cup (Corvette)

Fig.
49—Unseating Drive Spindle Outer Bearing (Corvette)

Fig.
47—Bearing Cup Removal (Corvette)
Fig.
50—Removing and Installing Drive Spindle

Outer Bearing (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-20

Fig.
51—Shock Absorber Installation (Corvette)

6. Tap new spindle inner grease seal into seal bore

and install deflector over support inner end.

Installation

1.
Position support over torque arm bolts with strut

rod fork toward center of vehicle and downward.

Place backing plate over studs and torque nuts to

specifications.

2.
Connect parking brake cable to actuating lever.

3.
Install drive spindle assembly as outlined previously

in this section under "Wheel Bearing Adjustment".

4.
If new spindle support or associated parts are in-

stalled, determine correct shim size as follows.

a. Assemble spindle to support, using a .145" shim.

b.
Check bearing adjustment and correct as neces-

sary, following adjustment procedures previously

outlined.

DIFFERENTIAL CARRIER SUPPORT

BRACKET REPLACEMENT

1.
Place a 1/2" thick block of wood or steel between

nose of differential carrier and floor pan. This will

prevent carrier from twisting upward when support

bracket is disconnected.

2.
Remove carrier support-to-crossmember attaching

bolt.

3.
Remove nut from both of the bracket-to-carrier

through bolts.

4.
Slide bolts to one side until bolt head contacts floor

well. Mark the floor well at this point and drill a

3/4"
diameter hole for each bolt in floor well and

remove bolts.

5. Assemble carrier support bracket by reversing

above procedure. Torque all affected parts to

specifications.

6. Insert plastic plugs from the inside of the floor well

holes to prevent dust and water entry.
STRUT ROD SHAFT STRUT ROD

CAMBER CAM

AND BOLT

Fig.
52—Strut Rods (Corvette)

SHOCK ABSORBER (Fig. 51)

Removal

1.
Disconnect shock absorber upper mounting bolt*

2.
Remove lower mounting nut and lock washer.

3.
Slide shock upper eye out of frame bracket and pull

lower eye and rubber grommets off strut rod mount-

ing shaft.

4.
Inspect grommets and shock absorber upper eye for

excessive wear.

Installation

1.
Slide upper mounting eye into frame mounting

bracket and install bolt, lock washer and nut.

2.
Place rubber grommet, shock lower eye, inboard

grommet, washers and nut over strut rod shaft.

3.
Torque nuts to specifications.

STRUT ROD AND BRACKET (Fig. 52)

Removal

1.
Raise vehicle enough to provide working clearance.

2.
Disconnect shock absorber lower eye from strut

rod shaft.

3.
Remove strut rod shaft cotter pin and nut. With-

draw shaft by pulling toward front of vehicle (fig. 53).

4.
Mark relative position of camber adjusting cam and

Fig.
53-Removing Strut Rod Shaft (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-23

Fig.
62—Torque Control Arm (Corvette)

2.
Place center clamp plate in position and install four

bolts and washers. Tighten bolts and torque to

specifications.

3.
Raise spring outer end with floor jack until spring

is nearly flat and secure with chain as in Step 3-

Removal.

.4.
Lower jack, align torque control arm with spring

end and insert link bolt, rubber cushions and re-

tainers. Install castellated nut on link bolt and

tighten until cotter pin hole in bolt is visible. In-

sert new cotter pin and bend ends around.

5. Raise spring end with jack under link bolt, and re-

move chain and C clamp when loose.

6. Carefully lower jack, making sure rubber cushions

remain indexed in retainers.

7. Remove jack and repeat on opposite side. Install

wheels and tires, remove frame supports and lower

vehicle to floor.

TORQUE CONTROL ARM (Fig. 62)

Removal

1.
Disconnect spring on side torque arm is to be re-

moved. Follow Steps 1-6, Spring-Removal.

NOTE:
If vehicle is so equipped, disconnect

stabilizer rod from torque arm - refer to

"Stabilizer Rod Replacement".

2.
Remove shock absorber lower eye from strut rod

shaft.

3.
Disconnect and remove strut rod shaft and swing

strut rod down.

4.
Remove four bolts securing axle drive shaft to

spindle flange and disconnect drive shaft.

NOTE:
It may be necessary to force torque

arm outboard to provide clearance to drop drive

shaft.

5. Disconnect brake line at wheel cylinder inlet or

caliper and from torque arm. Disconnect parking

brake cable.

6. Remove torque arm pivot bolt and toe-in shims and

pull torque arm out of frame. Tape shims together

and identify for correct reinstallation.
RETAINER

RETAINER

PLATE

BUSHING

CONTROL ARM

Fig.
63—Torque Control Arm Bushing Cross-Sect ion (Corvette)

NOTE:
For service operations pertaining to

the spindle support assembly, refer to service

operations under Wheel Spindle and Support

earlier in this section.

Repairs (Fig. 63)

1.
Using 11/16" drill, drill out flared end of bushing

retainer (fig. 64).

2.
Remove special retainer plate and tap retainer out

of bushing.

3.
Remove bushings by spreading them apart with a

chisel and tap out of arm (fig. 65).

NOTE:
If bushing diameters are severely

rusted in torque arm, and arm tends to spread

during removal, clamp arm in a C-clamp to

prevent spreading.

Fig.
64—Drilling Out Retainer Flare (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-24

4

i*
5

Fig.
65—Removing Bushings (Corvette)

4.
Lightly oil new bushing diameters (not rubber por-

tion) and start bushings squarely in arm.

5. Install Tool J-7055-1 as shown in Figure 66 and

press bushings into place.

6. When bushings are fully installed, place special

plate over flared portion of new bushing retainer

and insert retainer into bushing.

7. Out of 5/8" thick steel plate 1-1/2" wide make flar-

ing tool support to the dimensions shown in Figure

67 and drill clearance holes as shown for 2
—
1/2"

bolts.

8. Place fabricated back-up plate on flared end of bush-

ing retainer and assembly Tool J-8111-23 to plate

with 2-1/2" bolts 5" long. Make sure threaded hole

in J-8111-23 is centered over unflared end of bushing

retainer and that chambered retainer plate is cen-

tered over retainer tube.

9. Lightly oil pointed end of J-8880-5 screw and thread

into J-
8111-23
until pointed "end contacts bushing

retainer. Continue threading J-8111-23 until retainer

is flared (fig. 68).

Installation

1.
Place torque arm in frame opening.

2.
Place toe-in shims in original position on both sides

of torque arm, install pivot bolt and tighten but do

not torque at this point.
Fig.
67—Flaring Tool Back-Up Plate (Corvette)

3.
Raise axle drive shaft into position and install to

drive flange. Torque bolts to specifications.

4.
Raise strut rod into position and insert strut rod

shaft so that flat lines up with flat in spindle sup-

port fork. Install nut and torque to specifications.

5. Install shock absorber lower eye and tighten nut

to specifications.

6. Connect spring end as outlined under Spring-

Bistallation, Steps 3-6'.

NOTE:
If vehicle is so equipped, connect sta-

bilizer shaft to torque arm - refer to "Sta-

bilizer Shaft Replacement".

7. Install brake disc and caliper, wheel and tire and

lower vehicle. Tighten torque arm pivot bolt. Bleed

brakes as outlined in Section 5-Brakes.

SUSPENSION CROSSMEMBER

Removal

1.
Disconnect and remove spring as outlined under

Spring-Removal.

2.
Remove differential carrier assembly as outlined

under Differential Carrier-Removal in this section.

3.
Support crossmember, remove bolts securing

crossmember isolation mounts to frame and lower

crossmember (fig. 69).

Fig.
66—Installing Bushings (Corvette)
Fig.
68—Flaring Retainer (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION
AND
DRIVE LINE
4-26

DRIVE LINE

REAR AXIE

INDEX

Page

General
Description
4-26

Chevrolet,
Camaro,
Chevelle
and
Chevy
II 4-26

Corvette
4-26

Maintenance
and
Adjustments
4-27

Lubricant
4.37

Lubricant'
Leaks
4_27

Axle Bolts
and
Wheel
Nuts
4-27

Rear Axle Noise
Diagnosis
4-29

Gear Noise
4_29

Bearing
Noise
4-29

Failure
Analysis
4^9

Hypoid
Gears
4..3Q

Differential Gears. 4_30

Bearings
....'.
4.30

Component Parts Replacement

(Chevrolet, Chevelle, Camaro and Chevy n ..... 4.30

Axle Assembly ,. . 4_30

Removal 4 30

Installation * ' 4 3Q
Axle Shaft . . . 4-31

Removal 4-31

Wheel Bolt Replacement 4-31

Oil Seal and/or Bearing Replacement. 4-31

Brake Flange Plate Replacement 4-31

Installation 4-32

Pinion Flange, Dust Deflector and/or

Oil Seal Replacement 4-32

Component Parts Replacement (Corvette) 4-34

Axle Driveshaft .- 4-34

Removal 4-34

Repairs 4-34

Installation. . 4-34

Pinion Flange, Dust Deflector and/or Oil Seal. .... 4-35

Removal 4-35

Inspection . 4-35

Installation .- 4-35

Differential Carrier 4-36

Removal 4-36

Installation 4-36

Positraction Differential Unit-On the Vehicle Check . . 4-37

\

GENERAL DESCRIPTION

CHEVROLET, CHEVELLE, CHEVY
I! AND
CAMARO

The rear axle
(fig. 72) is a
semifloating, fabricated

construction type consisting
of a
cast carrier with large

bosses
on
each
end
into which
two
welded steel tubes

are fitted.
The
carrier contains
an
overhung hypoid

pinion
and
ring gear.
The
differential
is a
two pinion

arrangement.

The axle housing
is
made up
of
two steel welded tubes

pressed into
the
crossbore
of the
cast carrier
-
each

tube
is
puddle welded
at
three places
to the
carrier.

Welded-on brackets provide attachment points
for

Chevelle springs,; shock absorbers,
and
lower control

arms.
Chevrolet models have welded-on brackets
for

control arms,
tie
rod, and shock absorbers. The housing

on Chevy II and Camaro has welded brackets
for
mounting

lower spring
pad
and shock absorber.
A
welded flange
is

provided
for
brake flange plate attachment.

The overhung hypoid drive pinion
is
supported
by
two

preloaded tapered roller bearings.
The
pinion shaft
is

sealed
by
means
of a
molded, spring loaded, rubber seal.

The seal
is
mounted
on the
pinion shaft flange which
is

splined and bolted
to
the hypoid pinion shaft.

The hypoid ring gear
is
bolted
to a
one-piece differen-

tial case which
is
supported
by two
preloaded tapered

roller bearings.

CORVETTE

The Corvette rear axle
is of the
type where
the dif-
ferential carrier housing enclosing
the
differential
and

hypoid gears
is
supported
on a
crossmember mounted
to

the chassis frame.
The
differential
is
connected through

universal joints
to the
drive shafts
and
wheels
(fig. 73).

The internal components
of the
carrier
are of
conven-

tional design, incorporating
a
hypoid gear
set
with
an

overhung pinion supported
on two
pre-loaded, tapered

roller bearing assemblies,
and a
two-pinion differential

assembly supported
on
tapered roller bearings. Pinion

mounting distance adjustments
are
made through the
use

of shims,
as are the
differential bearing pre-load
and

backlash adjustments.
The
differential side gears drive

two splined yokes which
are
retained laterally
by
snap

rings located on the yoke splined end. The yokes
are
sup-

ported on caged needle bearings pressed into
the
carrier,

adjacent
to the
differential bearings.
A
lip seal, pressed

in outboard
of
the bearings, prevents
oil
leakage and dirt

entry.
The
carrier cover
is
bolted
to the
carrier and

provides accessibility
to the
internal parts.
The
cover

incorporates two integral, reinforced mounting pads which

serve
as the
carrier attaching point
to the
suspension

crossmember,
and an
attaching point
for the
spring

center section. The filler plug
is
located on the right side

of the cover near the bolting flange.

All service operations allow carrier removal without

removing
the
carrier cover. Cover removal
is
not nec-

essary
in any of the
service procedures except
in
the

case
of
complete carrier housing replacement,
as the

carrier and cover
are
serviced
as
an assembly.

CHEVROLET CHASSIS SERVICE MANUAL