buttons CHEVROLET CAMARO 1994 4.G Owners Manual
[x] Cancel search | Manufacturer: CHEVROLET, Model Year: 1994, Model line: CAMARO, Model: CHEVROLET CAMARO 1994 4.GPages: 292, PDF Size: 15.35 MB
Page 52 of 292
Downloaded from www.Manualslib.com manuals search engine Features and Controls
You can match a transmitter to as many
different vehicles
as you own, provided
they are equipped with exactly
the same
model system. (General Motors offers
several different models of these systems
on their vehicles.) Each vehicle can have
only two transmitters matched to
it.
To match transmitters to your vehicle:
1. Find the Data Link Connector (DLC).
It is
in the bottom of the instrument
panel near the steering column.
2. Insert one end of a fused jumper into
terminal
“G.” Terminal “G” is the top
terminal on the far right.
jumper into terminal “A.” Terminal
“A” is the bottom terminal on the far
left.
3. Insert the other end of the fused
You have grounded the program input
line. You should hear the door locks lock
and unlock within one to three seconds.
When matching transmitters, the first
transmitter code matched
will be stored in
both memories until a second transmitter
is matched. This means
that the second transmitter
will not work until
it is
matched
in step 5.
4. Press any button on the first
transmitter. The door locks should
lock and unlock.
5. Press any button on the second
transmitter. The door locks should
lock and unlock.
6. Remove the fused jumper from the
DLC. The system
will not work unless
the jumper
is removed.
transmitters work correctly.
7. Check that all the buttons on both
[f the transmitters don’t work, or if you’d
rather not match the transmitters yourself,
see your Chevrolet dealer.
Battery Replacement
Under normal use, the batteries in your
key chain transmitter should last about
:wo years.
You can tell the batteries are weak if the
:ransmitter won’t work at the normal
-ange
in any location. If you have to get
:lose
to your vehicle before the
:ransmitter works, it’s probably time to
:hange the batteries.
Page 87 of 292
Downloaded from www.Manualslib.com manuals search engine T-Top Sunshades
1. Start with the panel marked “DRIVER
FRONT.” Unlatch the driver-side
T-top, raise
it halfway and close the
latch handle.
2. With the top raised and resting on the
center roof rail, slide the flat edge of
the sunshade panel
(with the vinyl
side to the glass) between the glass
and plastic trim, making sure the
edge marked “DRIVER FRONT” is
pointing to the front
of the vehicle.
3. Open the latch and close the T-top.
Check to see
if there are any gaps
showing. Unlatch the T-top and adjust
the sunshade as required.
4. Once the sunshade is installed
properly, you can stick the Velcro@
buttons on the glass
for a proper fit
every time you install the sunshades.
To do this, first remove the T-top with
the sunshade installed and place it
upside down on a table or bench.
Tdke care not
to scratch the glass.
-
5. Pull the sunshade back a little and
remove the backing paper from the
Velcro@ buttons. Push the sunshade
back into place sticking the Velcro@
to the glass.
6. Install the T-top, close the latch and
lock the T-top. Repeat the above steps
for the passenger-side sunshade.
85.
Page 116 of 292
Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
/- VOLUME TREB
PROG-RCL P
TUNE -3 FADE BASS
\
V SEEK P I 234 SET
[II] [OOOO]
AM-FM n
Scan
The scan function uses the same two
buttons as the seek function.
To
go to the next higher station and stay
there for a few seconds, press and hold
“SEEK
A’’ and then press “SEEK 7” for
an instant.
To go to the next lower station and stay
there for a few seconds, press and hold
“SEEK
7’’ and then press “SEEK A’’ for
an instant.
To stop the scan function, press either
“SEEK
A’’ or “SEEK v.”
Pushbuttons
The four pushbuttons let you return to
your favorite stations.
You can preset up
to 14 stations (7 AM and 7 FM).
To set the pushbuttons for up to eight
stations
(4 AM and 4 FM), just:
1. Tune in the station.
2. Press “SET.” (“SET” will appear on
the display for about five seconds.)
3. Within five seconds, press one of the
four pushbuttons. Whenever
you
press that button, the preset station
will return.
Repeat these steps for each pushbutton.
You can preset three mor e stations on
each band
by pressing a pair of buttons
next to each other at the same time. Just:
1. Tune in the station.
2. Press “SET.” (“SET” will appear on
3. Within five seconds, press two
the
display for about five seconds.)
pushbuttons next to each other at the
I1
same time. Whenever you press that
pair of buttons, the preset station wil
return.
Repeat these steps for each pair of
pushbuttons.
Setting the Tone
Bass: Slide the “BASS” levkfup to hear
more bass.
Treble: Slide the “TREB” lever up to
hear more treble.
If a station
is weak and noisy, move
“TREB” down to reduce the noise.
. . .114
Page 118 of 292
Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
[ VOLOBAL
POWER
1 TUNE 00 FADE
F
D
R
‘c AM-FM a
COMP RDM REV FWD SCAN PREV NEXT
AM!FM Stereo with Compact
Disc Player
To Play the Radio
Turn the upper knob to turn the system on
or off.
Volume
Turn the upper knob to adjust the volume.
AM-FM
Press the lower knob to get AM, FMl or
FM2.
. . . 116
Tune
Turn the lower knob to choose radio
stations.
Recall
Press “RCL” to reca .I1 the station being
played or the time.
Seek
Press “SEEK 4 ” or “SEEK ” to go to
the next lower
or higher station and stay
there.
Scan
Press “SCAN’ to hear each station for a
few seconds. When you want to stop
scanning, press “SCAN’ again or the
upper knob.
Pushbuttons
The five pushbuttons let you return to
your favorite stations.
To set the
pushbuttons for up to
15 stations (5 AM,
5 FMl and 5 FM2), just:
1. Press the lower knob to choose AM,
2. Tune in the station.
3. Press “SET.” (“SET” will appear on
the display for about five seconds.)
4. Within five seconds, press one of the
pushbuttons. Whenever you press that
button, the preset station
will return.
FMl or FM2.
Page 120 of 292
Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
To Play the Next Selection
Press “NEXT” to hear the next track now
(instead of waiting until
the present track
is finished).
If you press and hold this button or press
it more than once, the disc will advance
further.
To Replay the Current Selection
Press “PREV” to hear a track again.
If you press and hold this button, or press
it more than once, the disc will return to
previous tracks.
Reverse
Press and hold “REV” to rapidly return to
a favorite passage. Release
it to play the
passage.
Fast Forward
Press and hold “FWD’ to quickly
advance within
a track. Release it to
resume playing.
Scan
Press “SCAN” to listen to each track for
about
10 seconds. Press “RDM” or
“SCAN” to stop the scanning.
Compression
Press “COMP’ to make loud and soft
passages more nearly equal
in volume.
Random
Press “RDM” to hear a random selection
of tracks.
To Stop the Disc Player
0
0
0
Turn the power off or turn the ignition
key off. The disc stays
in the player
and will resume playing at the point
where
it stopped.
Press “ST-PL” to stop playing the disc
and switch to radio. Press “ST-PL,” to
restart
the disc at the point where it
stopped.
Press “EJCT” to eject the disc and the
radio
will play. The disc will start
playing
at track 1 when you reinsert it.
Theft-Deterrent Feature
Delco-Loc I1 is a security feature for the
compact disc player.
It can be used or
ignored. If ignored, the system functions
normally. If
it is used, your system won’t
be usable
if it’s ever stolen.
Setting Your Security Code
The instructions below tell you how to
enter a security code into the system. If
your vehicle loses battery power for
any
reason, you must enter the security code
again before the system
will turn on.
1. Write down any six-digit number and
2. Turn the ignition switch to the “Acc”
3. Turn the audio system off.
4. Press and hold pushbuttons “1” and
keep
it in a
safe place.
or
“Run” position.
“4” together until “---” shows on the
display.
You are now ready to enter your security
code. Don’t wait more than
15 seconds
between steps.
. . .118
Page 121 of 292
Downloaded from www.Manualslib.com manuals search engine 5. Press “SET” and “000” will appear
on the display.
~ 6. Press “SEEK 4 ” or “SEEK b ” and
hold until the first digit of your code
appears. Release the button.
7. Turn the lower knob to make the
second and third digits appear.
8. Press the lower knob and “000” will
appear on the display. Now you are
ready
to enter the last three digits of
your code.
9. Press “SEEK 4 ” or “SEEK b ” and
hold until the fourth digit of your
code appears. Release the button.
10. Turn the lower knob to make the
fifth and sixth digits of your code
appear.
11. Press the lower knob. “rEP” will
appear for five seconds, and then
“000” will appear.
through
11. If “SEC” appears, your
audio system is secured.
If “---”
shows on the display, your system is
not secured.
You must restart the
entire procedure again from step
5.
12. For verification, repeat steps 6
Shutting Off the Theft-Deterrent
Feature
If your audio system is secured (“SEC”
shows on display) and you wish to disable
it, enter your security code as follows,
pausing no more than
15 seconds
between steps:
1. Turn the ignition on. Make sure the
audio system is
off. The time will
show on the display.
together
until “SEC” shows on the
display.
3. Press “SET.” “000” will appear on the
display.
4. Press “SEEK 4 ” or “SEEK b ” and
hold until the first digit of your code
appears. Release the button.
5. Turn the lower knob until the second
and third digits appear.
6. Press the lower knob. “000” will
appear on the display.
7. Press “SEEK 4 ” or “SEEK b ” and
hold until the fourth digit of your
security code appears. Release the
button.
8. Turn the lower knob until the fifth and
2. Press pushbuttons “1” and “4”
sixth digits of your code appear.
9. Press the lower knob. If “---” shows,
you have shut off the theft-deterrent
feature. If
“SEC” shows, your audio
system is still secured.
NOTE: If you lose or forget your security
code, see your dealer for assistance.
Unlocking the Audio System after a
Power Failure
If power is disrupted to the audio system
while
in the “SEC” mode, the unit will
not work and “LOC”
will show on the
display whenever the ignition is on. To
unlock the unit:
1. Turn the ignition switch to the “Acc”
or “Run” position.
2. Press “SEEK 4 ” or “SEEK b ” and
hold until the first digit of your code
appears. Release the button.
3. Turn the lower knob to make the
second and third digits appear.
4. Press the lower knob. “000” will
appear on the display.
5. Press “SEEK 4 ” or “SEEK b ” and
hold until the
fourth digit of your
security code appears. Release the
button.
119.. .