radio CHEVROLET CAMARO 1994 4.G Owners Manual
[x] Cancel search | Manufacturer: CHEVROLET, Model Year: 1994, Model line: CAMARO, Model: CHEVROLET CAMARO 1994 4.GPages: 292, PDF Size: 15.35 MB
Page 51 of 292
Downloaded from www.Manualslib.com manuals search engine I9
Remote Lock Control (Option)
If your Chevrolet has this option, you can
lock and unlock your doors or unlock
your hatch from about
30 feet (9 m) using
the key chain transmitter supplied with
your vehicle.
Your Remote Lock Control operates on a
radio frequency subject to Federal
Communications Commission (FCC)
Rules.
This device complies with Part
15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device
may not cause harmful interference, and
(2) This device must accept any
interference received, including
interference that may cause undesired
operation. Should interference
to this system occur,
try this:
0 Check to determine if battery
replacement is necessary. See the
instructions on battery replacement.
0 Check the distance. You may be too
far from your vehicle. This product
has a maximum range.
0 Check the location. Other vehicles or
objects may be blocking the signal.
See your Chevrolet dealer or a
qualified technician for service.
Changes or modifications to this system
by other than an authorized service
facility could void authorization to use
this equipment.
Operation
The driver’s door will unlock
automatically when “UNLOCK’ is
pressed. If “UNLOCK” is pressed again
within five seconds, the passenger door
will also unlock. All doors will
lock when
“DOOR” is pressed. The hatch will
unlock when the opened trunk symbol is
pressed, but only when the ignition switch
is not
in “Run”, and the transmission is in
“P’ (Park) if you have an automatic
transmission. If you have a manual transmission, the
parking brake must be
set.
The system will
turn on the interior lights
for about
40 seconds, or until the ignition
switch is turned to “Run”, when you
unlock the doors or hatch. The interior
lights will come on for about two seconds
when you lock the doors.
Matching Transmitter(s) to Your
Vehicle
Each key chain transmitter is coded to
prevent another transmitter from
unlocking your vehicle. If a transmitter is
lost or stolen, a replacement can be
purchased through your dealer.
Remember to bring any remaining
transmitters with you when you
go to
your dealer. When the dealer matches the
replacement transmitter to your vehicle,
the remaining transmitters must also be
matched. Once the new transmitter is
coded, the lost transmitter will not unlock
your vehicle.
49. .
Page 57 of 292
Downloaded from www.Manualslib.com manuals search engine New Vehicle
“Break-In”
NOTICE:
Your modern Chevrolet doesn’t need
an elaborate “break-in.” But it will
perform better
in the long run if you
follow these guidelines:
Keep your speed at
55 mph (88
km/h) or less for the first 500
miles (804 km).
Don’t drive at any one speed
-
fast or slow - for the first 500
miles (804 km). Don’t make
full-throttle starts.
Avoid making hard stops for the
first
200 miles (322 km) or so.
During this time your new brake
linings aren’t yet broken
in. Hard
stops with new linings can mean
premature wear and earlier
replacement. Follow this
“breaking-in” guideline every
time
you get new brake linings.
D
I Ignition Switch
Vith the ignition key in the ignition
witch,
you can turn the switch to five
lositions:
KC (A): Position in which you can
lperate your electrical power accessories.
’ress
in the ignition switch as you turn
?e top
of it toward you.
,OCK (B): The only position in which
ou can remove the key. This locks your
teering wheel, ignition and automatic
7ansmission.
f you have an automatic transmission, the
znition switch can’t be turned to
LOCK” unless the shift lever is
in the
“P” (Park) position.
Off (C): Unlocks the steering wheel,
ignition and automatic transmission, but
does not send electrical power to any
accessories.
Use this position if your
vehicle must be pushed or towed.
A
warning tone will sound if you open the
driver’s door when the ignition
is in “Off’
and the key is
in the ignition.
Run (D): Position to which the switch
returns after
you start your engine and
release the switch. The switch stays
in the
“Run” position when the engine is
running.
But even when the engine is not
running,
you can use “Run” to operate
your electrical power accessories and to
display some instrument panel warning
and indicator lights.
Start (E): Starts the engine. When the
engine starts, release the key. The ignition
switch will return to “Run” for normal
driving.
Note that even if the engine is not
running, “ACC” and “Run’’ allow
you to
operate your electrical accessories, such
as the radio and ventilation fan.
55. .
Page 109 of 292
Downloaded from www.Manualslib.com manuals search engine In this part you’ll find out how to
)perate the comfort control
systems and audio systems
lffered with your Chevrolet
. Be
sure to read about the particular
system supplied with your
rehicle
.
Part 3
Comfort Controls & Audio
Systems
Comfort Controls ................................................ 108
Heatercontrols
............................................... 108
Heating ...................................................... 108
Bi-LevelHeating .............................................. 109
Ventilation
................................................... 109
Defogging and Defrosting Windows
............................... 109
Air Conditioner Controls
........................................ 110
Cooling ...................................................... 110
Rearwindow Defogger
......................................... 111
Audiosystems .................................................. 112
Flow-Through Ventilation System ................................. 111
Settingtheclock .............................................. 113
AMEM Stereo
with Cassette Tape Player ........................... 113
AM/FM Stereo with Compact Disc Player .......................... 116
Understanding Radio Reception .................................. 120
Care of Your Cassette Tape Player
................................. 120
Care of Your Compact Discs ..................................... 121
FixedMastAntenna
............................................ 121
107 ...
Page 114 of 292
Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
Ventilation Tips
D Keep the hood and front air inlet free
of ice, snow, or any other obstruction
(such as leaves). The heater and
defroster will work far better, reducin
the chance of fogging the inside of
your windows.
When
you enter a vehicle in cold
weather, turn the fan control knob to
the right for a few moments before
driving off. This helps clear the intakc
ducts of snow and moisture, and
reduces the chance of fogging the
inside of your windows.
Keep the air path under the front seat:
clear of objects. This helps air to
circulate throughout your vehicle.
.I12
I‘
Audio Systems
Your Delco@ audio system has been
jesigned to operate easily and give years
If listening pleasure. But you will get the
nost enjoyment out of
it if you acquaint
yourself
with it first. Find out what your
Delco@ system can do and how to operate
111 its controls, to be sure you’re getting
:he most out
of the advanced engineering
.hat went into
it.
:f you have power door locks, your
qehicle has a feature called Retained
4ccessory Power (RAP). With RAP you
:an
play your audio system even after the
ignition
is off. See the Index under
“Retained Accessory Power.”
NOTICE:
Before you add any sound equipment
to your vehicle
- like a tape player,
CB radio, mobile telephone or
two-way radio
- be sure you can
add what you want. If you can, it’s
very important
to do it properly.
Added sound equipment may
interfere with the operation of your
vehicle’s engine, Delco@ radio or
other systems, and even damage
them. And, your vehicle’s systems
may interfere with the operation
of
sound equipment that has been added
improperly.
So, before adding sound equipment,
check with your dealer and be sure to
check Federal rules covering mobile
radio and telephone units.
Page 115 of 292
Downloaded from www.Manualslib.com manuals search engine I Setting the Clock
AM/FM Stereo with Cassette Tape
Player
1. Press “SET.”
2. Within five seconds, press and hold
“SEEK
V’’ until the correct hour
appears.
3. Press and hold “SEEK A’’ until the
correct minute appears.
Delco/Bose AM/FM Stereo with Compact Disc Player
1. Press “SET.”
2. Within five seconds, press and hold
“SCAN” until the correct hour
appears.
“SEEK ” until the correct minute
appears.
3. Press and hold “SEEK 4 ” or
I
/ VOL- BAL TREE
PROG-RCL A
1 TUNE- FADE BASS
AM-FMA
\
AMIFM Stereo with Cassette
Tape Player
To Play the Radio
Turn the upper knob to turn the system
on or off.
Volume
Turn the upper knob to adjust the
volume.
AM-FM
Press the lower knob to get AM or FM.
The lighted display shows your
selection.
Tune
Turn the lower knob to choose radio
stations.
Recall
Press the upper knob to recall the
station being played or the clock
display.
Seek
Press “SEEK 7’’ or “SEEK A’7 and
the radio
will tune to the next lower
or higher station and stay there.
113 ...
Page 117 of 292
Downloaded from www.Manualslib.com manuals search engine I
Adjusting the Speakers
Balance:
Turn the balance control behind
the upper knob to move the sound
between the right and left speakers.
Fade: Turn the fade control behind the
lower knob to move the sound between
the front and rear speakers.
The Delco/Bose premium speaker system
only includes three speakers. It does not
include speakers in the panel behind the
grilles
next to the rear seat.
To Play a Cassette Tape
Your tape player is built to work best with
tapes that are 30 to 45 minutes long on
each side. Tapes longer than that are
so
thin they may not work well in this player.
The longer side with the tape visible goes
in first. If you hear nothing or hear just a
garbled
sound, it may not be in squarely.
Press “STOP-EJECT” to remove the tape
and start over.
Once the tape is playing, use the upper
and lower knobs just as you do for the
radio. The arrows show which side of the
tape
is playing. Press
4 or b to
rapidly rewind or advance
the tape. Press “STOP-EJECT” half way
to stop the tape.
Automatic Program Search
When you push “APS” you can go to the
beginning of a new selection.
To go forward to the beginning of the
next selection, press
b .
0 To go back to the beginning of the
current selection, press
4 . Push 4
again to go to the beginning of the
previous selection.
Program
Press the upper knob on your system to
switch from one side of the tape to the
other or to stop the tape from searching.
Your cassette tape player can play
continuously be&use the player has an
auto-reverse feature.
Eject
Press “STOP-EJECT” fully to remove the
tape or stop the tape and switch to the
radio.
CrO2 (Delco/Bose System)
The “CrO2” button lets you set the
system for the type of cassette being used.
If you are using chrome or metal tapes,
push “CrO2” in. If you are using standard
tapes, make sure “CrO2” is out.
Noise Reduction (Delco/Bose System)
Your sound system has the Dolby@
automatic noise reduction feature.
Dolby@ Noise Reduction is manufactured
under license from Dolby Laboratories
Licensing Corporation. “Dolby” and the
00 @ symbol are trademarks of Dolby
Laboratories Licensing Corporation.
115.. .
Page 118 of 292
Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
[ VOLOBAL
POWER
1 TUNE 00 FADE
F
D
R
‘c AM-FM a
COMP RDM REV FWD SCAN PREV NEXT
AM!FM Stereo with Compact
Disc Player
To Play the Radio
Turn the upper knob to turn the system on
or off.
Volume
Turn the upper knob to adjust the volume.
AM-FM
Press the lower knob to get AM, FMl or
FM2.
. . . 116
Tune
Turn the lower knob to choose radio
stations.
Recall
Press “RCL” to reca .I1 the station being
played or the time.
Seek
Press “SEEK 4 ” or “SEEK ” to go to
the next lower
or higher station and stay
there.
Scan
Press “SCAN’ to hear each station for a
few seconds. When you want to stop
scanning, press “SCAN’ again or the
upper knob.
Pushbuttons
The five pushbuttons let you return to
your favorite stations.
To set the
pushbuttons for up to
15 stations (5 AM,
5 FMl and 5 FM2), just:
1. Press the lower knob to choose AM,
2. Tune in the station.
3. Press “SET.” (“SET” will appear on
the display for about five seconds.)
4. Within five seconds, press one of the
pushbuttons. Whenever you press that
button, the preset station
will return.
FMl or FM2.
Page 120 of 292
Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
To Play the Next Selection
Press “NEXT” to hear the next track now
(instead of waiting until
the present track
is finished).
If you press and hold this button or press
it more than once, the disc will advance
further.
To Replay the Current Selection
Press “PREV” to hear a track again.
If you press and hold this button, or press
it more than once, the disc will return to
previous tracks.
Reverse
Press and hold “REV” to rapidly return to
a favorite passage. Release
it to play the
passage.
Fast Forward
Press and hold “FWD’ to quickly
advance within
a track. Release it to
resume playing.
Scan
Press “SCAN” to listen to each track for
about
10 seconds. Press “RDM” or
“SCAN” to stop the scanning.
Compression
Press “COMP’ to make loud and soft
passages more nearly equal
in volume.
Random
Press “RDM” to hear a random selection
of tracks.
To Stop the Disc Player
0
0
0
Turn the power off or turn the ignition
key off. The disc stays
in the player
and will resume playing at the point
where
it stopped.
Press “ST-PL” to stop playing the disc
and switch to radio. Press “ST-PL,” to
restart
the disc at the point where it
stopped.
Press “EJCT” to eject the disc and the
radio
will play. The disc will start
playing
at track 1 when you reinsert it.
Theft-Deterrent Feature
Delco-Loc I1 is a security feature for the
compact disc player.
It can be used or
ignored. If ignored, the system functions
normally. If
it is used, your system won’t
be usable
if it’s ever stolen.
Setting Your Security Code
The instructions below tell you how to
enter a security code into the system. If
your vehicle loses battery power for
any
reason, you must enter the security code
again before the system
will turn on.
1. Write down any six-digit number and
2. Turn the ignition switch to the “Acc”
3. Turn the audio system off.
4. Press and hold pushbuttons “1” and
keep
it in a
safe place.
or
“Run” position.
“4” together until “---” shows on the
display.
You are now ready to enter your security
code. Don’t wait more than
15 seconds
between steps.
. . .118
Page 122 of 292
Downloaded from www.Manualslib.com manuals search engine Comfort Controls and Audio Systems
6. Turn the lower knob until the fifth and
sixth digits
of your code appear,
7. Press the lower knob. The clock
display will appear and the unit will
work. If
“LOC” shows, the numbers
did not match and the unit is still
locked.
How to Change Your Security Code
You can change your security code by
following these steps:
1. Using your old code, follow the
directions given under “Shutting
Off
the Theft-Deterrent Feature.”
2. Repeat directions of “Setting Your
Security Code” with your new
security code.
Understanding Radio Reception
FM Stereo
FM stereo will give you the best sound.
But
FM signals will reach only about
10 to 40 miles (16 to 65 km). And, tall
buildings or hills can interfere with
FM signals, causing the sound to come
and go.
I
AM
The range for most AM stations is greater
than for
FM, especially at night. The
longer range, however, can cause stations
to interfere with each other. AM can pick
up noise from things like storms and
power lines. Try reducing the treble to
reduce this noise if you ever get it.
AM Stereo
This means the Delco@ system can
receive C-QUAM@ stereo broadcasts.
Many
AM stations around the country use
C-QUAM@ to produce stereo, though
some do not. (C-QUAM@
is a registered
trademark of Motorola, Inc.) If your
Delco@ system can get C-QUAM@, your
“STEREO” light will come on when
you’re receiving it.
Care of Your Cassette Tape
Player
A tape player that is not cleaned regularly
can cause reduced sound quality, ruined
cassettes, or a damaged mechanism.
Cassette tapes should be stored in their
cases away from contaminants, direct
sunlight, and extreme heat. If they aren’t,
they may not operate properly or cause
failure of the tape player.
Your tape player should
be cleaned
regularly each month or after every
15
hours of use. If you notice a reduction in
sound quality, try a known good cassette
to see if the tape or the tape player
is at
fault. If this other cassette has no
. . .I20
Page 151 of 292
Downloaded from www.Manualslib.com manuals search engine Jump Starting
If your battery has run down, you may
want to use another vehicle and some
jumper cables to start your Chevrolet. But
please follow the steps below to do it
safely. NOTICE:
Ignoring these steps could result in
costly damage to your vehicle that
wouldn’t be covered by your war-
ranty.
Trying to start your Chevrolet by
pushing or pulling
it could damage
your vehicle, even
if you have a
manual transmission. And if you
have an automatic transmission,
it
won’t start that way.
To Jump Start Your Chevrolet:
1. Check the other vehicle. It must have
a 12-volt battery with a negative
ground system.
NOTICE:
If the other system isn’t a 12-volt
system with a negative ground, both
vehicles can be damaged.
2. Get the vehicles close enough so the
jumper cables can reach, but be sure
the vehicles aren’t touching each other.
If they are,
it could cause a
ground connection you don’t want.
You wouldn’t be able to start your
Chevrolet, and the bad grounding
could damage the electrical systems.
3. Turn off the ignition on both vehicles.
Turn off all lights that aren’t needed,
and radios. This
will avoid sparks and
help save both batteries. And
it could
save your radio!
NOTICE:
If you leave your radio on, it could be’
badly damaged. The repairs wouldn’t
be covered
by your warranty.
4. Open the hoods and locate the
batteries.
149 ...