display CHEVROLET CAMARO 1996 4.G User Guide

Downloaded from www.Manualslib.com manuals search engine Setting the Tone
BASS:
Press the up arrow to hear more bass and the
down arrow to hear less bass. Press the center of the
button for the factory-preset position. BASS will appear
briefly on the display whenever
BASS is pressed.
TREB: Press the up arrow to hear more treble and the
down arrow to hear less treble. Press the center
of the
button for the factory-preset position. TREB will appear
briefly
on the display whenever TREB is pressed.
Adjusting the Speakers
BAL:
Turn the control behind the upper knob to adjust
the sound between the right and left speakers.
FADE: Turn the fade control behind the lower knob to
move the sound between the front and rear speakers.
Playing a Compact Disc
Don’t use the mini-discs (three-inch singles). They
will eject, but they won’t play. Use only full-size
compact discs.
Insert a disc partway into the slot, label side
up. The
player will pull it in. The disc should begin playing.
If you’re driving on a very rough road or if it’s very hot,
the disc may not play and
ERR (error) may appear on the
display. Press RECALL to take
ERR off the display.
When things get back to normal, the disc should play. If
the disc comes out, it could be that:
0 The disc is upside down.
0 It is dirty, scratched or wet.
0 It is very humid. (If so, wait about an hour and
try again.)
RCL: Press this button to see which track is playing.
Press it again within five seconds to see how long
it has
been playing. The track number will also appear on the
display when
you change volume or when a new track
starts playing.
COMP: Press this button to maKe loud and soft
passages more nearly equal
in volume. COMP will
appear
on the display.
RDM: Press this button to hear the tracks in random,
rather than sequential, order.
RDM will appear on
the display. Press this button again to return to
normal sequence.
REV: Press and hold this button to return to a
previously played passage rapidly. Release the button
to play the passage. The counter reading will appear
on
the display.
3-16

Downloaded from www.Manualslib.com manuals search engine 3. Press the 1 and 4 buttons together. Hold them down
until
--- shows on the display. Next you will use the
secret code number which you have written down.
4. Press SET and 000 will appear on the display.
5. Press SCAN to make the first digit of your
code appear.
6. Press the SEEK right or left arrow to make the
second and third digits of your code appear.
7. Press AM-FM and 000 will appear on the display
again.
Now you are ready to enter the last three
digits of your code.
code appear.
two digits
of your code appear,
8. Press SCAN to make the fourth digit of your
9. Press the SEEK right or left arrow to make the last
10. Press AM-FM and REP will appear on the
display for five seconds, and then
000 will appear
on the display.
1 1. For verification, repeat Steps 6 through 11. If SEC
appears on the display, your audio system is
secured. If
--- shows on the display, your system is
not secured.
You must restart the entire procedure
again from
Step 4.
Unlocking the 1
Power Loss
Enter your secret code as follows; pause no more than
15 seconds between steps:
1. Turn the ignition on. (The radio should be
off. LOC
will appear
on the display.)
2. Press SET and 000 will appear on the display.
3. Press the SCAN to make the first digit of your
code appear.
4. Press the SEEK right or left arrow to make the
second and third digits
of your code appear.
5. Press AM-FM and 000 will appear on the display
again. Now you are ready to enter the last three
digits of your code.
6. Press SCAN to make the fourth digit of your
code appear.
7. Press the SEEK right or left arrow to make the last
two digits of your code appear.
8. Press AM-FM. If the time appears, the unlocking
sequence was successful. If the display shows
SEC,
the digits did not match and the unit is still secured.
If you lose or forget your code, contact your dealer.
3-18 -

Downloaded from www.Manualslib.com manuals search engine Disabling the Theft-Deterrent Feature
1.
2.
3.
4.
5.
6.
7.
8.
9.
Turn the ignition on.
Turn the radio off.
Press the 1 and
4 buttons together. Hold them down
until
SEC shows on the display.
Press
SET and 000 will appear on the display.
Press
SCAN to make the first digit of your code appear.
Press the SEEK right or left arrow to make the
second and third digits
of your code appear.
Press AM-FM and
000 will appear on the display
again. Now you are ready to enter the last three
digits of your code.
Enter the last three digits of your code. The display
will show the numbers as entered.
Press AM-FM after you have confirmed that the
code matches
the secret code you have written down.
The display will show
---, indicating that the radio is
no longer secured.
If the code entered is incorrect,
SEC will appear on the
display. The radio will remain secured until the correct
code is entered.
When battery power is given to a secured radio, the
radio won’t turn on and
LOC will appear on the display.
Understanding Radio Reception
FM Stereo
FM stereo will give you the best sound. But FM signals
will reach only about
10 to 40 miles (16 to 65 km). Tall
buildings or hills can interfere with
FM signals, causing
the sound to come and
go.
AM
The range for most AM stations is greater than for FM,
especially at.night. The longer range, however, can
cause stations to interfere with each other. AM can pick
up noise from things like storms and power lines. Try
reducing the treble to reduce this noise if
you ever get it.
Tips About Your Audio System
Hearing damage from loud noise is almost undetectable
until it is too late. Your hearing can adapt
to higher
volumes
of sound. Sound that seems normal can be loud
and harmful to your hearing. Take precautions by
adjusting the volume control on your radio to a safe
sound level before your hearing adapts
to it.
3-19