light CHEVROLET CAMARO 1996 4.G User Guide

Downloaded from www.Manualslib.com manuals search engine Exit Lighting and Delayed Illumination
Your vehicle comes with this feature set in Mode 4. This
means that your interior lamps will go on when the key
is removed from the ignition switch and stay on for
25 seconds after closing the doors to help in exiting the
vehicle. To change the factory setting, do the following:
1.
Turn the courtesy lamps ON by turning the instrument
panel brightness control knob all the way up.
2. Count the number of chimes you hear. The number of
chimes tells you which mode your vehicle is set for.
3. Turn the courtesy lamp switch to OFF.
4. Turn the courtesy lamp switch from ON to OFF until
you hear the number of chimes that correspond to the
mode selection you want.
Mode 1: Both Off (Interior lamps will turn on or off at
the same instant that a door is opened or closed).
Mode 2: Delayed Illumination Only (Interior lamps will
stay
on for 25 seconds after the doors are closed).
Mode 3: Exit Lighting Only (Interior lamps will come
on whenever you remove the ignition key).
Mode 4: Both On (This combines'Mode 2 and 3).
Last Door Closed Locking and
Lockout Prevention
Your vehicle comes with this feature set in Mode 2. This
means that your power door locks will not lock when
the keys are in the ignition and a door is open. To
change the factory setting, do the following:
1. Press the LOCK switch on the door.
2. Count the number of chimes you hear. The number of
chimes tells you which mode your vehicle is set for.
3. Press the LOCK switch on the door until you hear
the number of chimes that correspond to the mode
selection you want.
Mode 1: Both Off (Doors will locldunlock when you
press the power door lock switch).
Mode 2: Lockout Prevention Only (If you leave your keys
in
the ignition and get out the driver's door, you won't be
able to lock the doors with the power door lock switch).
Mode 3: Last Door Closed Locking Only (If the power
door lock switch is used to lock the vehicle while any
door
is open, you will hear three chimes. The doors will
not lock
until after all doors are closed).
Mode 4: Both On (This combines Mode 2 and 3).
2-18

Downloaded from www.Manualslib.com manuals search engine If you have an automatic transmission, the ignition
switch can’t be turned
to LOCK unless the shift lever is
in the PARK
(P) position.
OFF (C): Unlocks the steering wheel, ignition and
automatic transmission, but does not send electrical
power to any accessories. Use this position if your
vehicle must be pushed or towed.
A warning tone will
sound if you open the driver’s door when the ignition is
in
OFF and the key is in the ignition.
RUN (D): Position to which the switch returns after
you start your engine and release the switch. The switch
stays
in the RUN position when the engine is running.
But even when the engine is
not running, you can
use RUN to operate your electrical power accessories
and to display some instrument panel warning and
indicator lights.
START (E): Starts the engine. When the engine starts,
release the key. The ignition switch will return
to RUN
for normal driving.
Note that even if the engine is not running,
ACC and
RUN allow you to operate your electrical accessories,
such as the radio and ventilation fan.
Key Release Button
If you have a manual
transmission, your ignition
lock has a key release
button.
You must press
the button before you
can
take your key out of the
ignition lock.
-1
On manual transmission vehicles, turning the key
to
LOCK will lock the steering column and result
in
a loss of ability to steer the vehicle. This could
cause
a collision. If you need to turn the engine
off while the vehicle is moving, turn the key only
to
OFF. Don’t press the key release button while
the vehicle is moving.
3-32

Downloaded from www.Manualslib.com manuals search engine Skip Shift Light (5.7L LT1 Engine)
SKIP
SHIFT
When this light comes on,
you can only shift from
FIRST
(1) to FOURTH (4)
instead of FIRST (1) to
SECOND (2). This helps
you to get the best possible
fuel economy.
This light will come on under these conditions:
The engine coolant temperature is greater than
170°F (77"C),
You are going 15 to 20 mph (24 to 32 km/h), and
0 You are at 35 percent throttle or less.
When this light is on, the gear shift lever will let you
shift from FIRST
(1) to FOURTH (4) only. Once you
are in
FOURTH (4), you can press the clutch again and
shift into another gear.
Follow the
shift speeds on this chart when the SKIP SHIFT
light is on.
Computer Aided Manual Transmission Shift Speeds:
1st to 4th. . . 15 mph (24 km/h)
4th to
5th . . . 25 mph (40 km/h)*
5th to
6th . . .40 mph (64 km/h)**
Each time you come
to a stop, the engine's Electronic
Control Module (ECM) determines when
to activate the
SKIP SHIFT upshift system. Use SECOND (2) gear
only when
you accelerate very quickly from a stop. You
can then follow the full gear shift pattern.
*30 mph (48 km/h) when accelerating to
highway speeds.
**45 mph (72kmh) when accelerating to
highway speeds.
2-34

Downloaded from www.Manualslib.com manuals search engine Second-Gear Start (Option)
Your vehicle may be quipped with a Second-Gear Start
feature. Press 2ND GEAR START
to provide more
traction when you are starting
on ice or other slippery
surfaces.
The 2ND gear light on the cluster will
illuminate when 2nd gear start is selected. The
transmission will be in SECOND (2) gear when the
vehicle begins to move. After starting in SECOND
(2)
the vehicle will upshift normally.
This feature is
only for improved traction when the road
surface is slippery and
is not intended for continuous
use. Always use NORMAL for normal road conditions.
You may press 2ND GEAR START again to turn off this
feature. Whenever you start your vehicle, the
transmission
is in the NORMAL mode.
Limited-Slip Rear Axle
If you have this feature, your rear axle can give you
additional traction on snow, mud, ice, sand or gravel. It
works like a standard axle most of the time, but when
one
of the rear wheels has no traction and the other does,
the limited-slip feature will allow the wheel
with
traction to move the vehicle.
Parking Brake
To set the parking brake, hold the brake pedal down and
pull up
on the parking brake lever. If the ignition is on,
the brake system warning light will come
on.
2-36

Downloaded from www.Manualslib.com manuals search engine Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the
turn is finished, the lever will return automatically.
An arrow on the instrument
panel will flash in the
direction
of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete
your lane change. The lever will return by
itself when you release it. As
you signal a turn
or a lane change, if the arrows don’t
flash but just stay on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident.
If the arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses and Circuit
Breakers” in the Index).
Headlamp High/Low Beam Changer
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward you.
Then release it.
When
the high beams
are on, this light on the
instrument panel also
will be
on.
2-44

Downloaded from www.Manualslib.com manuals search engine Windshield Wipers
You control the windshield wipers by turning the band
with the wiper symbol on
it.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle. If you want more cycles, hold
the
band on MIST longer. You
can
set the wiper speed for a long or short delay
between wipes. This can be very useful in light rain or
snow. Turn the band to choose the delay time. The
closer
to LO, the shorter the delay.
For steady wiping at low speed, turn the band away
from
you to the LO position. For high-speed wiping,
turn the band further, to
HI. To stop the wipers, move
the band
to OFF.
Damaged wiper blades I'niiy prevent you from seeing
well enough
to drive safely. To avoid damage, be sure to
clear ice and snow from the wipers blades before using
them. If they're frozen
to the windshield, carefully
loosen or thaw them. If your blades
do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers.
A circuit
breaker will stop them until the motor cools. Clear away
snow or ice
to prevent an overload.
2-45

Downloaded from www.Manualslib.com manuals search engine Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:
0 Use the accelerator pedal to get to the higher speed.
Push the button at the end of the lever, then release
the button and the accelerator pedal. You’ll now
cruise at the higher speed.
0 Move the cruise switch from ON to R/A. Hold it
there until
you get up to the speed you want, and
then release the switch.
(To increase your speed in
very small amounts, move the switch to
WA for
less than half
a second and then release it. Each
time you
do this, your vehicle will go about 1 mph
(1.6
km/h) faster.)
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:
Push in the button at the end of the lever until you
reach the lower speed you want, then release it.
To slow down in very small amounts, push the
button for less than half a second. Each time you
do
this, you’ll go 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step
on the
accelerator pedal to maintain your speed. When going
downhill, you may have
to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this
to
be too much trouble and don’t use cruise control on
steep hills.
Ending Out of Cruise Control
There are several ways to turn off the cruise control:
0 Step lightly on the brake pedal or push the clutch
pedal, if
you have a manual transmission ; OR
Move the cruise switch to OFF.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory
is erased.
-9

Downloaded from www.Manualslib.com manuals search engine Lamps
The main lamp control is a knob that works these lamps:
Headlamps
0 Taillamps
Parking Lamps
License Lamps
0 Sidemaricer Lamps
0 Instrument Panel Lights
-’J$
’ I Turn the knob to this position to turn on your
headlamps and other operating lamps.
PC Turn the knob to this position to turn on your
parking lamps without your headlamps
Turn the knob
to OFF to turn off the lamps.
Headlamps On Reminder
If you turn the ignition to the OFF position and leave the
lamps on,
you will hear a chime, lasting up to five
seconds. If the lamps are still
on when you open the
driver’s door, the chime will sound again.
Daytime Running Lamps (Option)
Daytime Running Lamps (DRL) can make it easier for
others to see the front
of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work,
so be sure it isn’t covered.
2-50

Downloaded from www.Manualslib.com manuals search engine $0 To turn the fog lamps on, push the top of the fog
lamp switch. Push the bottom
of the switch to turn the
fog lamps off.
A light on the switch will come on when
the fog lamps are
on.
Interior Lamps
Instrument Panel Brightness Control
Fog lamps will go off whenever your high beams come
on. When the high beams go off, the fog lamps will
come on again.
If your vehicle is equipped with the Vehicle and Content
Theft-DeterrentIAlarm System and your fog lamp
switch is on, the fog lamps may flash, along with the
parking lamps, to indicate operation of the Vehicle
and Content Theft-DeterrenVAlarm System. See
‘Vehicle and Content Theft-DeterrentIAlarm System’’
in the Index.
This switch controls the brightness
of your
instrument panel lights. Turn the switch
to brighten or
dim the lights.
If you turn the switch all the way up,
your courtesy lamps
will come on.
3 c3

Downloaded from www.Manualslib.com manuals search engine Courtesy Lamps
When any door is opened, several interior lamps go on.
These lamps are courtesy lamps. They make it easier for
you to enter and leave your vehicle.
Courtesy lamps include the dome lamp and other lamps
throughout the interior of your vehicle.
To prevent battery rundown, your interior lamps will be
disabled about
10 minutes after the ignition is turned to
the OFF position. The
10 minute timer will be restarted
if you do any
of the following:
1. Turn the ignition on.
2. Open either door.
3. Press any button on your Remote Lock
Control transmitter.
4. Turn the interior lamp switch from OFF to ON.
5. Open the hatch.
Delayed Illumination (Option)
With delayed illumination, when you open a door, your
courtesy lamps will come on and stay
on for 25 seconds
after the doors are closed. The
25 seconds is shortened if
the ignition is turned to the RUN position or if the
power locks are activated.
To turn this feature on or off,
see “Feature Customization” in the Index.
Exit Lighting (Option)
With exit lighting, the interior lamps will come on when
you remove the key from the ignition
to help you see
while exiting the vehicle. To turn this feature on or off,
see “Feature Customization”
in the Index.
2-53