display CHEVROLET CAMARO SS 2010 Owner's Manual

Vehicle
Personalization
The audio system controls are used
to access the personalization menus
for customizing vehicle features.
CONFIG (Conguration):Press
to access the Configuration
Settings Menu.
MENU / SELECT Knob:Press the
center of this knob to enter the
menus and select menu items.
Turn the knob to scroll through
the menus.
0BACK:Press to exit or move
backwards in a menu.Entering the Personalization
Menus
1. Press the CONFIG button to
access the Configuration
Settings menu.
2. Turn the MENU / SELECT knob
to highlight Vehicle Settings.
3. Press the center of the
MENU / SELECT knob to select
the Vehicle Settings menu.
The following list of menu items will
be available:
•Climate and Air Quality
•Comfort and Convenience
•Collision/Detection Systems
•Language
•Lighting
•Power Door Locks
•Remote Lock/Unlock/Start
•Return to Factory SettingsTurn the MENU / SELECT knob to
highlight the menu. Press the knob
to select it. Each of the menus is
detailed in the following information.
Climate and Air Quality
Select the Climate and Air Quality
menu and the following will be
displayed:
•Remote Start Heated Seats
Remote Start Heated Seats
When on, this feature will turn
the heated seats on when using
remote start.
Press the MENU / SELECT knob
when Remote Start Heated Seats is
highlighted. Turn the knob to select
On or Off. Press the knob to confirm
and go back to the last menu.
4-38 Instruments and Controls

Comfort and Convenience
Select the Comfort and
Convenience menu and the
following will be displayed:
•Chime Volume
•Personalization by Driver
Chime Volume
This allows the selection of the
chime volume level.
Press the MENU / SELECT knob
when Chime Volume is highlighted.
Turn the knob to select Normal
or High. Press the knob to confirm
and go back to the last menu.
Personalization by Driver
This allows the selection of if the
personalization settings are specific
to each driver or the same no
matter which key was used to enter
and start the vehicle.Press the MENU / SELECT knob
when Personalization by Driver
is highlighted. Turn the knob
to select On or Off. Press the knob
to confirm and go back to the
last menu.Collision/Detection Systems
Select the Collision/Detection
Systems menu and the following
will be displayed:
•Park Assist
Park Assist
This allows the Ultrasonic Parking
Assist feature to be turned on or off.
Press the MENU / SELECT knob
when Park Assist is highlighted.
Turn the knob to select On or Off.
Press the knob to confirm and
go back to the last menu.
Language
Select the Language menu and the
following will be displayed:
•English
•French
•Spanish
Turn the MENU / SELECT knob to
select the language. Press the
knob to confirm and go back to the
last menu.
Lighting
Select the Lighting menu and the
following will be displayed:
•Exit Lighting
•Vehicle Locator Lights
Instruments and Controls 4-39

Exit Lighting
This allows the selection of how
long the exterior lamps stay on when
leaving the vehicle when it is dark
outside.
Press the MENU / SELECT knob
when Exit Lighting is highlighted.
Turn the knob to select Off,
30 Seconds, 1 Minute, or 2 Minutes.
Press the knob to confirm and go
back to the last menu.
Vehicle Locator Lights
This allows the vehicle locator lights
to be turned on or off.
Press the MENU / SELECT knob
when Vehicle Locator Lights is
highlighted. Turn the knob to select
On or Off. Press the knob to confirm
and go back to the last menu.Power Door Locks
Select Power Door Locks and the
following will be displayed:
•Unlocked Door Anti Lock Out
•Auto Door Unlock
•Delayed Door Lock
Unlocked Door Anti Lock Out
When on, this feature will keep the
driver’s door from locking when
the door is open. If off is selected,
the Delayed Door Lock menu will
be available.
Press the MENU / SELECT knob
when Auto Door Unlock is
highlighted. Turn the knob to select
On or Off. Press the knob to confirm
and go back to the last menu.Auto Door Unlock
This allows selection of which
of the doors will automatically unlock
when the vehicle is shifted into
P (Park) (automatic transmission) or
when the key is removed from
the ignition (manual transmission).
Press the MENU / SELECT knob
when Auto Door Unlock is
highlighted. Turn the knob to select
All Doors, Driver Door, or Off. Press
the knob to confirm and go back to
the last menu.
Delayed Door Lock
When on, this feature will delay the
locking of the doors. If you want to
override the delay you can press the
power door lock on the driver’s door.
Press the MENU / SELECT knob
when Delayed Door Lock is
highlighted. Turn the knob to select
On or Off. Press the knob to confirm
and go back to the last menu.
4-40 Instruments and Controls

Remote Lock/Unlock/Start
Select Remote Lock/Unlock/Start
and the following will be displayed:
•Unlock Feedback (Lights)
•Locking Feedback
•Door Unlock Options
•Remote Vehicle Start
Unlock Feedback (Lights)
When on, the exterior lamps will
flash when unlocking the vehicle
with the RKE transmitter.
Press the MENU / SELECT knob
when Unlock Feedback (Lights)
is highlighted. Turn the knob
to select Flash Lights or Off.
Press the knob to confirm and
go back to the last menu.Locking Feedback
This allows selection of what type of
feedback is given when unlocking
the vehicle with the RKE transmitter.
Press the MENU / SELECT knob
when Locking Feedback is
highlighted. Turn the knob to select
Lights and Horn, Lights Only,
Horn Only, or Off. Press the knob
to confirm and go back to the
last menu.
Door Unlock Options
This allows selection of which
doors will unlock when pressing
the unlock button on the RKE
transmitter.
Press the MENU / SELECT knob
when Door Unlock Options is
highlighted. Turn the knob to select
All Doors or Driver Door Only.
Press the knob to confirm and go
back to the last menu.Remote Vehicle Start
This allows the Remote Vehicle
Start to be turned on or off,
if the vehicle has this feature.
Press the MENU / SELECT knob
when Remote Vehicle Start is
highlighted. Turn the knob to
select On or Off. Press the knob
to confirm and go back to the
last menu.
Return to Factory Settings
Select Return to Factory
Settings to return all of the vehicle
personalization to the default
settings. Turn the knob to select
Yes or No. Press the knob to
confirm and go back to the
last menu.
Instruments and Controls 4-41

Dome Lamps
The dome lamp buttons are located
in the overhead console.
To change the settings, press the
following:
((Off):Turns the lamp off, even
when a door is open.
1(Door):The lamp comes on
automatically when a door is
opened.
'(On):Turns the dome lamp on.
Lighting Features
Entry Lighting
The lamps inside the vehicle come
on when any door is opened. They
stay on about 20 seconds and when
all of the doors have been closed or
the ignition is turned to ON/RUN they
gradually fade out. They also come
on when the unlock symbol button is
pressed on the Remote Keyless
Entry (RKE) system transmitter.
The lamps inside the vehicle stay
on for about 20 seconds after
the key is removed from the ignition
to provide light as you exit.
Theater Dimming
This feature allows for a three to
five second fade out of the courtesy
lamps instead of immediately
turning off.
Battery Load
Management
The vehicle has Electric Power
Management (EPM) that estimates
the battery’s temperature and
state of charge. It then adjusts the
voltage for best performance
and extended life of the battery.
When the battery’s state of charge is
low, the voltage is raised slightly to
quickly bring the charge back up.
When the state of charge is high, the
voltage is lowered slightly to prevent
overcharging. If the vehicle has a
voltmeter gage or a voltage display
on the Driver Information Center
(DIC), you may see the voltage move
up or down. This is normal. If there is
a problem, an alert will be displayed.
The battery can be discharged at
idle if the electrical loads are
very high. This is true for all
vehicles. This is because the
generator (alternator) may not be
spinning fast enough at idle to
produce all the power that is needed
for very high electrical loads.
5-6 Lighting

A high electrical load occurs when
several of the following are on, such
as: headlamps, high beams, fog
lamps, rear window defogger,
climate control fan at high speed,
heated seats, engine cooling fans,
trailer loads, and loads plugged into
accessory power outlets.
EPM works to prevent excessive
discharge of the battery. It does
this by balancing the generator’s
output and the vehicle’s electrical
needs. It can increase engine
idle speed to generate more power,
whenever needed. It can temporarily
reduce the power demands of
some accessories.
Normally, these actions occur in
steps or levels, without being
noticeable. In rare cases at thehighest levels of corrective action,
this action may be noticeable to the
driver. If so, a Driver Information
Center (DIC) message might be
displayed, such as BATTERY
SAVER ACTIVE, BATTERY
VOLTAGE LOW, or LOW BATTERY.
If one of these messages display, it
is recommended that the driver
reduce the electrical loads as much
as possible. SeeDriver Information
Center (DIC) on page 4-27.
Battery Power Protection
This feature shuts off the dome
lamps if they are left on for more than
10 minutes when the ignition is in
LOCK/OFF. This helps to prevent the
battery from running down.
Lighting 5-7

Operation
Controls
The infotainment system is
operated by using the pushbuttons,
multifunction knobs, and menus that
are shown on the display, and
steering wheel controls, if equipped.
Turning the System On or Off
OVOL (Power/Volume):Press to
turn the system on and off.
Automatic Off
If the infotainment system has been
turned on after the ignition is
turned off, the system turns off
automatically after ten minutes.
Volume Control
OVOL (Power/Volume):Turn to
adjust the volume.
PHONE:For vehicles with OnStar
®,
press and hold PHONE to mute
the infotainment system. Press and
hold PHONE again, or turn the
OVOL to cancel mute.
For vehicles without OnStar
®, press
PHONE to mute the infotainment
system. Press PHONE again, or turn
the
OVOL to cancel mute.
Menu System
Controls
The MENU/SELECT knob and the
0BACK button are used to
navigate the menu system.MENU/SELECT:Press to:
•Enter the menu system.
•Select or activate the highlighted
menu option.
•Confirm a set value.
•Switch a system setting on or off.
Turn to:
•Highlight a menu option.
•Select a value.
0BACK:Press to:
•Exit a menu.
•Return from a submenu screen
to the previous menu screen.
•Delete the last character in a
sequence.
6-4 Infotainment System

Radio
AM-FM Radio
Control Buttons
The buttons used to control the
radio are:
RADIO/BAND:Press to turn the
radio on and choose between
AM, FM, and XM™, if equipped.
gSEEK/lSEEK:Press to
search for stations.
FAV:Press to open the
favorites list.
1-6:Press to select preset stations.
MENU/SELECT:Turn to manually
search for stations.
RDS (Radio Data System)
The radio may have RDS. The RDS
feature is available for use only on
FM stations that broadcast RDS
information. This feature only works
when the information from the radio
station is available. In rare cases,
a radio station could broadcast
incorrect information that causes the
radio features to work improperly.
If this happens, contact the radio
station.
While the radio is tuned to an
FM-RDS station, the station name
or call letters display.
Radio Menus
Radio menus are available for AM,
FM and XM, if equipped.Press the MENU/SELECT knob to
open the main radio menu for
that frequency.
Selecting a Band
Press the RADIO/BAND button
to choose AM, FM, or XM™,
if equipped. The last station that
was playing starts playing again.
Selecting a Station
Seek Tuning
Briefly press
gSEEK orlSEEK
to automatically search for the
next available station. If a station is
not found, the radio switches to
a more sensitive search level.
If a station still is not found, the
frequency that was last active
begins to play.
Press and hold
gSEEK or
lSEEK until the station on the
display is reached, then release
the button.
6-8 Infotainment System

Manual Tuning
Turn the MENU/SELECT knob to
select the frequency on the display.
Favorites List
1. Press the MENU/SELECT knob.
2. Select Favorites List.
3. Select the station.
Station Lists
1. Press the MENU/SELECT knob.
2. Select AM or FM Station List.
All receivable stations in the
current reception area are
displayed. If no station list has
been created an automatic
station search is done.
3. Select the station.Updating Station & Category Lists
If stations stored in the station list
can no longer be received.
1. Press the MENU/SELECT knob.
2. Select Update AM or FM
Station List, if the station stored
in the station list are no longer
received. A station search will be
completed and the first station
in the updated list will play.
To cancel the station search, press
the MENU/SELECT knob.
Category Lists
Most stations that broadcast an
RDS PTY code specify the type of
programming transmitted. Some
stations change the PTY code
depending on the content.The system stores the RDS stations,
sorted by program type, in the FM
category list.
To search for a programing type
determined by station:
1. Select FM category list. A list of
all programing types available
displays.
2. Select the programing type.
A list of stations that transmit
programming of the selected
type displays.
3. Select the station.
The category lists are updated when
the corresponding station lists are
updated.
Infotainment System 6-9

XM Categories
XM stations are organized in
categories.
Removing or Adding Categories
1. Press the CONFIG button.
2. Select XM Categories.
3. Turn the MENU/SELECT knob to
highlight the category.
4. Press the MENU/SELECT knob
to remove or add the category.
Selecting an XM Station
XM stations can be selected by
using
gSEEK,lSEEK,
the MENU/SELECT knob, or the
menu system.To select an XM station using
gSEEK orlSEEK, do one of
the following:
•Press and releasegSEEK or
lSEEK to go to the previous
or next station.
•Press and holdgSEEK or
lSEEK to scroll through
the previous or next stations
until the station is reached.
To select an XM station using the
MENU/SELECT knob:
1. Turn the MENU/SELECT knob to
highlight an XM station.
2. Press the MENU/SELECT knob
to select the station, or leave
the station highlighted.
To select a station using the menu:
1. Press the MENU/SELECT knob.
2. Select XM Stations List.
3. Select the station.Selecting a Station by Category
1. Press the MENU/SELECT knob.
2. Select XM Category List.
A list of all programing types
available displays.
3. Select the programing type.
4. Select the station.Storing and Retrieving
Favorites
Stations from all bands can be
stored in any order in the favorite
pages.
Up to six stations can be stored
in each favorite page and the
number of available favorite pages
can be set.
Storing a Station as a Favorite
To store the station to a position
in the list, press and hold the
corresponding 1-6 button until the
station can be heard again.
Infotainment System 6-11