tow CHEVROLET COLORADO 2007 1.G Owners Manual

Seats and Restraint Systems
....................... 7
Front Seats
.............................................. 9
Rear Seats
............................................. 17
Safety Belts
............................................ 20
Child Restraints
...................................... 44
Airbag System
........................................ 77
Restraint System Check
......................... 96
Features and Controls
................................ 99
Keys
..................................................... 101
Doors and Locks
.................................. 106
Windows
............................................... 112
Theft-Deterrent Systems
....................... 115
Starting and Operating Your
Vehicle
.............................................. 118
Mirrors
.................................................. 141OnStar®System
................................... 149
Storage Areas
...................................... 153
Sunroof
................................................ 156
Instrument Panel
....................................... 157
Instrument Panel Overview
................... 160
Climate Controls
................................... 177
Warning Lights, Gages, and
Indicators
.......................................... 181
Driver Information Center (DIC)
............ 198
Audio System(s)
................................... 206
Driving Your Vehicle
................................. 245
Your Driving, the Road, and
Your Vehicle
..................................... 246
Towing
................................................. 299
2007 Chevrolet Colorado Owner ManualM
1

Power Seats
If the vehicle has power
seats, the controls used
to operate them are
located on the outboard
side of the seats.
To adjust the seat, do any of the following:
Move the seat forward or rearward by sliding
the horizontal control forward or rearward.
Raise or lower the front part of the seat
cushion by moving the front of the horizontal
control up or down.
Raise or lower the rear part of the seat
cushion by moving the rear of the horizontal
control up or down.
Raise or lower the entire seat by moving the
entire horizontal control up or down.
Use the vertical control to recline the seatback.
See “Power Reclining Seatbacks” under
Reclining Seatbacks on page 12for more
information.
Manual Lumbar
If your vehicle has
this feature, there is
a knob located on
the outboard side
of the driver’s seat.
Turn the top of the knob toward the front of the
vehicle to increase lumbar support. Turn the
top of the knob toward the rear of the vehicle to
decrease lumbar support.
10

To recline the seatback, do the following:
1. Lift the recline lever.
2. Move the seatback to the desired position,
then release the lever to lock the seatback
in place.
3. Push and pull on the seatback to make
sure it is locked.To return the seatback to an upright position,
do the following:
1. Lift the lever fully without applying pressure to
the seatback and the seatback will return to
the upright position.
2. Push and pull on the seatback to make sure it
is locked.
Power Reclining Seatbacks
If the seats have power
reclining seatbacks,
use the vertical power
seat control located
on the outboard side
of the seat.
To recline the seatback, press the control
toward the rear of the vehicle.
To raise the seatback, press the control
toward the front of the vehicle.
13

Rear Seats
Rear Seat Operation (Extended Cab)
If your vehicle has
an extended cab,
there may be forward
folding seats in the
rear area.
To fold the rear seat cushion(s) from the stored
position to the sitting position, pull the front of
the seat cushion down completely.
The rear seat storage compartments must be
closed before folding the seat down. See
Rear Storage Area on page 154.To store the seat, do the following:
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
1. Secure the safety belt buckle to the inboard side
of the seat with the hook and loop fastener (A),
so that it does not move when not in use.
2. Push the entire seat up until it is ush with the
trim panel.
17

Rear Seat Operation (Crew Cab)
The rear seatback(s) in the crew cab can be
folded forward.
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.To fold the rear seatback(s) forward, do the
following:
1. Disconnect the rear center safety belt latch
from the mini buckle by inserting the tip of
the safety belt tongue into the slot on
the buckle. Let the belt retract.
18

To unlatch the belt, push the button on the buckle.
The belt should go back out of the way. When
the safety belt is not in use, slide the latch plate up
the safety belt webbing. The latch plate should
rest on the stitching on the safety belt, near
the guide loop on the side wall.
Before you close the door, be sure the belt is
out of the way. If you slam the door on it, you
can damage both the belt and your vehicle.
Shoulder Belt Height Adjustment
Before you begin to drive, move the shoulder belt
height adjuster to the height that is right for you.
Adjust the height so that the shoulder portion of the
belt is centered on your shoulder. The belt should
be away from your face and neck, but not falling
off your shoulder. Improper shoulder belt height
adjustment could reduce the effectiveness of the
safety belt in a crash.
To move it up or down,
squeeze the release
buttons (A) together,
or pull them toward
you, and move
the height adjuster to
the desired position.
After you move the height adjuster to where you
want it, try to move it down without squeezing the
release buttons to make sure it has locked into
position.
34

{CAUTION:
Never do this.
Here two children are wearing the same
belt. The belt cannot properly spread the
impact forces. In a crash, the two children
can be crushed together and seriously
injured. A belt must be used by only
one person at a time.
Q:What if a child is wearing a lap-shoulder
belt, but the child is so small that the
shoulder belt is very close to the child’s
face or neck?
A:If the child is sitting in a seat next to a
window, move the child toward the center
of the vehicle. Also seeRear Safety Belt
Comfort Guides on page 40. If the child is
sitting in the center rear seat passenger
position, move the child toward the safety
belt buckle. In either case, be sure that
the shoulder belt still is on the child’s shoulder,
so that in a crash the child’s upper body
would have the restraint that belts provide.
45

Child Restraint Systems
An infant car bed (A), a special bed made for use
in a motor vehicle, is an infant restraint system
designed to restrain or position a child on a
continuous at surface. Make sure that the infant’s
head rests toward the center of the vehicle.A rear-facing infant seat (B) provides restraint
with the seating surface against the back of the
infant. The harness system holds the infant
in place and, in a crash, acts to keep the infant
positioned in the restraint.
50

{CAUTION:
Children can be seriously injured or
strangled if a shoulder belt is wrapped
around their neck and the safety belt
continues to tighten. Secure any unused
safety belts behind the child restraint so
children cannot reach them. Pull the
shoulder belt all the way out of the
retractor to set the lock, if your vehicle
has one, after the child restraint has been
installed. Be sure to follow the instructions
of the child restraint manufacturer.Notice:Contact between the child restraint or
the LATCH attachment parts and the vehicle’s
safety belt assembly may cause damage to
these parts. Make sure when securing unused
safety belts behind the child restraint that
there is no contact between the child restraint
or the LATCH attachment parts and the
vehicle’s safety belt assembly.
Folding an empty rear seat with the safety
belts secured may cause damage to the safety
belt or the seat. When removing the child
restraint, always remember to return the safety
belts to their normal, stowed position before
folding the rear seat.
63

What Makes an Airbag Inate?
In an impact of sufficient severity, the airbag
sensing system detects that the vehicle is
in a crash. The sensing system triggers a
release of gas from the inator, which inates
the airbag. The inator, airbag, and related
hardware are all part of the airbag modules
inside the steering wheel and in the instrument
panel in front of the right front passenger.
For vehicles with roof-mounted side impact
airbags, there are also airbag modules in the
ceiling of the vehicle, near the side windows.
How Does an Airbag Restrain?
In moderate to severe frontal or near frontal
collisions, even belted occupants can contact
the steering wheel or the instrument panel.
In moderate to severe side collisions, even belted
occupants can contact the inside of the vehicle.
Airbags supplement the protection provided
by safety belts. Airbags distribute the force of the
impact more evenly over the occupant’s upper
body, stopping the occupant more gradually.
But the frontal airbags would not help you in
many types of collisions, including rollovers,
rear impacts, and many side impacts, primarily
because an occupant’s motion is not toward
the airbag. Side impact airbags would not
help you in many types of collisions, including
many frontal or near frontal collisions, rollovers,
and rear impacts.
Airbags should never be regarded as anything
more than a supplement to safety belts, and
then only in moderate to severe frontal or
near-frontal collisions for the driver’s and
right front passenger’s frontal airbags, and
only in moderate to severe side collisions for
vehicles with side impact airbags.
85