buttons CHEVROLET OPTRA 5 2007 1.G Owners Manual

Remote Keyless Entry (RKE)
System Operation
The following functions may be available if your
vehicle has the remote keyless entry system.
The LED light (A), on the transmitter, will flash
when the buttons on the remote keyless entry
transmitter are pressed. You can lock and unlock
the vehicle’s doors from about 20 feet (6 m)
away. SeeRemote Keyless Entry (RKE) System
on page 91for additional information.
W(Unlock):Press this button to unlock all of the
doors and the liftgate, if equipped. If all of the
doors and the liftgate are closed, the hazard lamps
will flash twice to indicate that unlocking has
occurred. The theft-deterrent system will deactivate
and the security light will turn off. The security
light is located on the base of the driver’s
door lock.
If a door is not opened or if the engine is not
started within 30 seconds after pressing unlock on
the remote keyless entry transmitter, all of the
doors will automatically lock and the theft-deterrent
system will reactivate.
Q(Lock):Press this button to lock all of the
doors and the liftgate, if equipped. If all of
the doors and the liftgate are closed, the hazard
lamps will flash once and the horn will chirp
to indicate that locking has occurred. The
theft-deterrent system will activate and the security
light will flash.
If the driver’s door is open while pressing lock, all
of the doors, except for the driver’s door will
lock. If any door other than the driver’s door is
open while pressing lock, all of the doors, including
the driver’s door, will lock.
92

S(Panic):If your vehicle has this feature, press
this button to turn on the hazard warning
flashers. The hazard warning lamps will flash for
about 28 seconds. Press this button again to
turn off the hazard warning lamps.
The lock, unlock, and panic buttons, on the
remote keyless entry transmitter, will not operate
while the key is in the ignition. The theft-deterrent
system will not activate while the key is in the
ignition.
Matching Transmitter(s) to Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking
your vehicle. If a transmitter is lost or stolen, a
replacement can be purchased through your
dealer. Remember to bring any remaining
transmitters with you when you go to your dealer.
When the dealer matches the replacement
transmitter to your vehicle, any remaining
transmitters must also be matched. Once your
dealer has coded the new transmitter, the
lost transmitter will not unlock your vehicle.
Each vehicle can have a maximum of four
transmitters matched to it.
Battery Replacement
Under normal use, the battery in the remote
keyless entry transmitter should last about
two years.
The battery is weak if the LED light fails to
illuminate or if the transmitter will not work at the
normal operating range. If you have to get
close to your vehicle before the transmitter works,
it is probably time to change the battery.
Notice:When replacing the battery, use care
not to touch any of the circuitry. Static from
your body transferred to these surfaces
may damage the transmitter.
93

How the System Alarm is Activated
If a door or the trunk or liftgate is opened without
using the key or the remote keyless entry
transmitter, the horn will sound and the lamps will
flash for up to 30 seconds.
How to Turn Off the System Alarm
If the system alarm is active, it can be deactivated
using one of the following methods:
•Press the lock or unlock button on the remote
keyless entry transmitter.
•Unlock the driver’s or passenger’s front door
using the key.
Otherwise, the alarm will automatically stop after
30 seconds. The system will then lock the
doors and reactivate the theft-deterrent system.
How to Detect a Tamper Condition
If the hazard warning lamps flash once when you
press the lock or unlock buttons on the remote
keyless entry transmitter, that means the
theft-deterrent system alarm was triggered while
you were away, from the vehicle.
Starting and Operating
Your Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an
elaborate break-in. But it will perform better in
the long run if you follow these guidelines:
Do not drive at any one constant speed,
fast or slow, for the rst 500 miles
(805 km). Do not make full-throttle starts.
Avoid downshifting to brake, or slow,
the vehicle.
Avoid making hard stops for the rst
200 miles (322 km) or so. During this time
your new brake linings are not yet
broken in. Hard stops with new linings can
mean premature wear and earlier
replacement. Follow this breaking-in
guideline every time you get new brake
linings.
Following break-in, engine speed and load can
be gradually increased.
105

Sunroof
If the vehicle has this feature, the switch is located
between the map lamp buttons. The sunroof will
only operate when the ignition is turned to ON.
The sunroof can be opened to a vent position or it
can be express-opened all of the way.
The sunroof must be manually opened or closed.To open the sunroof to the vent position, push the
front part of the switch. To return the sunroof to
its original position, push the rear part of the switch
and hold it until the sunroof reaches the desired
position.
To fully open the sunroof, push the rear part of the
switch. The sunroof will open automatically until
the front or the rear part of the switch is pushed
again. To close the sunroof, push the front part of
the switch and hold it until the sunroof is closed.
The sunroof will stop if the switch is released
during operation.
In both the vent and fully open positions, the air
flow can be adjusted for driving comfort by pushing
and holding the switch until the sunroof moves
to the desired position.
The sunroof glass panel cannot be opened or
closed if the vehicle has an electrical failure.
131

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on
page 159.
B. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 161.
C. Hazard Warning Flashers Button. SeeHazard
Warning Flashers on page 140.
D. Digital Clock. SeeClock on page 154.
E. Audio System. SeeAudio System(s) on
page 178.
F. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 150.
G. Hood Release. SeeHood Release on
page 257.
H. Exterior Lamps Control. SeeExterior Lamps on
page 148.I. Audio Steering Wheel Controls (If Equipped).
SeeAudio Steering Wheel Controls on
page 202.
J. Horn. SeeHorn on page 140.
K. Cruise Control Buttons. SeeCruise Control on
page 145.
L. Windshield Wiper Control. SeeWindshield
Wipers on page 143.
M. Climate Control System. SeeClimate Control
System on page 155.
N. Ashtray. SeeAshtray(s) and Cigarette Lighter
on page 153.
O. Cigarette Lighter. SeeAshtray(s) and Cigarette
Lighter on page 153.
P. Glove Box. SeeGlove Box on page 126.
139

Clock
Your vehicle has a digital clock. If you have the
wagon, the clock is located in the center of the
instrument panel below the air outlets. If you have a
hatchback, the clock is located in the center of the
instrument panel above the air outlets. When the
ignition is turned to ACC or ON, the time is
displayed in the digital clock. There are
three adjusting buttons for the digital clock:H (Hour):To go forward one hour, press the
H button once. To go forward more than one hour,
press and hold the button until the correct hour
is reached.
M (Minute):To go forward one minute, press
the M button once. To go forward more than
one minute, press and hold the button until the
correct minute is reached.
S (Set):To reset the time to the nearest hour,
press the S button.
For example, if this button is pressed while the
time is between 8:00 and 8:29, the display is set to
8:00. If this button is pressed while the time is
between 8:30 and 8:59, the display is set to 9:00.
After disconnecting the battery or replacing the
fuse, reset the clock.
Hatchback similar
154

AST (Automatic Store)
Six FM1 preset stations with the strongest reception
in the region can be automatically stored. Press the
AST button for more than two seconds. The display
shows AUTO SCANNING and then SCANNING
flashes on the display. Once the stations are stored,
the radio switches to FM1 and the first preset
station begins to play. FM-A displays while listening
to the automatic stored stations. Press the AM or
FM button to cancel automatic store.
Setting Preset Stations
Up to 24 stations (six FM1, six FM2, six AM1, and
six AM2), can be programmed on the six numbered
buttons, by performing the following steps:
1. Turn the radio on.
2. Press the AM or FM button to select FM1,
FM2, AM1 or AM2.3. Tune in the desired station.
4. Press and hold one of the six numbered
buttons for more than two seconds. The
preset button number one through six flashes
on the display when the station has been
set. Whenever that numbered preset button is
pressed, that preset station returns.
5. Repeat the Steps 1 through 4 for each preset
button.
Order of Sound Function
The order for displayed sound function is
BASS, TRE, BAL, FADE, EQ OFF, and VOL
(Bass, Treble, Fade, Balance, Equalization Off,
and Volume).
181

Setting Preset Stations
Up to 36 stations (six FM1, six FM2, six FM-A,
six AM1, six AM2, and six AM-A), can be
programmed on the six numbered buttons, by
performing the following steps:
1. Turn the radio on.
2. Press the AM or FM button to select FM1,
FM2, FM-A, AM1, AM2, or AM-A.
3. Tune in the desired station.
4. Press and hold one of the six numbered
pushbuttons for more than two seconds.
The channel number (CH#1 through CH#6)
flashes on the display when the station
has been set. Whenever that numbered preset
button is pressed, that preset station returns.
5. Repeat the Steps 1 through 4 for each
preset button.
Order of Sound Function
The order for displayed sound function is BASS,
TRE, FAD, BAL, EQ OFF, and VOL (Bass, Treble,
Fade, Balance, Equalization Off, and Volume).
Setting the Tone
(Bass/Midrange/Treble)
SOUND (Bass/Midrange/Treble):Press this
button until BAS (bass) displays. Turn the
power/volume knob to increase or to decrease the
bass. The display shows the bass level. After
making the selection, press this button to select
the bass level.
Press this button until MID (midrange) displays.
Turn the power/volume knob to increase or
to decrease the midrange. The display shows the
midrange level. After making the selection,
press this button to select the midrange level.
Press this button until TRE (treble) displays.
Turn the power/volume knob to increase or to
decrease the treble. The display shows the treble
level. After making the selection, press this
button to select the treble level. If a station is weak
or has static, decrease the treble.
188

Many cleaners contain solvents that may become
concentrated in your vehicle’s breathing space.
Before using cleaners, read and adhere to
all safety instructions on the label. While cleaning
your vehicle’s interior, maintain adequate
ventilation by opening your vehicle’s doors and
windows.
Dust may be removed from small buttons and
knobs using a small brush with soft bristles.
Your dealer has a product for cleaning your
vehicle’s glass. Should it become necessary, you
can also obtain a product from your dealer to
remove odors from your vehicle’s upholstery.
Do not clean your vehicle using the following
cleaners or techniques:
•Never use a knife or any other sharp object to
remove a soil from any interior surface.
•Never use a stiff brush. It can cause damage
to your vehicle’s interior surfaces.
•Never apply heavy pressure or rub
aggressively with a cleaning cloth. Use of
heavy pressure can damage your interior and
does not improve the effectiveness of soil
removal.
•Use only mild, neutral-pH soaps. Avoid laundry
detergents or dishwashing soaps with
degreasers. Using too much soap will leave a
residue that leaves streaks and attracts dirt.
For liquid cleaners, about 20 drops per gallon
(3.78 L) of water is a good guide.
•Do not heavily saturate your upholstery while
cleaning.
•Damage to your vehicle’s interior may result
from the use of many organic solvents such as
naptha, alcohol, etc.
336