light CHEVROLET TRACKER 1993 Repair Manual

Following Distance
Stay at least twice as far behind the
vehicle ahead as you would when
driving your vehicle without a trailer.
This can help you avoid situations that
require heavy braking and sudden turns.
Passing
You’ll need more passing distance up
ahead when you’re towing a trailer.
And, because you’re a good deal longer,
you’ll need to
go much farther beyond
the passed vehicle before you can return
to your lane.
Backing Up
Hold the bottom of the steering wheel
with one hand. Then, to move the trailer
to the left, just move that hand to the
left.
To move the trailer to the right,
move your hand to the right. Always
back up slowly and, if possible, have
someone guide you.
Making Turns
When you’re turning with a trailer,
make wider turns than normal.
Do this
so your trailer won’t strike soft
shoulders, curbs, road signs, trees, or
other objects. Avoid jerky
or sudden
maneuvers. Signal well in advance.
Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle
has to have a different turn signal
flasher and extra wiring. The green
arrows on your instrument panel will
flash whenever you signal
a turn or lane
change. Properly hooked up, the trailer
lights will also flash telling other drivers
you’re about
to turn, change lanes, or
stop.
When towing a trailer, the green arrows
on your instrument panel will flash for
turns even if the bulbs on the trailer are
burned out. Thus, you may think drivers
behind you are seeing your signal when
ProCarManuals.com

Problems on the Road
I Hazard Warning fishers
Your hazard warning flashers let you
warn others. They also let police know
you have a problem. Your front and
rear turn signal lights will flash on and
off.
Press th e button in t :o mak 'our fr 'on t
and rear turn signal lights flash on and
off.
Your hazard warning flashers work no
matter what position your key is in, and
even
if the key isn't in. To turn
again.
off the flashers,
push the switch
When the hazard warning flashers are
on, your turn signals won't work.
Other Warning Devices
If you carry reflective triangles, you can
set one up at the side
of the road about
300 feet (100 m) behind your vehicle.
ProCarManuals.com

3. Turn off the ignition on both
vehicles. Turn
off all lights that
aren’t needed, and radios. This will
avoid sparks and help save both
batteries. And
it could save your
radio!
f you leave your radio on, it
ould be badly damaged.
Thc
?pairs wouldn’i 2 cove--? by
our warrant.
4. Open the hoods and locate the
batteries.
CA UTiON
A An electric fan can start up
- even when the engine is not
running and
can injure you. Keep
hands, clothing and tools away from any underhood electric fan.
Find the positive
(+) and negative
(-) terminals on each battery. Using
a match near
a battery
can cause battery gas to
explode. People
have been hurt
doing this, and some have been
blinded. Use a flashlight if
you
need more light.
Be sure the battery has enough
water. You don’t need to add
water to the Delco Freedom*
battery installed
in every new GM
vehicle. But if a battery has filler
caps, be sure the right amount of
fluid is there. If it is low, add
water
to take care of that first. If
you don’t, explosive gas could be
present.
Battery fluid contains acid that can
burn you. Don’t get
it on you. If
you accidentally get
it in your eyes
or on your skin, flush the place
with water and get medical help
immediately.
ProCarManuals.com

Problems on the Road
Rocking your vehicle to get it out:
First, turn your steering wheel left and
right. That will clear the area around
your front wheels. Then shift back and
forth between
R (Reverse) and a
forward gear (or with a manual
transmission, between First
or Second
gear and Reverse), spinning the wheels
as little as possible. Release the
accelerator pedal while you shift, and
press lightly
on the accelerator pedal
when the transmission is
in gear. If that doesn’t get you
out after a few tries,
you may need to be towed out. Or, you
can use your recovery hooks. If you do
need to be towed out,
see ‘‘Towing
Your Vehicle” in the Index.
-- --
Using the Recovery Hooks
If you ever get stuck in sand, mud, ice,
or snow, your Tracker is equipped with
recovery hooks. The recovery hooks are
provided at the front and rear of your
vehicle. You may need to use them if
you’re stuck off-road and need to be
pulled to some place where you can
continue driving.
ProCarManuals.com

H Checking l7tings under
the Hood
Hood Release
To open the hood, first pull the release
handle inside
the glove box.
Then go to the front of the vehicle, push
down lightly on
the hood, and push the
hood release lever to your left.
Lift the hood, release the hood prop
from its retainer and put the hood prop
into the slot
in the hood.
227 = 9 9
ProCarManuals.com

Service & Appearance Care
How to Check Lubricant:
If the level is below the bottom of the
filler plug hole, you’ll need to add some
lubricant.
If the differential is at operating
temperature (warm), add enough
lubricant to raise the level to the bottom
of the filler plug hole.
If the differential
is cold, add enough
lubricant to raise the level to
1/2 inch
(12 mm) below the filler plug hole.
What to Use:
Refer to the Maintenance Schedule to
determine what kind of lubricant to use.
See “Recommended Fluids and
Lubricants” in the Index.
Engine Coolant
The following explains your cooling
system and how to add coolant when it
is low. If you have a problem with
engine overheating, see “Engine
Overheating” in the Index.
The proper coolant for your Geo will:
Give freezing protection down to
Give boiling protection up to 258°F
Protect against rust and corrosion.
Help keep the proper engine
Let the warning lights work as they
-34°F (-37°C).
(125°C).
temperature. should.
What to Use:
Use a mixture of one-half clean water
(preferably distilled) and one-half
antifreeze or approved recycled coolant
that meets “GM Specification 6038M,”
which won’t damage aluminum parts.
Also use GM Engine Coolant
Supplement (sealer) with a complete
coolant change. If you use these, you
don’t need to add anything else.
ProCarManuals.com

Service & Appearance Care
I- ‘.-I
hdrm .
rn Bulb Replacement I LUU 1 lUIV
~ A Batteries have acid that can
burn you and gas that can
explode.
You can be badly hurt if
you aren’t careful. See
“Jump
Starting” in the Index for tips on
working around a battery without
getting hurt.
L
Contact your dealer to learn how to
prepare your vehicle for longer storage
periods. See “Replacement Bulbs” in the Index
to check
the size and type of bulb you
need to use.
Halogen Bulbs
Halogen bulbs have
pressurized gas inside and can
uurst
if you drop or scratch the
bulb.
You or others could be
injured. Take special care when
handling and disposing
of halogen
bulbs.
Headlights
To replace the headlight bulb:
1. Open the hood.
2. Press down on the tab and pull
rearward, while holding the headlight
wiring harness, to disconnect
it from
the bulb.
ProCarManuals.com

3. Turn the lock ring to the left to
release the bulb.
4. Puli the lock ring and the headlight
bulb straight out. Save the lock ring
and use with the new bulb.
5. Reverse the steps with a new bulb.
Front Parking and Turn Signal Lights
To replace the parking and turn signal
bulb:
1 . Open the hood.
2. Turn the bulb socket to the left and I
pull it out of light housing.
ProCarManuals.com

Service & Appearance Care
3. Push the bulb in, turn it to the left
4. Reverse the steps with a new bulb.
and
pull it out.
Sidemarker Lights
To replace
the sidemarker bulb:
1. Push the sidemarker housing toward
the back
of the vehicle and pull out
the front edge. The housing should
pull away from
the vehicle.
,
i
2. Turn the socket to the left and pull it
3. Pull the bulb out of the socket.
4. Reverse the steps with a new bulb.
Rear Sidemarker Lights
To replace the rear sidemarker bulb:
1. Remove the screw (hardtop only).
2. Pull the sidemarker light housing out
3. Turn the socket to the left and pull it
4. Pull the bulb out of the socket.
5. Reverse the steps with a new bulb.
out
of the
housing.
at the front edge.
out.
ProCarManuals.com

i --
Rear Combination Lights
To remove the rear combination bulbs:
1. Remove the two screws from the
combination lights.
2. Pull the combination light out far
enough to reach the bulb socket. 3. Turn the socket to the left and pull it
4. Pull the bulb out of the socket.
5. Reverse the steps with a new bulb.
out.
251 -
ProCarManuals.com