ignition CHEVROLET TRACKER 2001 2.G User Guide

2-20
Ensure the shift lever is fully in PARK (P) before
starting the engine. Your vehicle has an automatic
transmission shift lock control system. You have to
fully apply your regular brakes before you can shift
from PARK (P) when the ignition key is in ON. If you
cannot shift out of PARK (P), ease pressure on the shift
lever
-- push the shift lever all the way into PARK (P)
and release the shift lever button as you maintain brake
application. Then press the shift lever button and move
the shift lever into the gear you wish. See ªShifting Out
of PARK (P)º in the Index.
REVERSE (R): Use this gear to back up.
NOTICE:
Shifting to REVERSE (R) while your vehicle is
moving forward could damage your transmission.
Shift to REVERSE (R) only after your vehicle
is stopped.
To rock your vehicle back and forth to get out of snow,
ice or sand without damaging your transmission, see
ªStuck: In Sand, Mud, Ice or Snowº in the Index.NEUTRAL (N): In this position, your engine
doesn't connect with the wheels. To restart when you're
already moving, use NEUTRAL (N) only. Also, use
NEUTRAL (N) when your vehicle is being towed.
CAUTION:
Shifting out of PARK (P) or NEUTRAL (N) while
your engine is ªracingº (running at high speed)
is dangerous. Unless your foot is firmly on
the brake pedal, your vehicle could move very
rapidly. You could lose control and hit people
or objects. Don't shift out of PARK (P) or
NEUTRAL (N) while your engine is racing.
NOTICE:
Damage to your transmission caused by shifting
out of PARK (P) or NEUTRAL (N) with the
engine racing isn't covered by your warranty.

2-23 Overdrive-Off Switch (If Equipped)
The overdrive-off switch is located on the left side of
the shift lever. When operating under normal conditions,
the vehicle will automatically default to overdrive when
initially started until it is disengaged. If overdrive is
turned off and the vehicle is turned off, when the vehicle
is restarted, overdrive will automatically turn back on.
By operating the overdrive off switch, with the ignition
switch in the ON position, the four
-speed automatic
transmission (three
-speed plus overdrive) can be
converted to a three
-speed automatic transmission.
While in the three
-speed mode, the transmission
will not shift into the overdrive position.To convert the transmission to the three
-speed mode,
push in the overdrive
-off switch and release it. The
OD/OFF indicator light on the instrument panel cluster
will come on. The overdrive
-off switch is for normal
driving, however, it also offers more power and lower
fuel economy than driving in the overdrive position.
Here are some times you might choose to drive with
the overdrive off switch engaged:

When driving on hilly, winding roads.

When going down a steep hill.
To return the transmission to the four
-speed mode,
push in the overdrive
-off switch again. The OD/OFF
indicator light will go off. Disengaging the overdrive
-off
switch is for normal driving with the four
-speed
automatic transaxle. If you need more power for
passing, and you are:

Going less than about 35 mph (55 km/h),
push your accelerator pedal about halfway down.

Going about 35 mph (55 km/h), push your
accelerator all the way down.
If the transfer case shift lever is in the 4L position,
the four
-speed automatic transmission will remain
in the three
-speed mode.

2-28
Parking Brake
To set the parking brake, hold the brake pedal down and
pull up on the parking brake lever. If the ignition is on,
the brake system warning light will come on.To release the parking brake, hold the brake pedal down.
Pull the parking brake lever up until you can push in
the release button located on the end of the lever.
Hold the release button in as you move the lever all
the way down.
NOTICE:
Driving with the parking brake on can cause
your rear brakes to overheat. You may have to
replace them, and you could also damage other
parts of your vehicle.
If you are towing a trailer, see ªTowing a Trailerº in
the Index.

2-31
Shifting Out of PARK (P)
(Automatic Transmission Only)
Your vehicle has an automatic transmission shift lock
control system. You have to fully apply your regular
brakes before you can shift from PARK (P) when the
ignition is in the ON position. See ªAutomatic
Transmissionº in the Index.
If you cannot shift out of PARK (P), ease pressure on
the shift lever
-- push the shift lever all the way into
PARK (P) and release the shift lever button as you
maintain brake application. Then press the shift lever
button and move the shift lever into the gear you wish
to be in.If you ever hold the brake pedal down but still can't
shift out of PARK (P), try this:
1. Apply the parking brake until the end of Step 6.
2. If the engine is running, turn it off. Turn the key
to ON or ACC.
3. Find the access hole cover on the driver's side of the
console, near the shift lever.

2-32
4. Remove the screw and cover.
5. Inside, you'll see the return plate. Using your finger,
move the return plate toward the rear of the vehicle
until it stops.
6. Move the shift lever into the gear you want.
7. Have the vehicle fixed as soon as possible.
Parking Your Vehicle
(Manual Transmission Models Only)
Before you get out of your vehicle, put your shift lever
in REVERSE (R) and firmly apply the parking brake.
Once the shift lever has been placed into REVERSE (R)
with the clutch pedal pressed in, you can turn the
ignition key to OFF, remove the key and release
the clutch.
If you have four
-wheel drive, be sure your transfer case
is in a drive gear. Your vehicle could roll if it isn't.
If you are towing a trailer, see ªTowing a Trailerº in
the Index.
Parking Over Things That Burn
CAUTION:
Things that can burn could touch hot exhaust
parts under your vehicle and ignite. Don't park
over papers, leaves, dry grass or other things that
can burn.

2-40
Resuming a Set Speed
If you set your cruise control at a desired speed and
then apply the brake, this will turn off the cruise control
function. But you don't need to reset it.
If your speed has not dropped below 25 mph (40 km/h),
you can turn the lever to RESUME ACCEL for about
one second. You'll go right back to your chosen speed
and stay there. When your speed drops below 25 mph
(40 km/h), the system will not resume to your
previously chosen speed. You must reset your speed.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed.

Use the accelerator pedal to go to a higher speed.
Turn the lever to COAST SET and release. Take
your foot off the accelerator pedal. You'll now
cruise at the higher speed.

Turn the lever to RESUME ACCEL. Hold the lever
at RESUME ACCEL until you get up to the speed
you want, then release the lever.
Reducing Speed While Using Cruise Control
To reduce your speed, turn and hold the lever in the
COAST SET position until you reach the lower speed
you want, then release the lever.Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear to
keep your speed down. Of course, applying the brake takes
you out of cruise control. Many drivers find this to be too
much trouble and don't use cruise control on steep hills.
Getting Out of Cruise Control
There are three ways to turn off cruise control:

Step lightly on the brake pedal, or push the clutch
pedal if you have a manual transmission.

Push in the CANCEL button on the end of the
cruise control lever.

Press the CRUISE CTRL. switch on the
instrument panel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.

2-41
Exterior Lamps
Turn the outside part of the lever to control the lamps.
There are three positions for the lamp switch.
Parking Lamps
: This position will turn on the following:

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamp
Headlamps
: This position will turn on the following:

Headlamps

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamp
Turn the switch to OFF to turn off the lamps.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day. DRL
can be helpful in many different driving conditions, but
they can be especially helpful in the short periods after
dawn and before sunset. Fully functional daytime running
lights are required on all vehicles first sold in Canada.
The DRL system will make your headlamps come
on at a reduced brightness when the three following
conditions are met:

The ignition is on with the engine running,

the headlamp switch is off or the parking lights are
on, and

the parking brake is released.

2-42
When the DRL are on, only your headlamps will be on
at a reduce brightness. The taillamps, sidemarker and
other lamps won't be on. Your instrument panel won't
be lit up either.
When you turn on the headlamp switch, your DRL will
go off and your headlamps will come on. The other
lamps that come on with your headlamps will also
come on.
When it begins to get dark, the headlamps will
automatically switch from DRL to the regular
headlamps. See ªAutomatic Light Controlº following.
When you turn the headlamp switch to off, the regular
lamps will go off and your headlamps will change to
the reduced brightness of DRL provided it is not dark
outside. DRL will also come on if only the parking
lamps are being used.
To idle your vehicle with the DRL off, set the parking
brake. The DRL will stay off until you release the
parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.Automatic Light Control (ALC)
Your vehicle is equipped with an automatic light sensor
on top of the instrument panel, so be sure it is not covered.
If it is, the headlamps will remain on continuously.
There is a delay in the transition between the daytime and
nighttime operation of the DRL and the ALC systems so
that driving under bridges or bright overhead street lights
does not affect the system. The DRL and ALC systems
will only be affected when the light sensor sees a change
in lighting lasting longer than this delay.
When it is dark enough outside, or you are driving through
a parking garage, heavy overcast weather or a tunnel, the
ALC will turn on your low
-beam headlamps at normal
brightness. Along with your vehicle's headlamps, the
taillamps, sidemarker, parking lamps and the instrument
panel lights will also turn on. The radio lights will dim.
When the vehicle is initially started in darkness with the
parking brake engaged, there is a delay before the ALC
will turn on the lights.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Lamps On Reminder
If you turn the ignition off, remove the key, open the
door and leave the lamps on, a tone will remind you to
turn off your lamps.

2-43
Interior Lamps
Instrument Panel Brightness Control
The thumbwheel controls
the brightness of your
instrument panel lights.
Turn the wheel upward
to brighten the lights or
downward to dim them.
Dome Lamp
The dome lamp has a three-position switch.
OFF: This position is to the left when you are sitting
in the driver's seat. The lamp will stay off even when
a door is opened.
CENTER: This is the center position. The lamp will
come on when a door is opened. The lamp will turn
off 15 seconds after the last door is closed or when
the ignition key is turned to ON.ON: This position is to the right when you are sitting
in the driver's seat. The dome lamp will turn on and stay
on whether or not a door is open.Battery Rundown Protection
Your vehicle is equipped with a battery saver feature
designed to protect your vehicle's battery.
When the dome lamp or optional luggage compartment
lamp is left on and the ignition is turned off and the key
is removed, the battery saver system will automatically
turn the lamp off after about 15 minutes. This will avoid
draining the battery. This system does not protect
against leaving on the headlamps or parking lamps.

2-44
Mirrors
Inside Day/Night Rearview Mirror
An inside rearview mirror is attached to your windshield.
The mirror can be adjusted up and down or side to side.
The mirror is also equipped with reading lamps and
map lamps.
The mirror can also be adjusted for day or night driving.
Pull the tab for night driving to reduce glare. Push the
tab for daytime driving.
Outside Manual Adjust Mirrors
Adjust these mirrors by hand so that you can just
see the side of your vehicle when you are sitting in a
comfortable driving position.
Power Remote Control Mirrors
(If Equipped)
The switch to control the
power mirrors is located on
the lower left side of the
instrument panel.
You can only adjust the mirrors when the ignition switch
is in ON or ACC.