manual transmission CHEVROLET TRACKER 2001 2.G Owners Manual

Table of Contents
Windows
Keys and Door Locks
Remote Keyless Entry System (If Equipped)
Tailgate
Automatic Transmission (If Equipped)
Manual Transmission (If Equipped)
Four-Wheel Drive (If Equipped)
Parking Brake
Tilt WheelTurn Signal/Multifunction Lever
Windshield Wipers
Cruise Control (If Equipped)
Exterior and Interior Lamps
Mirrors
Storage Compartments
Cargo Cover/Luggage Carrier (Option)
Accessory Power Outlet
Instrument Panel, Warning Lights and Gages Seats and Seat Controls
Safety BeltsAir Bag Systems
Restraint Systems for Children
Section
1
Section
2
Seats and Restraint Systems
Features and Controls
ii

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-4 Keys
2
-6 Door Locks
2
-9 Remote Keyless Entry System (If Equipped)
2
-13 Tailgate
2
-13 Theft
2
-14 New Vehicle ªBreak-Inº
2
-15 Ignition Positions
2
-16 Starting Your Engine
2
-18 Engine Coolant Heater (If Equipped)
2
-19 Automatic Transmission Operation
2
-24 Manual Transmission Operation
2
-26 Four-Wheel Drive (If Equipped)
2
-28 Parking Brake
2
-29 Shifting Into PARK (P)
(Automatic Transmission Only)
2
-31 Shifting Out of PARK (P)
(Automatic Transmission Only)2
-32 Parking Your Vehicle
(Manual Transmission Models Only)
2
-32 Parking Over Things That Burn
2
-33 Engine Exhaust
2
-33 Running Your Engine While You're Parked
(Automatic Transmission)
2
-35 Turn Signal/Multifunction Lever
2
-41 Exterior Lamps
2
-43 Interior Lamps
2
-44 Mirrors
2
-45 Storage Compartments
2
-52 Ashtrays and Cigarette Lighter
2
-52 Sun Visors
2
-53 Accessory Power Outlet
2
-54 Convertible Top (If Equipped)
2
-62 The Instrument Panel -- Your
Information System
2
-64 Instrument Panel Cluster
2
-66 Warning Lights, Gages and Indicators

2-15
Ignition Positions
With the key in the ignition
switch, you can turn the
switch to four positions.
LOCK (A): This is the only position from which you
can remove the key. This locks your steering wheel,
ignition and automatic transmission.
If you have an automatic transmission, the ignition
switch can't be turned to LOCK unless the shift lever
is in PARK (P).CAUTION:
On manual transmission vehicles, turning the key
to LOCK will lock the steering column and result
in a loss of ability to steer the vehicle. This could
cause a collision. If you need to turn the engine
off while the vehicle is moving, turn the key only
to ACC. Don't push the key in while the vehicle
is moving.
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key;
if so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. But turn the key only with your hand.
Using a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.

2-16
ACC (ACCESSORY) (B): This is the position in
which you can operate your electrical power accessories.
It also unlocks the steering wheel and ignition. Use this
position if your vehicle must be pushed or towed.
ON (C): This is the position that the switch returns
to after you start your engine and release the switch.
The switch stays in ON when the engine is running.
But even when the engine is not running, you can use
ON to operate your electrical power accessories and to
display some instrument panel cluster warning and
indicator lights.
START (D): This is the position that starts the engine.
When the engine starts, release the key. The ignition
switch will return to ON for normal driving.
When the engine is not running, ACC and ON allow you
to operate your electrical accessories, such as the radio.
A warning tone will sound if you open the driver's door
when the ignition is in ACC or LOCK and the key is in
the ignition.Starting Your Engine
Automatic Transmission
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's a
safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
NOTICE:
Don't try to shift to PARK (P) if your vehicle
is moving. If you do, you could damage the
transmission. Shift to PARK (P) only when
your vehicle is stopped.
Manual Transmission
The gear selector should be in NEUTRAL and the
parking brake engaged. Hold the clutch pedal to the
floor and start the engine. Your vehicle won't start if
the clutch pedal is not all the way down
-- that's a
safety feature.

2-24 Power Mode Selector Switch
A power mode selector
switch is included
with the four
-speed
automatic transmission.
When you need more power for climbing hills or quicker
acceleration, press the ªPº (power) switch. The POWER
indicator light on the instrument panel cluster will come
on. For normal driving, press the ªNº (normal) switch.
The POWER indicator light will go off.
The power mode delays the automatic transmission shift
points to allow for higher engine speeds in each gear.
The automatic transmission also has the ability to
provide SECOND (2) gear starts for improved
traction on slippery surfaces.The power mode selector switch must be in the P (power)
mode and the transmission gear selector in SECOND (2),
which will remain in SECOND (2) until you shift the
vehicle to DRIVE (D).Manual Transmission Operation
5-Speed
This is your shift pattern.
Here's how to operate
your transmission:
FIRST (1): Press the clutch pedal and shift into
FIRST (1). Then, slowly let up on the clutch pedal
as you press the accelerator pedal.
You can shift into FIRST (1) when you're going less
than 20 mph (32 km/h). If you've come to a complete
stop and it's hard to shift into FIRST (1), put the shift
lever in NEUTRAL and let up on the clutch. Press the
clutch pedal back down. Then shift into FIRST (1).

2-27
TWO-WHEEL HIGH (2H): This setting is for driving
in most street and highway situations. Your front axle is
not engaged in two
-wheel drive.
FOUR
-WHEEL HIGH (4H): This setting
engages your front axle to help drive your vehicle.
Use FOUR
-WHEEL HIGH (4H) when you need
extra traction, such as on wet or icy roads, or in most
off
-road situations.
NEUTRAL (N): Shift to this setting only when your
vehicle needs to be towed.
CAUTION:
Shifting the transfer case to NEUTRAL can
cause your vehicle to roll even if the transmission
is in PARK (P), or if you have a manual
transmission, even if you are in gear. You or
someone else could be seriously injured. Be sure
to set the parking brake before placing the
transfer case in NEUTRAL. See ªParking Brakeº
in the Index.
FOUR-WHEEL LOW (4L): This setting also engages
your front axle to give you extra traction and can be
used for driving downhill, uphill or on rocky terrain
when you're driving slower than 35 mph (55 km/h).
Remember that driving in FOUR
-WHEEL HIGH (4H)
or FOUR
-WHEEL LOW (4L) may reduce fuel
economy. Also, driving in four
-wheel drive on dry
pavement could cause your tires to wear faster and make
your transfer case harder to shift.
You can shift from TWO
-WHEEL HIGH (2H) to
FOUR
-WHEEL HIGH (4H) or from FOUR-WHEEL
HIGH (4H) to TWO
-WHEEL HIGH (2H) at any speed
if your vehicle is going less than 60 mph (100 km/h) and
your wheels are straight ahead. Your front axle will
engage faster if you take your foot off the accelerator
pedal for a few seconds as you shift.
Shifting Into or Out of FOUR
-WHEEL LOW (4L)
1. Stop your vehicle and shift your transmission
to NEUTRAL (N).
2. Shift the transfer case in one continuous motion.
Don't pause in NEUTRAL (N) as you shift from
FOUR
-WHEEL-LOW (4L) to FOUR-WHEEL
HIGH (4H), or your gears could clash.

2-32
4. Remove the screw and cover.
5. Inside, you'll see the return plate. Using your finger,
move the return plate toward the rear of the vehicle
until it stops.
6. Move the shift lever into the gear you want.
7. Have the vehicle fixed as soon as possible.
Parking Your Vehicle
(Manual Transmission Models Only)
Before you get out of your vehicle, put your shift lever
in REVERSE (R) and firmly apply the parking brake.
Once the shift lever has been placed into REVERSE (R)
with the clutch pedal pressed in, you can turn the
ignition key to OFF, remove the key and release
the clutch.
If you have four
-wheel drive, be sure your transfer case
is in a drive gear. Your vehicle could roll if it isn't.
If you are towing a trailer, see ªTowing a Trailerº in
the Index.
Parking Over Things That Burn
CAUTION:
Things that can burn could touch hot exhaust
parts under your vehicle and ignite. Don't park
over papers, leaves, dry grass or other things that
can burn.

2-38
Rear Window Wiper/Washer (If Equipped)
To turn on your rear wiper,
push the upper button.
Push the same button
again to turn it off.
To spray washer fluid on the rear window, push the
lower button about halfway down. Washer fluid will
spray as long as you hold this button. To wash and
wipe at the same time, push the button all the way in.
The washer and wiper will run as long as you hold this
button. To add washer fluid, see ªWindshield Washer
Fluidº in the Index.
Cruise Control (If Equipped)
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot
on the accelerator. This can really help on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, or push the clutch pedal
if you have a manual transmission, the cruise control
turns off.

2-40
Resuming a Set Speed
If you set your cruise control at a desired speed and
then apply the brake, this will turn off the cruise control
function. But you don't need to reset it.
If your speed has not dropped below 25 mph (40 km/h),
you can turn the lever to RESUME ACCEL for about
one second. You'll go right back to your chosen speed
and stay there. When your speed drops below 25 mph
(40 km/h), the system will not resume to your
previously chosen speed. You must reset your speed.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed.

Use the accelerator pedal to go to a higher speed.
Turn the lever to COAST SET and release. Take
your foot off the accelerator pedal. You'll now
cruise at the higher speed.

Turn the lever to RESUME ACCEL. Hold the lever
at RESUME ACCEL until you get up to the speed
you want, then release the lever.
Reducing Speed While Using Cruise Control
To reduce your speed, turn and hold the lever in the
COAST SET position until you reach the lower speed
you want, then release the lever.Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear to
keep your speed down. Of course, applying the brake takes
you out of cruise control. Many drivers find this to be too
much trouble and don't use cruise control on steep hills.
Getting Out of Cruise Control
There are three ways to turn off cruise control:

Step lightly on the brake pedal, or push the clutch
pedal if you have a manual transmission.

Push in the CANCEL button on the end of the
cruise control lever.

Press the CRUISE CTRL. switch on the
instrument panel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.

4-22
Q:What should I do if my vehicle stalls, or is about
to stall, and I can't make it up the hill?
A:If this happens, there are some things you should
do, and there are some things you must not do.
First, here's what you should do:

Push the brake pedal to stop the vehicle and keep
it from rolling backwards. Also, apply the
parking brake.

If your engine is still running, shift the transmission
to REVERSE (R), release the parking brake, and
slowly back down the hill in REVERSE (R).

If your engine has stopped running, you'll need to
restart it. With the brake pedal pressed and the
parking brake still applied, shift the transmission to
PARK (P) (or, shift to NEUTRAL (N) if your
vehicle has a manual transmission) and restart the
engine. Then, shift to REVERSE (R), release the
parking brake, and slowly back down the hill as
straight as possible in REVERSE (R).
As you are backing down the hill, put your left hand
on the steering wheel at the 12 o'clock position. This
way, you'll be able to tell if your wheels are straight
and maneuver as you back down. It's best that you
back down the hill with your wheels straight rather
than in the left or right direction. Turning the wheel
too far to the left or right will increase the possibility
of a rollover.
Here are some things you must not do if you stall, or are
about to stall, when going up a hill.

Never attempt to prevent a stall by shifting into
NEUTRAL (N) (or depressing the clutch, if you
have a manual transmission) to ªrev
-upº the engine
and regain forward momentum. This won't work.
Your vehicle will roll backwards very quickly and
you could go out of control.
Instead, apply the regular brake to stop the vehicle.
Then apply the parking brake. Shift to
REVERSE (R), release the parking brake, and
slowly back straight down.

Never attempt to turn around if you are about to stall
when going up a hill. If the hill is steep enough to
stall your vehicle, it's steep enough to cause you to
roll over if you turn around. If you can't make it up
the hill, you must back straight down the hill.