instrument panel CHEVROLET TRACKER 2001 2.G User Guide

2-24 Power Mode Selector Switch
A power mode selector
switch is included
with the four
-speed
automatic transmission.
When you need more power for climbing hills or quicker
acceleration, press the ªPº (power) switch. The POWER
indicator light on the instrument panel cluster will come
on. For normal driving, press the ªNº (normal) switch.
The POWER indicator light will go off.
The power mode delays the automatic transmission shift
points to allow for higher engine speeds in each gear.
The automatic transmission also has the ability to
provide SECOND (2) gear starts for improved
traction on slippery surfaces.The power mode selector switch must be in the P (power)
mode and the transmission gear selector in SECOND (2),
which will remain in SECOND (2) until you shift the
vehicle to DRIVE (D).Manual Transmission Operation
5-Speed
This is your shift pattern.
Here's how to operate
your transmission:
FIRST (1): Press the clutch pedal and shift into
FIRST (1). Then, slowly let up on the clutch pedal
as you press the accelerator pedal.
You can shift into FIRST (1) when you're going less
than 20 mph (32 km/h). If you've come to a complete
stop and it's hard to shift into FIRST (1), put the shift
lever in NEUTRAL and let up on the clutch. Press the
clutch pedal back down. Then shift into FIRST (1).

2-35
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:

Turn and Lane Change Signals

Headlamp High/Low
-Beam Changer

Flash
-to-Pass
Turn Signal and Lane Change Indicator
The turn signal has an upward (for right) and a
downward (for left) position. These positions allow
you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or a lane change, if the arrows don't
flash but just stay on, a signal bulb may be burned out
and other drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don't go on at all when you
signal a turn, check the fuse (see ªFuses and Circuit
Breakersº in the Index) and for burned
-out bulbs.

2-36 Headlamp High/Low-Beam Changer
First, you must have the headlamps on. For high beams,
push the turn signal lever toward the instrument panel.
When the high beams are
on, a light on the instrument
panel cluster also will be on.
It will go off when you
switch to low beam.
To switch back to low beams, pull the lever toward you.
Flash-to-Pass
With the lever in the low-beam position, pull the lever
toward you to momentarily switch to high beam (to
signal that you are going to pass). When you release the
lever, the headlamps will return to low
-beam operation.
Windshield Wipers
The lever on the right side of the steering column
controls the windshield wipers and washers.
You control the windshield wipers by moving the stalk
up or down.
For steady wiping at low speed, move the stalk down
to LO. For higher speed wiping, move the stalk down
further to HI. To stop the wiper, move the stalk to OFF.

2-39
CAUTION:

Cruise control can be dangerous where
you can't drive safely at a steady speed.
So, don't use your cruise control on
winding roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control.
Don't use cruise control on slippery roads.
Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Press the CRUISE
CTRL. switch on the
instrument panel to turn
the system on. The
indicator light in the
switch will come on.
2. Get up to the speed you want.
3. Once you're going 25 mph (40 km/h) or more,
turn the lever, to COAST SET and release.
Your cruise will set.
4. Take your foot off the accelerator pedal.

2-40
Resuming a Set Speed
If you set your cruise control at a desired speed and
then apply the brake, this will turn off the cruise control
function. But you don't need to reset it.
If your speed has not dropped below 25 mph (40 km/h),
you can turn the lever to RESUME ACCEL for about
one second. You'll go right back to your chosen speed
and stay there. When your speed drops below 25 mph
(40 km/h), the system will not resume to your
previously chosen speed. You must reset your speed.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed.

Use the accelerator pedal to go to a higher speed.
Turn the lever to COAST SET and release. Take
your foot off the accelerator pedal. You'll now
cruise at the higher speed.

Turn the lever to RESUME ACCEL. Hold the lever
at RESUME ACCEL until you get up to the speed
you want, then release the lever.
Reducing Speed While Using Cruise Control
To reduce your speed, turn and hold the lever in the
COAST SET position until you reach the lower speed
you want, then release the lever.Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear to
keep your speed down. Of course, applying the brake takes
you out of cruise control. Many drivers find this to be too
much trouble and don't use cruise control on steep hills.
Getting Out of Cruise Control
There are three ways to turn off cruise control:

Step lightly on the brake pedal, or push the clutch
pedal if you have a manual transmission.

Push in the CANCEL button on the end of the
cruise control lever.

Press the CRUISE CTRL. switch on the
instrument panel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.

2-41
Exterior Lamps
Turn the outside part of the lever to control the lamps.
There are three positions for the lamp switch.
Parking Lamps
: This position will turn on the following:

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamp
Headlamps
: This position will turn on the following:

Headlamps

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamp
Turn the switch to OFF to turn off the lamps.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day. DRL
can be helpful in many different driving conditions, but
they can be especially helpful in the short periods after
dawn and before sunset. Fully functional daytime running
lights are required on all vehicles first sold in Canada.
The DRL system will make your headlamps come
on at a reduced brightness when the three following
conditions are met:

The ignition is on with the engine running,

the headlamp switch is off or the parking lights are
on, and

the parking brake is released.

2-42
When the DRL are on, only your headlamps will be on
at a reduce brightness. The taillamps, sidemarker and
other lamps won't be on. Your instrument panel won't
be lit up either.
When you turn on the headlamp switch, your DRL will
go off and your headlamps will come on. The other
lamps that come on with your headlamps will also
come on.
When it begins to get dark, the headlamps will
automatically switch from DRL to the regular
headlamps. See ªAutomatic Light Controlº following.
When you turn the headlamp switch to off, the regular
lamps will go off and your headlamps will change to
the reduced brightness of DRL provided it is not dark
outside. DRL will also come on if only the parking
lamps are being used.
To idle your vehicle with the DRL off, set the parking
brake. The DRL will stay off until you release the
parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.Automatic Light Control (ALC)
Your vehicle is equipped with an automatic light sensor
on top of the instrument panel, so be sure it is not covered.
If it is, the headlamps will remain on continuously.
There is a delay in the transition between the daytime and
nighttime operation of the DRL and the ALC systems so
that driving under bridges or bright overhead street lights
does not affect the system. The DRL and ALC systems
will only be affected when the light sensor sees a change
in lighting lasting longer than this delay.
When it is dark enough outside, or you are driving through
a parking garage, heavy overcast weather or a tunnel, the
ALC will turn on your low
-beam headlamps at normal
brightness. Along with your vehicle's headlamps, the
taillamps, sidemarker, parking lamps and the instrument
panel lights will also turn on. The radio lights will dim.
When the vehicle is initially started in darkness with the
parking brake engaged, there is a delay before the ALC
will turn on the lights.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Lamps On Reminder
If you turn the ignition off, remove the key, open the
door and leave the lamps on, a tone will remind you to
turn off your lamps.

2-43
Interior Lamps
Instrument Panel Brightness Control
The thumbwheel controls
the brightness of your
instrument panel lights.
Turn the wheel upward
to brighten the lights or
downward to dim them.
Dome Lamp
The dome lamp has a three-position switch.
OFF: This position is to the left when you are sitting
in the driver's seat. The lamp will stay off even when
a door is opened.
CENTER: This is the center position. The lamp will
come on when a door is opened. The lamp will turn
off 15 seconds after the last door is closed or when
the ignition key is turned to ON.ON: This position is to the right when you are sitting
in the driver's seat. The dome lamp will turn on and stay
on whether or not a door is open.Battery Rundown Protection
Your vehicle is equipped with a battery saver feature
designed to protect your vehicle's battery.
When the dome lamp or optional luggage compartment
lamp is left on and the ignition is turned off and the key
is removed, the battery saver system will automatically
turn the lamp off after about 15 minutes. This will avoid
draining the battery. This system does not protect
against leaving on the headlamps or parking lamps.

2-44
Mirrors
Inside Day/Night Rearview Mirror
An inside rearview mirror is attached to your windshield.
The mirror can be adjusted up and down or side to side.
The mirror is also equipped with reading lamps and
map lamps.
The mirror can also be adjusted for day or night driving.
Pull the tab for night driving to reduce glare. Push the
tab for daytime driving.
Outside Manual Adjust Mirrors
Adjust these mirrors by hand so that you can just
see the side of your vehicle when you are sitting in a
comfortable driving position.
Power Remote Control Mirrors
(If Equipped)
The switch to control the
power mirrors is located on
the lower left side of the
instrument panel.
You can only adjust the mirrors when the ignition switch
is in ON or ACC.

2-45
To adjust the mirrors do the following:
1. Move the selector switch to the L (left) or R (right)
to select the mirror you wish to adjust.
2. Press the outer part of the control pad that coincides
with the direction you want the mirror to go.
3. Return the selector switch to the center position to
help prevent moving the mirror accidentally.
Convex Outside Mirror
Your passenger's side mirror is convex. A convex
mirror's surface is curved so you can see more from
the driver's seat.
CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over your shoulder
before changing lanes.
Storage Compartments
Glove Box
To open the glove box, pull the latch toward you.
Use your key to lock and unlock the glove box.
The glove box has a two
-position detent for opening the
door. Lower the door to the first detent for access to the
glove box. Pull it to the next detent for further access.
Door Storage
Each side door has a storage compartment.
Coinholder
Your instrument panel has two coinholders located to
the left of the steering wheel.
Cupholder
Two cupholders are on the center console next to the
parking brake lever.