seats CHEVROLET UPLANDER 2007 1.G User Guide

4. Release the rear set
of seat hooks from
the oor pins by
pulling the
nylon strap, located
at the base of
the seat. Use the
strap to guide
the seat forward.
To return the seat to the original position, do the
following:
1. Align the seat so that the rear hooks on the
seat are over the rear oor pins. Push down
rmly on the rear of the seat so that the
rear hooks attach to the rear oor pins.
2. Try to raise the seat to check that it is locked
to the oor.3. Pull the nylon strap, located on the rear right
hand side of the seat, or lift the recline lever,
located on the front right hand side of the
seatback, to raise the seatback to the upright
position.
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
4. Push and pull on the seatback to check that it
is locked.
One of the bucket seats may be equipped with a
built-in child restraint. SeeBuilt-In Child
Restraint on page 85.
15

Adjusting the Bucket Seats Forward
and Rearward
There are two adjustment levers on the second
row bucket seats that enable them to move
forward or rearward.
One is located below the front of the seat.The other lever is
located on the rear of
the seat.
To adjust the second row bucket seats forward or
rearward, do the following:
1. Lift up either lever and slide the seat forward
or rearward.
2. Release the lever when the seat is in the
desired position.
3. Push and pull on the seat to make sure it is
locked.
16

To recline the seatback, do the following:
1. Pull the nylon strap or lift the recline lever.
2. Press back on the seatback until it is in
the desired position
3. Let go of the strap or lever.
Removing the Bucket Seats
To remove the bucket seats, do the following:
1. Make sure the head restraint is in the
fully lowered position.
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
2. Fold the seatback at on the seat, by either
pulling on the nylon strap, located on the rear
right hand side of the seat, or by lifting the
recline lever, located on the front right
hand side of the seatback.3. Lift either one of the adjuster levers and slide
the seat to the most rearward position. See
“Adjusting the Bucket Seats Forward and
Rearward” earlier in this section.
4. Release the rear set of hooks from the oor
pins by pulling the nylon strap, located at the
base of the seat. Use the strap to guide
the seat forward.
18

5. To release the front seat hooks from the oor
pins, squeeze the angled bar, located beneath
the seat toward the straight crossbar.
6. Remove the seat by rocking it slightly forward,
then toward the rear of the vehicle while
pulling it out. This should be done in
one motion.
Reinstalling the Bucket Seats
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not
provide the protection needed in a crash.
The person wearing the belt could be
seriously injured. After installing the seat,
always check to be sure that the safety
belts are properly routed and attached,
and are not twisted.
Do not install the seat facing the rear of the
vehicle, as it will not lock into place. If more
storage room is needed behind the seat, slide the
seat forward.
Make sure the seat is in the full rear position
before beginning this procedure.
19

To reinstall the bucket seats, do the following:
1. With the seat folded, squeeze the angled bar
beneath the seat toward the straight crossbar,
while placing the front hooks of the seat
into the front two oor pins.
2. Make sure the seat
is angled so that the
front seat hooks
clear the oor pins.
If the front hooks
are not attached
correctly, the seat’s
rear hooks will
not attach to the rear
set of oor pins.
If the front hooks are not attaching correctly,
check that the seat is in the full rear position.3. Firmly push the rear seat hooks into the rear
oor pins by pushing down the rear of
the seat.
20

Removing a Captain Chair (without a
Side Impact Airbag)
If your vehicle has captain chairs with side impact
airbags, the seats cannot be removed. See
Where Are the Airbags? on page 99for more
information.
To remove a captain chair, do the following:
1. Pull the nylon strap behind the seat to release
the rear hooks from the oor pins.2. The seat can then be lifted off the front oor
pins and removed from the vehicle.
24

Installing a Captain Chair (without a
Side Impact Airbag)
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not
provide the protection needed in a crash.
The person wearing the belt could be
seriously injured. After installing the seat,
always check to be sure that the safety
belts are properly routed and attached,
and are not twisted.
Do not put the seats in so they face rearward
because they will not latch that way. For the
second row, if you want more storage room behind
the seat, adjust the seat by sliding it forward.
Make sure the seatbacks are in the upright
position, the seat belts are on the correct side of
the seats and the seats are in the full rear position
before beginning this procedure.To install a captain chair, do the following:
1. Hook the front latches over the front
oor pins.
25

Safety Belts
Safety Belts: They Are for Everyone
This part of the manual tells you how to use
safety belts properly. It also tells you some things
you should not do with safety belts.
{CAUTION:
Do not let anyone ride where he or she
cannot wear a safety belt properly. If you
are in a crash and you are not wearing a
safety belt, your injuries can be much
worse. You can hit things inside the
vehicle or be ejected from it. You can be
seriously injured or killed. In the same
crash, you might not be, if you are
buckled up. Always fasten your safety
belt, and check that your passengers’
belts are fastened properly too.
{CAUTION:
It is extremely dangerous to ride in a
cargo area, inside or outside of a vehicle.
In a collision, people riding in these areas
are more likely to be seriously injured or
killed. Do not allow people to ride in any
area of your vehicle that is not equipped
with seats and safety belts. Be sure
everyone in your vehicle is in a seat and
using a safety belt properly.
Your vehicle has indicators to remind you and
your passengers to buckle your safety belts. See
Safety Belt Reminder Light on page 232and
Passenger Safety Belt Reminder Light on
page 233.
In most states and in all Canadian provinces, the
law says to wear safety belts. Here is why:
They work.
32

Driver Position
Lap-Shoulder Belt
The driver has a lap-shoulder belt. Here is how to
wear it properly.
1. Close and lock the door.
2. Adjust the seat so you can sit up straight. To
see how, see “Seats” in the Index.
3. Pick up the latch plate and pull the belt across
you. Do not let it get twisted.
The lap-shoulder belt may lock if you pull the
belt across you very quickly. If this happens,
let the belt go back slightly to unlock it.
Then pull the belt across you more slowly.
38

Rear Safety Belt Comfort Guides
Rear shoulder belt comfort guides may provide
added safety belt comfort for older children
who have outgrown booster seats and for some
adults. When installed on a shoulder belt, the
comfort guide positions the belt away from
the neck and head.
There is one guide for each second row passenger
position. If your vehicle has a third row, there is
one guide for each outboard position.Here is how to install a comfort guide to the
shoulder belt:
1. Remove the guide from its storage pocket on
the side of the seatback.
52