hood release CHRYSLER 300 SRT 2009 1.G Owners Manual

seat will return to its previously set position when you
insert the key into the ignition switch and turn it out of
the LOCK position.
•When you remove the key from the ignition switch,
the driver seat will move to a position 0.3 in (7.7 mm)
forward of the rear stop if the driver seat position is
between 0.9 in and 2.7 in (22.7 mm and 67.7 mm)
forward of the rear stop. The seat will return to its
previously set position when you insert the key into
the ignition switch and turn it out of the LOCK
position.
•The Easy Entry/Easy Exit feature is disabled when the
driver seat position is less than 0.9 in (22.7 mm)
forward of the rear stop. At this position, there is no
benefit to the driver by moving the seat for Easy Exit
or Easy Entry.
Each stored memory setting will have an associated Easy
Entry and Easy Exit position.NOTE:The Easy Entry/Easy Exit feature can be en-
abled or disabled. Refer to “Automatically Move Seat
Back on Exit,” under “Personal Settings (Customer-
Programmable Features)” under “Electronic Vehicle In-
formation Center (EVIC)” in Section 4.
TO OPEN AND CLOSE THE HOOD
Two latches must be released to open the hood.
1. Pull the hood release lever located under the left side
of the instrument panel.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Move to the outside of the vehicle and push the safety
catch to the left. The safety catch is located under the
center front edge of the hood.Use the hood prop rod (if equipped) to secure the hood in
the open position.
Hood Release LeverHood Safety Catch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133
3

INSTRUMENT PANEL FEATURES
1 - Air Outlet 7 - Radio 13 - Ignition Switch
2 - Instrument Cluster 8 - Climate Control 14 - Hood Release
3 - HAZARD Switch 9 - HEATED SEAT Switch* 15 - TRUNK RELEASE Switch
4 - Analog Clock 10 - Power Outlet 16 - HEADLIGHT Switch
5 - Electronic Stability Program OFF Button* 11 - Ash Tray* * If Equipped
6 - Glove Compartment 12 - Storage Compartment*UNDERSTANDING YOUR INSTRUMENT PANEL 203
4

release it as soon as the starter engages. The starter motor
will disengage automatically in 10 seconds. Once this
occurs, release the accelerator pedal, turn the ignition
switch to the LOCK position, wait 10 to 15 seconds, then
repeat the normal starting procedure.
CAUTION!
To prevent damage to the starter, wait 10 to 15 sec-
onds before trying again.
After Starting
The idle speed is controlled automatically and it will
decrease as the engine warms up.
ENGINE BLOCK HEATER — IF EQUIPPED
The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a
standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.
The engine block heater cord is routed under the hood on
the driver side of the vehicle. It has a removable cap that
is located on the driver side of the Integrated Power
Module.
WARNING!
Remember to disconnect the cord before driving.
Damage to the 110-115 Volt electrical cord could cause
electrocution.
312 STARTING AND OPERATING

filter. Install the new filter with arrows pointing in the
direction of airflow, which is toward the rear of the
vehicle (text and arrows on the filter indicate this).
Refer to the “Maintenance Schedule” in Section 8 for
proper maintenance intervals.
Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
tailgate, sliding doors and hood hinges, should be lubri-
cated periodically with a lithium based grease such as
MOPARSpray White Lube to assure quiet, easy opera-
tion and to protect against rust and wear. Prior to the
application of any lubricant, the parts concerned should
be wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing otherunderhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the Fall and Spring. Apply a small
amount of a high quality lubricant such as MOPAR
Lock Cylinder Lubricant directly into the lock cylinder.Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild nonabrasive cleaner. This will remove accumula-
tions of salt or road film.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield.
MAINTAINING YOUR VEHICLE 407
7

Holder, Coin........................... 194
Holder, Cup........................... 193
HomeLink(Garage Door Opener) Transmitter . . . 181
Hood Release.......................... 132
Ignition............................... 14
Key ...............................12,14
Ignition Key Removal..................... 14
Illuminated Entry........................ 20
Immobilizer (Sentry Key)................... 15
Infant Restraint........................66,67
Information Center, Vehicle................. 214
Instrument Cluster....................204,205
Instrument Panel and Controls.............. 203
Instrument Panel Lens Cleaning............. 423
Integrated Power Module (Fuses)............ 424
Interior Appearance Care.................. 422
Interior Lights.......................... 140
Intermittent Wipers (Delay Wipers)........... 142Introduction............................. 4
Jump Starting.......................... 385
Key, Programming........................ 17
Key, Replacement........................ 16
Key, Sentry (Immobilizer)................... 15
Key-In Reminder......................... 14
Keyless Entry System...................... 20
Keyless Go.......................12,226,308
Keys................................. 12
Kicker Sound System..................... 286
Knee Bolster..........................51,52
Lane Change and Turn Signals.............. 139
Lap/Shoulder Belts....................... 42
LATCH (Lower Anchors and Tether for
CHildren)............................69,70
Latch Plate............................. 44
478 INDEX

Programming Transmitters
(Remote Keyless Entry).................... 20
Radial Ply Tires......................... 350
Radiator Cap (Coolant Pressure Cap).......... 414
Radio Operation........................ 293
Radio Remote Controls.................... 291
Radio, Satellite.......................281,287
Rain Sensitive Wiper System................ 144
Rear Cupholder......................... 193
Rear Park Sense System................... 175
Rear Seat, Folding....................... 127
Rear Window Defroster................... 197
Rear Window Features.................... 197
Reclining Front Seats..................... 123
Recorder, Event Data...................... 64
Recreational Towing...................... 375
Reformulated Gasoline.................... 367
Refrigerant............................ 406Release, Hood.......................... 132
Reminder, Lights On..................... 137
Reminder, Seat Belt....................... 49
Remote Control
Starting System........................ 25
Remote Keyless Entry (RKE)................. 20
Remote Sound System (Radio) Controls........ 291
Remote Starting System.................... 25
Remote Trunk Release..................... 39
Replacement Bulbs....................... 432
Replacement Keys........................ 16
Replacement Parts....................... 399
Replacement Tires....................... 352
Reporting Safety Defects................... 464
Restraint, Head......................... 125
Restraints, Child......................... 66
Restraints, Occupant...................... 41
Rocking Vehicle When Stuck................ 389
Rotation, Tires.......................... 355
INDEX 483
10