stop start CHRYSLER CARAVAN 2000 Service Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2000, Model line: CARAVAN, Model: CHRYSLER CARAVAN 2000Pages: 436, PDF Size: 3.4 MB
Page 2 of 436
TABLE OF CONTENTS - Continued
7.0 DIAGNOSTIC INFORMATION AND PROCEDURES...........................19
7.1GENERAL TROUBLESHOOTING....................................19
TROUBLE CODE TESTS
TEST DTCCHECKING FOR DIAGNOSTIC TROUBLE CODES.............20
TC-1AREPAIRING - A/C CONTROL SHORT CIRCUIT.................22
TC-2AREPAIRING - A/C CONTROL OPEN CIRCUIT..................28
TC-3AREPAIRING - A/C SYSTEM PRESSURE SIGNAL HIGH
EXCEEDED..............................................34
TC-4AREPAIRING - A/C SYSTEM PRESSURE SIGNAL LOW
EXCEEDED..............................................38
TC-5AREPAIRING - A/C SYSTEM PRESSURE SUPPLY HIGH
EXCEEDED..............................................42
TC-6AREPAIRING - A/C SYSTEM PRESSURE SUPPLY LOW
EXCEEDED..............................................46
TC-7AREPAIRING - ACCELERATOR PEDAL SENSOR TROUBLE
CODES.................................................50
TC-14AREPAIRING - BATTERY VOLTAGE SRC HIGH EXCEEDED.......60
TC-15AREPAIRING - TURBOCHARGER BOOST SENSOR SIGNAL HIGH
EXCEEDED..............................................62
TC-16AREPAIRING - TURBOCHARGER BOOST SENSOR SIGNAL LOW
EXCEEDED..............................................70
TC-17AREPAIRING - TURBOCHARGER BOOST SENSOR SUPPLY HIGH
EXCEEDED..............................................74
TC-18AREPAIRING - TURBOCHARGER BOOST SENSOR SUPPLY LOW
EXCEEDED..............................................78
TC-19AREPAIRING - TURBOCHARGER BOOST SENSOR PLAUSIBILITY.82
TC-20AREPAIRING - BRAKE SWITCH PLAUSIBILITY WITH REDUNDANT
CONTACT...............................................86
TC-21AREPAIRING - CLUTCH SIGNAL PLAUSIBILITY.................94
TC-22AREPAIRING - CONTROL SLEEVE SENSOR SIGNAL HIGH
EXCEEDED..............................................98
TC-23AREPAIRING - CONTROL SLEEVE SENSOR START END POSITION
NOT ATTAINED..........................................102
TC-24AREPAIRING - CONTROL SLEEVE SENSOR STOP END POSITION
NOT ATTAINED..........................................104
TC-25AREPAIRING - CRUISE STATUS INDICATOR LAMP SHORT
CIRCUIT................................................106
TC-26AREPAIRING - DIAGNOSTIC LAMP OPEN CIRCUIT............110
TC-27AREPAIRING - DIAGNOSTIC LAMP SHORT CIRCUIT...........114
TC-30AREPAIRING - DIESEL POWER RELAY SHUTS OFF TOO EARLY .118
TC-31AREPAIRING - DIESEL POWER RELAY SHUTS OFF TOO LATE . .122
TC-33AREPAIRING - EGR OPEN CIRCUIT.........................126
TC-34AREPAIRING - EGR SHORT CIRCUIT........................130
TC-35AREPAIRING - ENGINE SPEED SENSOR DYNAMIC
PLAUSIBILITY...........................................134
TC-36AREPAIRING - ENGINE SPEED SENSOR OVERSPEED
RECOGNITION..........................................138
TC-38AREPAIRING - ENGINE SPEED SENSOR STATIC PLAUSIBILITY .140
TC-39AREPAIRING - FAN CONTROL OPEN CIRCUIT FAN 1..........144
TC-40AREPAIRING - FAN CONTROL OPEN CIRCUIT FAN 2..........148
TC-41AREPAIRING - FAN CONTROL SHORT CIRCUIT FAN 1.........152
ii
ProCarManuals.com
Page 3 of 436
TABLE OF CONTENTS - Continued
TC-42AREPAIRING - FAN CONTROL SHORT CIRCUIT FAN 2.........156
TC-43AREPAIRING - FUEL QUANTITY ACTUATOR NEG. GOVERNOR
DEVIATION COLD.......................................160
TC-44AREPAIRING - FUEL QUANTITY ACTUATOR NEG. GOVERNOR
DEVIATION WARM.......................................164
TC-45AREPAIRING - FUEL QUANTITY ACTUATOR POS. GOVERNOR
DEVIATION COLD.......................................168
TC-46AREPAIRING - FUEL QUANTITY ACTUATOR POS. GOVERNOR
DEVIATION WARM.......................................172
TC-47AREPAIRING - FUEL TEMPERATURE SENSOR SRC HIGH
EXCEEDED.............................................176
TC-48AREPAIRING - FUEL TEMPERATURE SENSOR SRC LOW
EXCEEDED.............................................180
TC-51AREPAIRING - GLOW RELAY #1 CONTROLLER OPEN CIRCUIT .184
TC-52AREPAIRING - GLOW RELAY #2 CONTROLLER OPEN CIRCUIT .188
TC-53AREPAIRING - GLOW RELAY #1 CONTROLLER SHORT
CIRCUIT................................................192
TC-54AREPAIRING - GLOW RELAY #2 CONTROLLER SHORT
CIRCUIT................................................196
TC-56AREPAIRING - INDUCTIVE AUXILIARY SPEED SENSOR DYNAMIC
PLAUSIBILITY...........................................200
TC-57AREPAIRING - INDUCTIVE AUXILIARY SPEED SENSOR
OVERSPEED RECOGNITION..............................204
TC-58AREPAIRING - INDUCTIVE AUXILIARY SPEED SENSOR
PLAUSIBILITY...........................................208
TC-59AREPAIRING - INDUCTIVE AUXILIARY SPEED SENSOR STATIC
PLAUSIBILITY...........................................212
TC-62AREPAIRING - INTAKE AIR TEMPERATURE SENSOR SIGNAL HIGH
EXCEEDED.............................................216
TC-63AREPAIRING - INTAKE AIR TEMPERATURE SENSOR SIGNAL LOW
EXCEEDED.............................................220
TC-72AREPAIRING - NEEDLE MOVEMENT SENSOR SRC HIGH
EXCEEDED.............................................224
TC-73AREPAIRING - NEEDLE MOVEMENT SENSOR SRC LOW
EXCEEDED.............................................228
TC-74AREPAIRING - REDUNDANT EMERGENCY STOP PLAUSIBILITY IN
AFTER-RUN............................................232
TC-75AREPAIRING - REDUNDANT EMERGENCY STOP POWERSTAGE
DEFECTIVE.............................................236
TC-76AREPAIRING - SMART START RELAY SHORT CIRCUIT.........240
TC-79AREPAIRING - SOLENOID VALVE CONTROLLER OPEN
CIRCUIT................................................242
TC-80AREPAIRING - SOLENOID VALVE CONTROLLER SHORT
CIRCUIT................................................246
TC-81AREPAIRING - TEMPERATURE OF ENGINE COOLANT SRC HIGH
EXCEEDED.............................................250
TC-82AREPAIRING - TEMPERATURE OF ENGINE COOLANT SRC LOW
EXCEEDED.............................................254
TC-84AREPAIRING - TERMINAL 15 PLAUSIBILITY AFTER START-UP . . .258
TC-85AREPAIRING - TIMING GOVERNING NEGATIVE GOVERNOR
DEVIATION.............................................262
iii
ProCarManuals.com
Page 10 of 436
The secret key and challenge are plugged into an algorithm that produces the encrypted response
message. The transponder uses the crypto algorithm to receive, decode and respond to the
message sent by SKIM. After responding to the coded message, the transponder sends a
transponder I.D. message to the SKIM. The SKIM compares the transponder I.D. to the available
valid key codes in SKIM memory (8 key maximum). After validating the key the SKIM sends a
CCD Bus message called a ªSeed Requestº to the body controller then waits for a body controller
response. If the body controller does not respond, the SKIM will send the seed request again.
After three failed attempts the SKIM will stop sending the seed request and store a trouble code.
If the body controller sends a seed response, the SKIM sends a valid/invalid key message to the
body controller. This is an encrypted message that is generated using the following:
VIN þ Vehicle Identification Number
Seed þ This is a random number that is generated by the BCM at each ignition key cycle.
The VIN and seed are plugged into a rolling code algorithm that encrypts the ªvalid/invalid keyº
message. The body controller uses the rolling code algorithm to receive, decode and respond to
the valid/invalid key message sent by SKIM. After sending the valid/invalid key message the SKIM
waits 3.5 seconds for a PCM status message from the body controller. If the BCM does not
respond with a valid key message to the SKIM, a fault is detected and a trouble code stored.
The SKIS incorporates a warning (``ALARM SET'') lamp located in the message center. The lamp
receives switched ignition voltage and is hardwired to the body controller. The lamp is actuated
when the SKIM sends a CCD Bus message to the body controller requesting the lamp on. The
body controller then provides the ground for the lamp. The SKIM will request lamp operation for
the following:
± ± bulb check at ignition on
± to alert the vehicle operator to a SKIS malfunction
For all faults except transponder faults and VIN mismatch, the lamp remains on steady. In the
event of a transponder fault the light flashes at the rate of 1Hz (once per second). If a fault is
present the lamp will remain on or flashing for the complete ignition cycle. If a fault is stored in
SKIM memory which prevents the system from operating properly, the ECM will allow the engine
to start and run (for 2 seconds) up to six times. After the sixth attempt, the ECM disables the
starter relay until the fault is corrected..
3.3 Diagnostic Trouble Codes
Each diagnostic trouble code is diagnosed by following a specific testing procedure. The
diagnostic test procedures contain step-by-step instructions for determining the cause of trouble
codes as well as no trouble code problems. It is not necessary to perform all of the tests in this
book to diagnose an individual code.
Always begin by reading the diagnostic trouble codes using the DRB. This procedure begins in
the DTC TEST - Checking the System for Diagnostic Trouble Codes. This will direct you to the
specific test(s) that must be performed.
3.3.1 Hard Code
A diagnostic trouble code that comes back within one cycle of the ignition key is a ªhardº code.
This means that the defect is there every time the engine control module/SKIM checks that circuit
or function. Procedures in this manual verify if the trouble code is a hard code at the beginning
of each test. When it is not a hard code, an ªintermittentº test must be performed.
G
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
4
ProCarManuals.com
Page 11 of 436
3.3.2 Intermittent Code
A diagnostic trouble code that is not there every time the engine control module/SKIM checks the
circuit is an ªintermittentº code. Most intermittent codes are caused by wiring or connector
problems. Defects that come and go like this are the most difficult to diagnose; they must be
looked for under specific conditions that cause them. The following checks may assist you in
identifying a possible intermittent problem:
²Visually inspect related wire harness connectors. Look for broken, bent, pushed out, or
corroded terminals.
²Visually inspect the related harnesses. Look for chafed, pierced, or partially broken wire.
²Refer to any hotlines or technical service bulletins that may apply.
NOTE: Electromagnetic (radio) interference can cause an intermittent system malfunction. This
interference can interrupt communication between the ignition key transponder and the SKIM.
3.3.3 Reset Counter
The reset counter counts the number of times the vehicle has been started since codes were last
set, erased, or the battery was disconnected. The reset counter will count up to 255 start counts.
The number of starts helps determine when the trouble code actually happened. This is recorded
by the ECM and can be viewed on the DRB as the RESET COUNTER.
When there are no trouble codes stored in memory, the DRB will display ªNO TROUBLE CODES
FOUNDº and the reset counter will show ªRESET COUNT = XXX.º
3.3.4 ECM Diagnostic Trouble Codes
A/C CONTROL SHORT CIRCUIT
A/C CONTROL OPEN CIRCUIT
A/C SYSTEM PRESSURE SIGNAL HIGH EXCEEDED
A/C SYSTEM PRESSURE SIGNAL LOW EXCEEDED
A/C SYSTEM PRESSURE SUPPLY HIGH EXCEEDED
A/C SYSTEM PRESSURE SUPPLY LOW EXCEEDED
ACCELERATOR PEDAL SENSOR SIGNAL HIGH EXCEEDED
ACCELERATOR PEDAL SENSOR PLAUSIBILITY
ACCELERATOR PEDAL SENSOR PWG PLAUS WITH LOW IDLE SWITCH
ACCELERATOR PEDAL SENSOR PWG PLAUS WITH POTENTIOMETER
ATMOSPHERIC PRESSURE SENSOR SRC HIGH EXCEEDED
ATMOSPHERIC PRESSURE SENSOR SRC LOW EXCEEDED
BATTERY VOLTAGE SRC HIGH EXCEEDED
BRAKE SIGNAL PLAUS WITH REDUNDANT CONTACT
CLUTCH SIGNAL PLAUSIBILITY
CONTROL SLEEVE SENSOR SIGNAL HIGH EXCEEDED
CONTROL SLEEVE SENSOR START END POS. NOT ATTAINED
CONTROL SLEEVE SENSOR STOP END POS. NOT ATTAINED
CRUISE STATUS INDICATOR LAMP SHORT CIRCUIT
DIAGNOSTIC LAMP OPEN CIRCUIT
DIAGNOSTIC LAMP SHORT CIRCUIT
DIESEL POWER RELAY SHUTS OFF TOO EARLY
DIESEL POWER RELAY SHUTS OFF TOO LATE
EEPROM PLAUSIBILITY CHECKSUM ERROR FOR ADJ. (EGR)
EEPROM PLAUSIBILITY CHECKSUM ERROR IN CC212
EEPROM PLAUSIBILITY COMMUNICATION WITH EEPROM
EEPROM PLAUSIBILITY FUNC. SWITCH WRONG OR MISSING
EEPROM PLAUSIBILITY VER. NUMBER NOT CORRESPONDING
G
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
5
ProCarManuals.com
Page 12 of 436
EGR OPEN CIRCUIT
EGR SHORT CIRCUIT
ENGINE SPEED SENSOR DYNAMIC PLAUSIBILITY
ENGINE SPEED SENSOR OVER SPEED RECOGNITION
ENGINE SPEED SENSOR STATIC PLAUSIBILITY
FAN CONTROL OPEN CIRCUIT FAN#1
FAN CONTROL OPEN CIRCUIT FAN #2
FAN CONTROL SHORT CIRCUIT FAN #1
FAN CONTROL SHORT CIRCUIT FAN #2
FUEL QUANTITY ACTUATOR NEG. GOV. DEVIATION COLD
FUEL QUANTITY ACTUATOR NEG. GOV. DEVIATION WARM
FUEL QUANTITY ACTUATOR POS. GOV. DEVIATION COLD
FUEL QUANTITY ACTUATOR POS. GOV. DEVIATION WARM
FUEL TEMPERATURE SENSOR SRC HIGH EXCEEDED
FUEL TEMPERATURE SENSOR SRC LOW EXCEEDED
GLOW RELAY #1 CONTROLLER OPEN CIRCUIT
GLOW RELAY #2 CONTROLLER OPEN CIRCUIT
GLOW RELAY #1 CONTROLLER SHORT CIRCUIT
GLOW RELAY #2 CONTROLLER SHORT CIRCUIT
IMMOBILIZER SIGNAL LOST
INVALID SKIM MESSAGE
INDUCTIVE AUX. SPEED SENSOR DYNAMIC PLAUSIBILITY
INDUCTIVE AUX. SPEED SENSOR OVERSPEED RECOGNITION
INDUCTIVE AUX. SPEED SENSOR PLAUSIBILITY
INDUCTIVE AUX. SPEED SENSOR STATIC PLAUSIBILITY
MICROCONTROLLER GATE-ARRAY MONITORING
MICROCONTROLLER GATE-ARRAY WATCHDOG
MICROCONTROLLER PREPARE FUEL QUANTITY STOP
MICROCONTROLLER RECOVERY HAS OCCURRED
MICROCONTROLLER REDUNDANT OVERRUN MONITORING
NEEDLE MOVEMENT SENSOR SRC HIGH EXCEEDED
NEEDLE MOVEMENT SENSOR SRC LOW EXCEEDED
REDUNDANT EMER. STOP PLAUSIBILITY IN AFTER-RUN
REDUNDANT EMER. STOP POWERSTAGE DEFECTIVE
REGULATOR LOWER REGULATOR LIMIT
REGULATOR UPPER LIMIT
SOLENOID VALVE CONTROLLER OPEN CIRCUIT
SOLENOID VALVE CONTROLLER SHORT CIRCUIT
TEMPERATURE OF ENGINE COOLANT SRC HIGH EXCEEDED
TEMPERATURE OF ENGINE COOLANT SRC LOW EXCEEDED
TERMINAL #15 PLAUSIBILITY AFTER START-UP
TIMING GOVERNING NEGATIVE GOVERNOR DEVIATION
TIMING GOVERNING POSITIVE GOVERNOR DEVIATION
TURBOCHARGER BOOST SENSOR SIGNAL HIGH EXCEEDED
TURBOCHARGER BOOST SENSOR SIGNAL LOW EXCEEDED
TURBOCHARGER BOOST SENSOR SUPPLY HIGH EXCEEDED
TURBOCHARGER BOOST SENSOR SUPPLY LOW EXCEEDED
TURBOCHARGER BOOST SENSOR PLAUSIBILITY
VEHICLE SPEED SENSOR PEC FREQUENCY TOO HIGH
VEHICLE SPEED SENSOR SIGNAL SRC HIGH EXCEEDED
VEHICLE SPEED SENSOR PLAUSIBILITYG
E
N
E
R
A
L
I
N
F
O
R
M
A
T
I
O
N
6
ProCarManuals.com
Page 26 of 436
TEST DTCCHECKING FOR DIAGNOSTIC TROUBLE CODES
NOTE: The battery must be fully charged for any test in this manual.
1. Attempt to start the engine. Crank for up to 10 seconds if necessary.
2. Connect the DRB to the data link connector. Write down the trouble codes that are displayed.
3. If the DRB displays ``No Response'', go toTEST NS-2A.
4. If the DRB screen is blank or has a DRB error message, go toGeneral Information Section
3.5in this manual.
5. Iftrouble code messagesare displayed, refer to the trouble code list below and on the
following page for the appropriate test.
6. If there are no ECM trouble codes displayed, refer to one of the following:
For Immobilizer problems..................................................SK-1A
For Driveability problems.................................................NTC-1A
For No Start problems....................................................NS-1A
For Speed Control problems...............................................SC-1A
NOTE:For all component locations see General Information Section 4.0 in this manual.
DRB DIAGNOSTIC TROUBLE CODE (DTC) DISPLAYEDDIAGNOSTIC
TESTSCAN
TOOL
AC Control Short CircuitTC-1 P1655
A/C Control Open CircuitTC-2 P1655
A/C System Pressure Signal High Exceeded TC-3 P1695
A/C System Pressure Signal Low Exceeded TC-4 P1695
A/C System Pressure Supply High Exceeded TC-5 P1695
A/C System Pressure Supply Low Exceeded TC-6 P1695
Accelerator Pedal Sensor High Exceeded TC-7 P1515
Accelerator Pedal Sensor PlausibilityTC-7 P1515
Accelerator Pedal Sensor Pwg Plaus With Low Idle Switch TC-7 P1515
Accelerator Pedal Sensor Pwg Plaus With Potentiometer TC-7 P1515
Atmospheric Pressure Sensor SRC High Exceeded ** P1105
Atmospheric Pressure Sensor SRC Low Exceeded ** P1105
Battery Voltage SRC High Exceeded TC-14 P1600
Turbocharger Boost Sensor Signal High Exceeded TC-15 P0235
Turbocharger Boost Sensor Signal Low Exceeded TC-16 P0235
Turbocharger Boost Sensor Supply High Exceeded TC-17 P0235
Turbocharger Boost Sensor Supply Low Exceeded TC-18 P0235
Turbocharger Boost Sensor Plausibility TC-19 P0235
Brake Signal Plaus With Redundant Contact TC-20 P1703
Clutch Signal PlausibilityTC-21 P1740
Control Sleeve Sensor Signal High Exceeded TC-22 P1225
Control Sleeve Sensor Start End Pos. Not Attained TC-23 P1225
Control Sleeve Sensor Stop End Pos. Not Attained TC-24 P1225
Cruise Status Indicator Lamp Short Circuit TC-25 P1665
Diagnostic Lamp Open CircuitTC-26 P1650
Diagnostic Lamp Short CircuitTC-27 P1650
Diesel Power Relay Shuts Off Too Early TC-30 P1625
Diesel Power Relay Shuts Off Too Late TC-31 P1625
EEPROM Plausibility Checksum Error For Adj. ** P1680
EEPROM Plausibility Checksum Error in CC212 ** P1680
EEPROM Plausibility Communication with EEPROM ** P1680
EEPROM Plausibility Func. Switch Wrong or Missing ** P1680
EEPROM Plausibility Ver. Number Not Corresponding ** P1680
EGR Open CircuitTC-33 P0400
EGR Short CircuitTC-34 P0400
Engine Speed Sensor Dynamic Plausibility TC-35 P0725
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
20
ProCarManuals.com
Page 27 of 436
TEST DTCCHECKING FOR DIAGNOSTIC TROUBLE CODES
DRBIIITDIAGNOSTIC TROUBLE CODE (DTC) DISPLAYEDDIAGNOSTIC
TESTSCAN
TOOL
Engine Speed Sensor Over Speed Recognition TC-36 P0725
Engine Speed Sensor Static Plausibility TC-38 P0725
Fan Control Open Circuit Fan #1TC-39 P1690
Fan Control Open Circuit Fan #2TC-40 P1690
Fan Control Short Circuit Fan #1TC-41 P1690
Fan Control Short Circuit Fan #2TC-42 P1690
Fuel Quantity Actuator Neg. Gov. Deviation Cold TC-43 P1220
Fuel Quantity Actuator Neg. Gov. Deviation Warm TC-44 P1220
Fuel Quantity Actuator Pos. Gov. Deviation Cold TC-45 P1220
Fuel Quantity Actuator Pos. Gov. Deviation Warm TC-46 P1220
Fuel Temperature Sensor SRC High Exceeded TC-47 P0180
Fuel Temperature Sensor SRC Low Exceeded TC-48 P0180
Glow Relay #1 Controller Open Circuit TC-51 P1635
Glow Relay #2 Controller Open Circuit TC-52 P1635
Glow Relay #1 Controller Short Circuit TC-53 P1635
Glow Relay #2 Controller Short Circuit TC-54 P1635
Inductive Aux. Speed Sensor Dynamic Plausibility TC-56 P1725
Inductive Aux. Speed Sensor Overspeed Recognition TC-57 P1725
Inductive Aux. Speed Sensor Plausibility TC-58 P1725
Inductive Aux. Speed Sensor Static Plausibility TC-59 P1725
Intake Air Temperature Sensor Signal High Exceeded TC-62 P0110
Intake Air Temperature Sensor Signal Low Exceeded TC-63 P0110
Microcontroller Gate-array Monitoring** P1615
Microcontroller Gate-array Watchdog** P1615
Microcontroller Prepare Fuel Quantity Stop ** P1615
Microcontroller Recovery Has Occurred ** P1615
Microcontroller Redundant Overrun Monitoring ** P1615
Needle Movement Sensor High Exceeded TC-72 P1201
Needle Movement Sensor Low Exceeded TC-73 P1201
Redundant Emer. Stop Plausibility in After-run TC-74 P1660
Redundant Emer. Stop Powerstate Defective TC-75 P1660
Regulator Lower Regulator Limit** P1610
Regulator Upper Regulator Limit** P1610
Smart Start Relay Short CircuitTC-76 P1675
Solenoid Valve Controller Open Circuit TC-79 P1630
Solenoid Valve Controller Short Circuit TC-80 P1630
Temperature of Engine Coolant SRC High Exceeded TC-81 P0115
Temperature of Engine Coolant SRC Low Exceeded TC-82 P0115
Terminal #15 Plausibility After Start-up TC-84 P1605
Timing Governing Negative Governor Deviation TC-85 P1230
Timing Governing Positive Governor Deviation TC-86 P1230
UþREF (2.5V)** P1620
Vehicle Speed Sensor Pec Frequency Too High TC-91 P0500
Vehicle Speed Sensor Signal High Exceeded TC-91 P0500
Vehicle Speed Sensor PlausibilityTC-91 P0500
Immobilizer Signal LostTC-94 P1685
Invalid SKIM MessageTC-94 P1685
** These trouble codes indicate an internal ECM fault. Using the DRB, clear ECM trouble code(s).
Perform several engine run cycles turning the ignition off for at least 10 seconds between cycles.
Using the DRB, read ECM trouble codes. If the code is present, replace the Engine Control Module.
NOTE: If trouble code TERMINAL 15 PLAUSIBILITY AFTER START-UP is present with other trouble
codes, perform TC-84 diagnosis first.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
21
ProCarManuals.com
Page 111 of 436
TEST TC-24AREPAIRING - CONTROL SLEEVE SENSOR STOP END POSITION NOT ATTAINED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
NOTE: IF OTHER TURN IGNITION ON.
START TEST DTC'S ARE PRESENT,
TC-24A. DIAGNOSE OTHER USING THE DRB,
DTC'S BEFORE ERASE CODES.
CONTINUING.
PERFORM SEVERAL
DRIVE CYCLES TURNING BETWEEN EACH DRIVE
THE IGNITION OFF FOR CYCLE.
AT LEAST 10
SECONDS...
DOES THE DRB
USING THE DRB, DISPLAY "CONTROL NO
READ TROUBLE SLEEVE SENSOR STOP TEST COMPLETE.*
CODES. END POSITION NOT
ATTAINED"?
YES
PERFORM SEVERAL
REPLACE THE FUEL DRIVE CYCLES TURNING BETWEEN EACH DRIVE
INJECTION PUMP THE IGNITION OFF FOR CYCLE.
ASSEMBLY. AT LEAST 10
SECONDS...
DOES THE DRB
USING THE DRB, DISPLAY "CONTROL NO
READ TROUBLE SLEEVE SENSOR STOP TEST COMPLETE.*
CODES. END POSITION NOT
ATTAINED"?
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
105
ProCarManuals.com
Page 243 of 436
TEST TC-75AREPAIRING - REDUNDANT EMERGENCY STOP POWERSTAGE DEFECTIVE
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST WITH THE DRB,
TC-75A. ERASE CODES.
CYCLE THE IGNITION DOES THE DRB
ON AND OFF SEVERAL WITH THE IGNITION DISPLAY "REDUNDANT YES CONTINUE TEST
TIMES, PAUSING FOR ON ENGINE OFF, EMERG STOP TC-75A ON THE
TEN SECONDS AT KEY READ CODES. POWERSTAGE NEXT PAGE.
ON AND OFF. DEFECTIVE"?
NO
AT THIS TIME THE REVIEW THE CIRCUIT
CONDITION FOR DESCRIPTION FOR A WERE ANY PROBLEMS YES REPAIR AS
SETTING THE CODE PROPER UNDERSTANDING FOUND? NECESSARY.*
IS NOT PRESENT. OF THIS CODE. CHECK
FIG.1 FOR PROBLEMS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
237
ProCarManuals.com
Page 371 of 436
TEST NTC-11DCHECKING RADIATOR FAN OPERATION
Perform TEST NTC-11A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST STOP LOW SPEED FAN
NTC-11D. ACTUATION.
KEY OFF.
SUBSTITUTE THE RAD PERFORM THE DO BOTH FANS CYCLE YES REPLACE THE
FAN #1 RELAY WITH "LOW SPEED FAN" ON AND OFF? INITIAL RAD FAN #1
A KNOWN GOOD ACTUATOR TEST. RELAY.*
RELAY.
NO
DISCONNECT THE
DISCONNECT RAD FAN LEFT SIDE FAN
#1 RELAY HARNESS MOTOR HARNESS
CONNECTOR.** CONNECTOR.**
USING AN OHMMETER, REPAIR THE SHORT
MEASURE THE GROUND IS THE RESISTANCE YES TO GROUND BETWEEN
CKT AT CAVITY 8 TO BELOW 10.0 OHMS? THE LEFT SIDE
GROUND. MOTOR AND RAD FAN
FIG.1 #1 REKAY.
NO
DISCONNECT THE USING AN OHMMETER, REPAIR THE RIGHT
RIGHT SIDE FAN MEASURE CAVITY 5 IS THE RESISTANCE YES SIDE FAN SUPPLY
MOTOR HARNESS TO GROUND. BELOW 10.0 OHMS? CIRCUIT FOR A
CONNECTOR.** SHORT TO GROUND.*
FIG.1
NO
CHECK RIGHT SIDE IS ANYTHING
FAN MOTOR FOR PREVENTING THE FAN YES REPAIR AS
BINDING OR DEBRIS MOTOR FROM NECESSARY.
WHICH MAY PREVENT TURNING?
FAN OPERATION.
NO
REPLACE THE RIGHT
SIDE FAN MOTOR.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
365
ProCarManuals.com