ignition CHRYSLER CARAVAN 2000 Service Manual

TEST NTC-10ACONTINUED - CHECKING THE FUEL HEATER AND THE CRANKCASE VENT HEATER
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST NTC-10A CONNECT A TEST
CONTINUED FROM WITH THE IGNITION LIGHT BETWEEN
THE PREVIOUS STILL ON... GROUND AND THE
PAGE. FUEL HEATER RELAY
OUTPUT CKT. AT...
THE CRANKCASE VENT REPAIR THE OPEN FUEL
HEATER HARNESS IS THE TEST LIGHT NO HEATER RELAY OUTPUT
CONNECTOR. ON? CKT FROM THE SPLICE
TO THE CRANKCASE
FIG. 1 VENT HEATER.*
YES
CONNECT A TEST LIGHT REPAIR THE OPEN
ACROSS THE CRANKCASE IS THE TEST LIGHT NO CRANKCASE VENT
VENT HEATER HARNESS ON? HEATER GROUND
CONNECTOR. CIRCUIT.*
FIG. 1
YES
USING AN OHMMETER,
MEASURE RESISTANCE IS THE RESISTANCE NO REPLACE THE
OF THE CRANKCASE BETWEEN CRANKCASE VENT
VENT HEATER. 10.0 AND 16.0 OHMS? HEATER.*
FIG.1
YES
TEST COMPLETE.
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
349
ProCarManuals.com

TEST NTC-10BCHECKING THE FUEL HEATER AND THE CRANKCASE VENT HEATER
Perform TEST NTC-10A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST
NTC-10B. TURN IGNITION OFF.
REPLACE FUSE #16.
NO
TURN IGNITION ON IS THE FUSE OPEN? TEST COMPLETE.*
AND INSPECT FUSE
#16.
YES
CONNECT A JUMPER
REMOVE FUEL HEATER WIRE ACROSS FUEL
RELAY. HEATER RELAY
CAVITIES 30 & 87
(IN PDC). FIG. 1
REPLACE FUSE #6 NO REPLACE THE FUEL
IS THE FUSE OPEN? HEATER RELAY.*
TURN IGNITION ON.
YES
KEY OFF. REPLACE FUSE #16 AND
TURN IGNITION ON. NO REPLACE THE FUEL
DISCONNECT THE IS THE FUSE OPEN? HEATER.*
FUEL HEATER INSPECT FUSE #16.
HARNESS CONNECTOR.
YES
KEY OFF. REPLACE FUSE #16 AND
DISCONNECT THE TURN IGNITION ON. NO REPLACE THE
CRANKCASE VENT IS THE FUSE OPEN? CRANKCASE VENT
HEATER HARNESS INSPECT FUSE #16. HEATER.*
CONNECTOR.
YES
REPAIR THE FUEL
HEATER RELAY
OUTPUT CIRCUIT FOR
A SHORT TO
GROUND.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
351
ProCarManuals.com

TEST NTC-11ACHECKING RADIATOR FAN OPERATION
Perform TEST NTC-1A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST INSTALL DRB. TURN
NTC-11A. IGNITION ON.
OBSERVE THE LEFT
PERFORM THE SIDE AND RIGHT DO BOTH FANS CYCLE YES PERFORM TEST
"LOW SPEED RAD FAN" SIDE RAD FAN ON AND OFF? NTC-11B.
ACTUATOR TEST. OPERATION.
NO
DID EITHER FAN NO PERFORM TEST
CYCLE? NTC-11C.
YES
DID LEFT SIDE FAN NO CONTINUE TEST
CYCLE? NTC-11A ON THE
NEXT PAGE.
YES
PERFORM TEST
NTC-11D.
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
353
ProCarManuals.com

TEST NTC-11ACONTINUED - CHECKING RADIATOR FAN OPERATION
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST NTC-11A
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
KEY ON. REPAIR SHORT TO
REMOVE RAD FAN DOES THE LEFT SIDE YES GROUND IN RAD FAN
RELAY #1.** USING THE DRB, RAD FAN CYCLE ON GROUND CKT. BETWEEN
ACTUATE LOW SPEED AND OFF? LEFT SIDE RAD FAN
RAD FAN. AND RELAY #1*
NO
KEY OFF. USE AN BETWEEN RAD FAN
OHMMETER IN THE RELAY #1 TERMINALS IS THE RESISTANCE YES REPLACE THE RAD
FOLLOWING STEPS. 30 AND 87. BELOW 5.0 OHMS? FAN RELAY #1.*
MEASURE THE
RESISTANCE... FIG.1
NO
DISCONNECT THE MEASURE RESISTANCE REPAIR THE SHORT
RIGHT SIDE RAD FAN BETWEEN RAD FAN IS THE RESISTANCE YES TO GROUND IN THE
HARNESS RELAY #1 HARNESS BELOW 5.0 OHMS? RAD FAN RELAY #3
CONNECTOR.** CONNECTOR CAVITY 5 OUTPUT CIRCUIT.*
AND GROUND. FIG.2
NO
REPLACE THE RIGHT
SIDE RADIATOR
FAN.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
355
ProCarManuals.com

TEST NTC-11BCONTINUED - CHECKING RADIATOR FAN OPERATION
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST NTC-11B
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
TURN IGNITION ON. REPAIR THE OPEN
DISCONNECT RAD FAN USING A VOLTMETER, IS THE VOLTAGE NO FUSED BATTERY SUPPLY
RELAY #3.** MEASURE RELAY ABOVE 10.0 VOLTS? CKT. IF THE FUSE IS
HARNESS CONNECTOR BLOWN, CHECK FOR
CAVITY 8. FIG.1 SHORT TO GROUND.*
YES
CONNECT A JUMPER CAVITIES 2 AND 8.
WIRE ACROSS RAD IS THE RIGHT SIDE NO REPAIR OPEN RAD
FAN RELAY #3 RAD FAN ON? FAN RELAY #3
HARNESSOUTPUT CIRCUIT.*
CONNECTOR... FIG.1
YES
DISCONNECT RAD FAN RAD FAN RLY #1
RELAY #1 AND #3 HARNESS CONN. CAVITY IS THE RESISTANCE NO REPAIR OPEN HIGH
HARNESS CONNECTORS. 6 AND RAD FAN RLY #3 BELOW 5.0 OHMS? SPEED FAN CONTROL
MEASURE RESISTANCE HARNESS CONN. CAVITY CIRCUIT.*
BETWEEN... 6. FIG.1 AND 2
YES
MEASURE RESISTANCE RAD FAN RELAY #3
BETWEEN RAD FAN HARNESS CONNECTOR IS THE RESISTANCE NO REPAIR THE OPEN
RELAY #1 HARNESS CAVITY 4. BELOW 5.0 OHMS? DIESEL POWER RELAY
CONNECTOR CAVITY 4OUTPUT CIRCUIT.*
AND... FIG.1
YES
REPLACE THE RAD
FAN RELAY #3.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
359
ProCarManuals.com

TEST NTC-11CCHECKING RADIATOR FAN OPERATION
Perform TEST NTC-11A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST
NTC-11C. TURN IGNITION OFF.
USING A VOLTMETER,
DISCONNECT THE RAD MEASURE RAD FAN IS THE VOLTAGE NO REPAIR OPEN
FAN RELAY #2.** RELAY #2 HARNESS ABOVE 11.0 VOLTS? BATTERY SUPPLY
CONNECTOR CAVITY 8. CIRCUIT OR FUSE.*
FIG.1
YES
CONNECT A JUMPER
WIRE ACROSS RAD CAVITIES 8 AND 2. DID THE FANS TURN YES REPLACE RAD FAN
FAN RELAY #2 ON? RELAY #2.*
HARNESS
CONNECTOR... FIG.1
NO
REPAIR RELAY #2
DID THE BATTERY YES OUTPUT CKT. FOR
SUPPLY FUSE BLOW? SHORT TO GROUND OR
SHORTED LEFT SIDE
RAD FAN MOTOR.*
NO
DISCONNECT FAN USE A VOLTMETER TO
MOTOR HARNESS MEASURE FAN MOTOR IS THE VOLTAGE NO REPAIR OPEN RELAY
CONNECTOR.** HARNESS CONNECTOR ABOVE 10.0 VOLTS? #2 OUTPUT
WITH JUMPER STILL CAVITY 4. CIRCUIT.*
CONNECTED... FIG.2
YES
RECONNECT FAN CONNECT A JUMPER REPAIR OPEN CKT
MOTOR HARNESS WIRE BETWEEN GROUND DID LEFT SIDE RAD NO BETWEEN RLY #1 AND
CONNECTOR. AND RAD FAN RELAY #1 FAN TURN ON? LEFT SIDE FAN MTR.*
DISCONNECT RAD FAN HARNESS CONNECTOR IF OK, REPLACE LEFT
RELAY #1.** CAVITY 8. FIG.3 SIDE FAN MTR.
YES
CONTINUE TEST
NTC-11C ON THE
NEXT PAGE.
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
361
ProCarManuals.com

TEST SC-1ACONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-1A
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
USING THE SCHEMATIC
AS A GUIDE, INSPECT WERE ANY PROBLEMS YES REPAIR AS
THE WIRING AND FOUND? NECESSARY.*
CONNECTORS.
FIG.1
NO
CHECK THE BRAKE LAMP ARE THE BRAKE LAMP
SWITCH AND CLUTCH SWITCH AND CLUTCH NO ADJUST OR REPLACE
PEDAL SWITCH PEDAL SWITCH AS NECESSARY.*
ADJUSTMENTS. ADJUSTED CORRECTLY?
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
375
ProCarManuals.com

TEST SC-3ACONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-3A KEY OFF.
CONTINUED FROM
THE PREVIOUS DISCONNECT THE BRAKE
PAGE. LAMP SWITCH HARNESS
CONNECTOR.**
USING A VOLTMETER, REPAIR THE BRAKE
PROBE BRAKE LAMP IS THE VOLTAGE NO LAMP SWITCH FUSED
SWITCH HARNESS ABOVE 9.0 VOLTS? BATTERY SUPPLY
CONNECTOR CAVITY 6. CIRCUIT FOR AN
FIG.1 OPEN.*
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN BRAKE LAMP DISPLAY CHANGE YES ADJUST OR REPLACE
SWITCH HARNESS TURN IGNITION ON. FROM "RELEASED" TO THE BRAKE LAMP
CONNECTOR CAVITIES "PRESSED"? SWITCH.*
5 AND 6. FIG.1
NO
REMOVE THE JUMPER. AT THE BRAKE LAMP REPAIR THE PRIMARY
USING A VOLTMETER, SWITCH HARNESS IS THE VOLTAGE NO BRAKE SWITCH
MEASURE THE CONNECTOR CAVITY 5. BELOW 1.0 VOLT? SIGNAL CIRCUIT FOR
PRIMARY SWITCH A SHORT TO
SIGNAL CIRCUIT... FIG.1 VOLTAGE.*
YES
KEY OFF. USING AN OHMMETER, REPAIR THE PRIMARY
MEASURE RESISTANCE IS THE RESISTANCE NO BRAKE SWITCH
DISCONNECT THE ECM OF THE PRIMARY BRAKE BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
HARNESS SW SIGNAL CKT. AN OPEN.*
CONNECTORS.** FIG.2
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
381
ProCarManuals.com

TEST SC-3BCHECKING SPEED CONTROL OPERATION
Perform TEST SC-3A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
START TEST
SC-3B. TURN IGNITION OFF.
DISCONNECT THE KEY ON. USING A
BRAKE LAMP SWITCH VOLTMETER, MEASURE IS THE VOLTAGE NO CONTINUE TEST
HARNESS VOLTAGE AT CAVITY 1. ABOVE 9.0 VOLTS? SC-3B ON THE
CONNECTOR.** NEXT PAGE.
FIG.1
YES
USING A JUMPER WHILE MONITORING DID THE DRB
WIRE, CONNECT THE DRB. DISPLAY CHANGE YES ADJUST OR REPLACE
BRAKE LAMP SWITCH FROM "PRESSED" TO THE BRAKE LAMP
CONNECTOR CAVITY 1 "RELEASED"? SWITCH.*
TO GROUND... FIG.1
NO
USING AN OHMMETER,REPAIR THE OPEN
MEASURE THE IS THE RESISTANCE YES SECONDARY BRAKE
RESISTANCE BETWEEN ABOVE 10.0 OHMS? LAMP SWITCH GROUND
CONNECTOR CAVITY 2CIRCUIT.*
AND GROUND. FIG.1
NO
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
383
ProCarManuals.com

TEST SC-3BCONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-3B
CONTINUED FROM DISCONNECT THE ECM
THE PREVIOUS TURN IGNITION OFF. HARNESS
PAGE. CONNECTORS.**
OF THE SECONDARY REPAIR OPEN IN THE
USING AN OHMMETER, BRAKE LAMP SWITCH IS THE RESISTANCE NO SECONDARY BRAKE
MEASURE THE SIGNAL CIRCUIT. BELOW 5.0 OHMS? LAMP SWITCH SIGNAL
RESISTANCE...CIRCUIT.*
FIG.1
YES
THE BRAKE LAMP REPAIR SHORT TO
USING AN OHMMETER, SWITCH CONNECTOR IS THE RESISTANCE YES GROUND IN THE
MEASURE RESISTANCE CAVITY 1 AND GROUND. BELOW 5.0 OHMS? SECONDARY BRAKE
BETWEEN... LAMP SWITCH SIGNAL
FIG.2 CIRCUIT.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
385
ProCarManuals.com