ignition CHRYSLER CARAVAN 2000 Repair Manual

TEST TC-59ACONTINUED - REPAIRING - INDUCTIVE AUXILIARY SPEED SENSOR STATIC
PLAUSIBILITY
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-59A TURN IGNITION OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS NEEDLE MOVEMENT
PAGE. SENSOR HARNESS
CONNECTOR.*
INSPECT THE NEDLE THE SENSOR HARNESS
MOVEMENT SENSOR AND THE ENGINE IS THERE DAMAGE OR YES REPAIR AS
CONNECTOR AT HARNESS. CORROSION AT NECESSARY.*
BOTH... EITHER HARNESS?
FIG.1 AND 2.
NO
CHECK THE WIRING THIS INTERFERENCE
HARNESS FOR COULD BE CAUSED BY IS THE WIRING YES REAPIR AS
MIS-ROUTING THAT LARGE CURRENT HARNESS NECESSARY.*
COULD CAUSE CARRYING WIRES OR MIS-ROUTED?
INTERFERNCE. THE ALTERNATOR.
NO
USING AN OHMMETER, REPAIR THE OPEN IN
DISCONNECT THE ECM MEASURE THE NEEDLE IS THE RESISTANCE YES THE NEEDLE
HARNESS MOVEMENT SENSOR ABOVE 5.0 OHMS? MOVEMENT SENSOR
CONNECTORS.** SIGNAL CIRCUIT. SIGNAL CIRCUIT.*
FIG.3
NO
REPLACE THE NEEDLE START AND OPERATE
MOVEMENT SENSOR. THE ENGINE FROM DOES THE CODE YES REPLACE THE ENGINE
RECONNECT ALL IDLE TO 3500 RPM RESET? CONTROL MODULE.*
CONNECTORS. KEY WHILE MONITORING
ON. ERASE CODES. THE DRB.
NO
TEST COMPLETE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
215
ProCarManuals.com

TEST TC-62ACONTINUED - REPAIRING - INTAKE AIR TEMPERATURE SENSOR SIGNAL HIGH
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-62A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS BOOST PRESSURE
PAGE. SENSOR HARNESS
CONNECTOR.**
WITH A JUMPER WIRE, TURN IGNITION ON.
DISCONNECT THE ECM REMOVE THE DIESEL CONNECT DIESEL POWER
HARNESS POWER RELAY.** RELAY CONN. CAVITIES USE A VOLTMETER IN
CONNECTORS.** 30 AND 87 (IN PDC). THE FOLLOWING
FIG.1 STEP.
MEASURE THE IAT REPAIR THE INTAKE
SENSOR SIGNAL IS THE VOLTAGE YES AIR TEMPERATURE
CIRCUIT. ABOVE 1.0 VOLT? SENSOR SIGNAL
CIRCUIT FOR A
FIG.2 SHORT TO VOLTAGE.*
NO
KEY OFF. USING AN OHMMETER, REPAIR THE OPEN
MEASURE THE IAT IS THE RESISTANCE NO INTAKE AIR
REMOVE THE JUMPER SENSOR SIGNAL BELOW 5.0 OHMS? TEMPERATURE SENSOR
WIRE. CIRCUIT. SIGNAL CIRCUIT.*
FIG.3
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN THE INTAKE WITH THE DRB, DISPLAY "INTAKE YES REPLACE THE BOOST
AIR TEMP SENSOR ERASE AND THEN AIR TEMPERATURE PRESSURE SENSOR.*
SIGNAL AND SENSOR READ CODES. SENSOR LOW
GROUND CKT. FIG.1 EXCEEDED"?
NO
MOVE THE JUMPER DOES THE DRB
WIRE FROM THE WITH THE DRB, READ DISPLAY "INTAKE YES REPAIR THE OPEN
SENSOR GROUND TO CODES. AIR TEMPERATURE SENSOR GROUND
AN ENGINE GROUND. SENSOR LOW CIRCUIT.*
EXCEEDED"?
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
219
ProCarManuals.com

TEST TC-72AREPAIRING - NEEDLE MOVEMENT SENSOR SRC HIGH EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
WITH THE DRB ERASE TURN IGNITION ON AND
START TEST CODES. TURN READ CODES. DOES THE YES CONTINUE TEST
TC-72A. IGNITION OFF FOR DRB DISPLAY "NEEDLE TC-72A ON THE
10 SECONDS. MOVEMENT SENSOR SRC NEXT PAGE.
HIGH EXCEEDED"?
NO
USING THE SCHEMATIC DOES THE DRB REPAIR THE HARNESS
AS A GUIDE, WIGGLE MONITOR THE DRB DISPLAY "NEEDLE YES OR CONNECTOR THAT
THE SENSOR CONNECTOR DISPLAY. MOVEMENT SENSOR CAUSED THE CODE TO
& HARNESS. SRC HIGH SET.*
FIG.1 EXCEEDED"?
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
225
ProCarManuals.com

TEST TC-73AREPAIRING - NEEDLE MOVEMENT SENSOR SRC LOW EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
WITH THE DRB, TURN IGNITION ON AND
START TEST ERASE CODES. TURN READ CODES. DOES THE YES CONTINUE TEST
TC-73A. IGNITION OFF FOR DRB DISPLAY " NEEDLE TC-73A ON THE
10 SECONDS. MOVEMENT SENSOR SRC NEXT PAGE.
LOW EXCEEDED"?
NO
USING THE SCHEMATIC, DOES THE DRB REPAIR THE HARNESS
WIGGLE THE NEEDLE MONITOR THE DRB DISPLAY "NEEDLE YES OR CONNECTOR THAT
MOVEMENT SENSOR DISPLAY. MOVEMENT SENSOR CAUSED THE CODE TO
CONNECTOR & HARNESS. SRC LOW EXCEEDED"? SET.*
FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
229
ProCarManuals.com

TEST TC-74AREPAIRING - REDUNDANT EMERGENCY STOP PLAUSIBILITY IN AFTER-RUN
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TURN IGNITION ON,
ENGINE OFF. USING
THE DRB READ ECM
CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
233
ProCarManuals.com

TEST TC-75AREPAIRING - REDUNDANT EMERGENCY STOP POWERSTAGE DEFECTIVE
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST WITH THE DRB,
TC-75A. ERASE CODES.
CYCLE THE IGNITION DOES THE DRB
ON AND OFF SEVERAL WITH THE IGNITION DISPLAY "REDUNDANT YES CONTINUE TEST
TIMES, PAUSING FOR ON ENGINE OFF, EMERG STOP TC-75A ON THE
TEN SECONDS AT KEY READ CODES. POWERSTAGE NEXT PAGE.
ON AND OFF. DEFECTIVE"?
NO
AT THIS TIME THE REVIEW THE CIRCUIT
CONDITION FOR DESCRIPTION FOR A WERE ANY PROBLEMS YES REPAIR AS
SETTING THE CODE PROPER UNDERSTANDING FOUND? NECESSARY.*
IS NOT PRESENT. OF THIS CODE. CHECK
FIG.1 FOR PROBLEMS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
237
ProCarManuals.com

TEST TC-79AREPAIRING - SOLENOID VALVE CONTROLLER OPEN CIRCUIT
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY ON, READ CODES.
START TEST TURN IGNITION OFF. DOES THE DRB DISPLAY YES CONTINUE TEST
TC-79A. WITH THE DRB, "SOLENOID VALVE TC-79A ON THE
ERASE CODES. CONTROLLER OPEN NEXT PAGE.
CIRCUIT"?
NO
USE THE SCHEMATIC AS DOES THE DRB REPAIR THE HARNESS
A GUIDE AND WIGGLE MONITOR THE DRB DISPLAY "SOLENOID YES OR CONNECTOR THAT
THE SOLENOID VALVE DISPLAY. VALVE CONTROLLER CAUSED THE CODE TO
CONNECTOR & HARNESS. OPEN CIRCUIT"? SET.*
FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
243
ProCarManuals.com

TEST TC-79ACONTINUED - REPAIRING - SOLENOID VALVE CONTROLLER OPEN CIRCUIT
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-79A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS FUEL PUMP ASSEMBLY
PAGE. HARNESS
CONNECTOR.**
KEY ON. MEASURE FUEL
USE A VOLTMETER IN PUMP HARNESS IS THE VOLTAGE YES REPAIR THE OPEN
THE FOLLOWING CONNECTOR CAVITY 10. BELOW 10.5 VOLTS? DIESEL POWER RELAY
STEP.OUTPUT CIRCUIT*
FIG.1
NO
TURN IGNITION OFF. USING AN OHMMETER, REPAIR THE FUEL
DISCONNECT THE ECM MEASURE THE FUEL IS THE RESISTANCE YES TIMING SOLENOID
HARNESS TIMING SOLENOID BELOW 5.0 OHMS? CONTROL CIRCUIT
CONNECTORS.** CONTROL CIRCUIT TO FOR A SHORT TO
GROUND. FIG.1 GROUND.*
NO
MEASURE THE FUEL REPAIR THE OPEN
USE AN OHMMETER IN TIMING SOLENOID IS THE RESISTANCE YES FUEL TIMING
THE FOLLOWING CONTROL CKT BETWEEN ABOVE 5.0 OHMS? SOLENOID CONTROL
STEPS. THE ECM AND THE FUEL CIRCUIT.*
PUMP ASSEMBLY. FIG.2
NO
MEASURE THE PUMP CONNECTOR (PUMP
RESISTANCE OF THE SIDE) BETWEEN IS THE RESISTANCE NO REPLACE THE FUEL
FUEL TIMING CAVITIES 5 AND 10. BETWEEN 12.0 AND INJECTION PUMP
SOLENOID AT THE 20.0 OHMS? ASSEMBLY.*
INJECTION... FIG.3
YES
NOTE: BEFORE
REPLACING THE ECM, DID THE FUEL YES REPLACE THE ENGINE
PERFORM TEST NTC-3A INJECTION PUMP CONTROL MODULE.*
TO CHECK INTERNAL PASS TEST NTC-3A?
FUEL PUMP CIRCUITRY.
NO
REPLACE THE FUEL
INJECTION PUMP
ASSEMBLY.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
245
ProCarManuals.com

TEST TC-80AREPAIRING - SOLENOID VALVE CONTROLLER SHORT CIRCUIT
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY ON, READ CODES.
START TEST WITH THE DRB, DOES THE DRB DISPLAY YES CONTINUE TEST
TC-80A. ERASE CODES. TURN "SOLENOID VALVE TC-80A ON THE
IGNITION OFF. CONTROLLER SHORT NEXT PAGE.
CIRCUIT"?
NO
USE THE SCHEMATIC AS DOES THE DRB REPAIR THE HARNESS
A GUIDE AND WIGGLE MONITOR THE DRB DISPLAY "SOLENOID YES OR CONNECTOR THAT
THE SOLENOID VALVE DISPLAY. VALVE CONTROLLER CAUSED THE CODE TO
CONNECTOR & HARNESS. SHORT CIRCUIT"? SET.*
FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
247
ProCarManuals.com

TEST TC-84AREPAIRING - TERMINAL 15 PLAUSIBILITY AFTER START-UP
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST WITH THE DRB,
TC-84A. ERASE CODES.
CYCLE THE IGNITION
ON AND OFF SEVERAL WITH THE IGNITION DOES THE DRB YES CONTINUE TEST
TIMES, PAUSING FOR ON ENGINE OFF, DISPLAY "TERMINAL TC-84A ON THE
TEN SECONDS AT KEY READ CODES. 15 PLAUSIBILITY"? NEXT PAGE.
ON AND OFF.
NO
AT THIS TIME THE REVIEW THE CIRCUIT
CONDITION FOR DESCRIPTION FOR A WERE ANY PROBLEMS YES REPAIR AS
SETTING THE CODE PROPER UNDERSTANDING FOUND? NECESSARY.*
IS NOT PRESENT. OF THIS CODE. CHECK
FIG. 1 FOR PROBLEMS.
NO
TEST COMPLETE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
259
ProCarManuals.com