radio CHRYSLER CONCORDE 2004 2.G Owners Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2004, Model line: CONCORDE, Model: CHRYSLER CONCORDE 2004 2.GPages: 273, PDF Size: 6 MB
Page 21 of 273
one second. Release both buttons simultaneously. You
will hear a chime to signal that you can proceed with
programming the new transmitter.
3. One by one with each transmitter (includes previously
programmed as well as the new transmitter), press and
release the lock and unlock buttons simultaneously. You
will hear a chime after each transmitter has been success-
fully programmed. You will have 30 seconds to finish
programming all new transmitters. A chime will sound
when the 30 seconds is over or the ignition switch is
turned to the Lock position.
Transmitter Linked to Memory Programming
Your remote transmitters can be programmed to return
the driver’s seat, mirrors, and radio presets to the saved
position when the Unlock button is pressed and released.
NOTE:When newly purchased (or replacement) trans-
mitters are programmed into the vehicle, the first trans-
mitter programmed will be associated with memory
setting 1, and the second transmitter programmed will be
associated with memory setting 2. Additional transmit-
ters will not be associated with a memory setting.To program your transmitters, perform the following:
1. Insert key into the igniton and turn the key to the
On/Run position.
2. Adjust the seat and side view mirrors to the desired
position. Program the radio preset buttons to the desired
stations.
3. Press and release the Set (S) button on the memory
seat switch, then press and release memory button 1 or 2.
4. Press and release the Lock button on the transmitter.
This will link the transmitter to the desired memory
setting.
5. Do not press any buttons for 10 seconds.
NOTE:Your transmitters may be unlinked from your
memory settings by following the procedure above ex-
cept pressing the Unlock button on the transmitter in step
4 above. On vehicles equipped with an EVIC (Electronic
Vehicle Information Center), these functions can be se-
lected at the EVIC using the Customer Programmable
Features. Refer to EVIC-Customer Programmable Fea-
tures for details. When newly purchased (or replacement)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
2
Page 22 of 273
transmitters are programmed into the vehicle, the first
transmitter trained will be associated with memory set-
ting 1, and the second transmitter trained will be associ-
ated with memory setting 2. Additional transmitters will
not be associated with a memory setting.
General Information
This transmitter complies with FCC rules part 15 and
with RS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not
cause harmful interference and (2) This device must
accept any interference that may be received, including
interference that may cause undesired operation.
If your Remote Lock Control fails to operate from a
normal distance, check for these two conditions:
1. Weak batteries in transmitter. The expected life of
batteries is from one to two years.
2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, and some mobile or CB radios.
Transmitter Battery Service
The recommended replacement battery is DL 2016 or its
equivalent.
•Pry the transmitter halves apart with a dime or similar
object. Make sure not to damage the rubber gasket
during removal.
•Remove and replace the batteries. Avoid touching the
new batteries with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it
with rubbing alcohol.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 61 of 273
Lumbar Support
This feature allows you to increase or decrease the
amount of lumbar support. Turn the control level for-
ward to increase and rearward to decrease the desired
amount of lumbar support.
Heated Seats— If Equipped
The front driver’s and passenger seats are heated. The
control for the heater is located on the outboard side of
each seat. After turning on the ignition, you can choose
from High, Off, or Low heat settings. An indicator on the
switch shows which setting has been chosen.Press the switch once to select a heat setting (high or low)
and press the switch a second time to turn the heated seat
off.
NOTE:Once a heat setting is selected, heat will be felt
within 2 to 3 minutes.
Memory Feature
This feature allows the driver to recall one of two
pre-selected seat/outside mirror settings as well as radio
station preset buttons. The radio display will show which
memory position is being recalled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61
3
Page 62 of 273
The memory feature switch is located on the outboard
side of the driver’s seat, next to the heated seat switch.
To Set The Memory Feature:
1. Use the seat and driver mirror switches to adjust the
seat and driver mirror to the desired positions. Program
the radio preset buttons to the desired stations.
2. Press and release the Set (S) button on the memory
seat switch, then press either button 1 or 2 within 5
seconds. The radio display will show which memory
position is being set.3. A second memory setting can be stored in the vehicle
memory. Begin with pressing 2 on the memory seat
switch for driver 2. Select a second seat/radio setting,
press the Set (S) button, then press button 2 within 5
seconds.
Each time the Set and a numbered button are pressed, the
old memory is erased, and a new one is stored.
NOTE:The vehicle must be in Park to activate the
Memory feature.
Programming the Remote Keyless Transmitter for
the Memory Feature
Your remote transmitters can be programmed to return
the driver’s seat, mirror, and radio presets to the saved
position when the Unlock button is pressed and released.
To program your transmitters, perform the following:
1. Insert the key into the ignition and turn the key to the
Run position.
2. Adjust the seat and side view mirror to the desired
position. Program the radio preset buttons to the desired
stations.
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 65 of 273
WARNING!
If the hood is not fully latched, it could fly up when
the vehicle is moving and block your forward vision.
You could have a collision. Be sure all hood latches
are fully latched before driving.
INTERIOR LIGHTS
To Turn The Interior Lights On:
Rotate the Dimmer Control upward to the second detent.
Rotate the switch downward to turn the interior lights
off.
NOTE:The interior lights have a “fade to off” feature.
When the lights are turned off, they gradually “fade” off.
Battery Saver Feature—Interior Lights
The interior courtesy lights come on when a door is open
or left ajar. To prevent battery drain, if you leave a door
open or ajar these lights will turn off after 15 minutes.
After you close the door, the interior courtesy lights will
again function in the normal matter.
NOTE:The map lights or reading lights that are manu-
ally switched on will not turn off automatically.
Instrument Panel Lighting
The brightness of the instrument panel lighting can be
regulated by rotating the dimmer switch.
Daytime Brightness Feature
Certain instrument panel components can be illuminated
at full brightness during the daytime. These are the
Odometer, Transmission Range Indicator, Radio, Climate
Controls, and the Overhead Travel Information Center.
This can be helpful when driving with your headlights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65
3
Page 90 of 273
Auto Door Locks
When this feature is selected, all doors lock automatically
when the speed of the vehicle reaches 15 mph (25 km/h).
Pressing the STEP button when in this display will select
“Yes” or “No.”
Auto Unlock On Exit (Available Only When the
AUTO DOOR LOCKS Feature is Turned On )
When this feature is selected all the vehicle’s doors will
unlock when the driver’s door is opened if the vehicle is
stopped and the transmission is in P (Park) or N (Neu-
tral) position. Pressing the STEP button when in this
display will select “Yes” or “No.”
Remote Unlock Driver’s Door 1st
When this feature is selected only the driver’s door will
unlock on the first press of the remote keyless entry
unlock button and require a second press to unlock the
remaining locked door. WhenREMOTE UNLOCK ALL
DOORSis selected all of the doors will unlock at the first
press of the remote keyless entry unlock button. Pressing
the STEP button when in this display will select DRIV-
ER’S DOOR 1ST or ALL DOORS.
Remote Linked To Memory (Available with
Memory Seat Only)
When this feature is selected the memory seat, mirror,
and radio settings will return to the memory set position
when the remote keyless entry “Unlock” button is
pressed. If this feature is not selected then the memory
seat, mirror, and radio settings can only return to the
memory set position using the door mounted switch.
Pressing the STEP button when in this display will select
“Yes” or “No.”
Sound Horn with Lock
When this feature is selected a short horn sound will
occur when the remote keyless entry “Lock” button is
pressed. This feature may be selected with or without the
flash lights on lock/unlock feature. Pressing the STEP
button when in this display will select “Yes” or “No.”
Flash Lights with Lock/Unlock
When this feature is selected, the front and rear turn
signals will flash when the doors are locked or unlocked
using the remote keyless entry transmitter. This feature
may be selected with or without the sound horn on lock
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 101 of 273
UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
Instruments And Controls................105
Instruments And Controls
(Concorde Limited Only)
................106
Instrument Cluster.....................107
Instrument Cluster (Concorde Limited Only). . 108
Instrument Cluster Description............109
Setting The Analog Clock—If Equipped.....113
Electronic Digital Clock.................113
▫Clock Setting Procedure.................114
Sales Code RAZ—AM/ FM Stereo Radio With
Cassette Tape Player And CD Player — If
Equipped
............................114
▫Operating Instructions — Radio...........114▫Power Switch, Volume Control............114
▫Seek Button (Radio Mode)...............115
▫Tuning.............................115
▫PTY (Program Type) Button..............115
▫Balance............................116
▫Fade..............................116
▫Tone Control........................116
▫AM/FM Selection.....................117
▫Scan Button.........................117
▫To Set The Radio Push-Button Memory......117
▫To Change From Clock To Radio Mode......117
▫Operating Instructions — Tape Player.......117
4
Page 102 of 273
▫Seek Button.........................118
▫Fast Forward (FF).....................118
▫Rewind (RW)........................118
▫Tape Eject...........................118
▫Scan Button.........................118
▫Changing Tape Direction................118
▫Metal Tape Selection...................118
▫Pinch Roller Release...................118
▫Noise Reduction......................119
▫Operating Instructions — CD Player........119
▫Inserting The Compact Disc..............119
▫Seek Button.........................119
▫EJT CD (Eject) Button..................120
▫FF/Tune/RW Button...................120
▫Program Button 4 (Random Play)..........120
▫Mode..............................120▫Tape CD Button......................121
▫Time Button.........................121
▫Scan Button.........................121
Sales Code RBB—AM/FM Stereo Radio With
Cassette Tape Player And CD Changer
Capability
...........................121
▫Operating Instructions..................121
▫Power Button........................122
▫Electronic Volume Control...............122
▫Seek..............................122
▫Tune ..............................122
▫To Set The Push-Button Memory..........122
▫Balance............................123
▫Fade..............................123
▫Bass And Treble Tone Control............123
▫AM/FM Selection.....................123
102 UNDERSTANDING YOUR INSTRUMENT PANEL
Page 103 of 273
▫Mode Button........................123
▫Cassette Player Features................123
▫CD Changer Control Capability — If
Equipped...........................124
▫Radio Display Messages................126
Sales Code RBK—AM/ FM Stereo Radio With
CD Player And CD Changer Controls
.......126
▫Radio Operation......................126
▫CD Player Operation...................128
▫CD Changer Operation — If Equipped......130
6 Disc CD Changer — If Equipped.........131
▫Loading The CD Changer...............131
▫Playing Discs........................131
▫Seek Button.........................132
▫FF/Tune/RW........................132
▫Mode Button........................132▫Program Button 1.....................132
▫Program Button 4 (Random Play)..........132
▫Program Button 5.....................132
▫Time Button.........................132
▫Changing Modes......................132
▫Removing Discs From The CD Changer.....133
▫CD Changer Operation With The Changer
Off ...............................133
Remote Sound System Controls — If
Equipped
............................133
▫Radio Operation......................134
▫Tape Player.........................134
▫CD Player — Single Disc In Radio.........134
▫CD Player — 6 Disc CD Changer..........134
Cassette Tape And Player Maintenance......135
Compact Disc Maintenance...............136
UNDERSTANDING YOUR INSTRUMENT PANEL 103
4
Page 104 of 273
Radio Operation And Cellular Phones.......136
Climate Controls......................137
▫Manual Air Conditioning/Heater Operation . . 137▫Automatic Temperature Control (ATC) — If
Equipped...........................140
104 UNDERSTANDING YOUR INSTRUMENT PANEL