engine oil CHRYSLER PT CRUISER 2008 1.G User Guide

Check ventilation hose for indication of damage or
plugging deposits. Replace if necessary.FUEL FILTERA plugged fuel filter can cause hard starting or limit the
speed at which a vehicle can be driven. Should an
excessive amount of dirt accumulate in the fuel tank,
frequent filter replacement may be necessary. The fuel
filters are located inside the fuel tank. See your dealer for
service.AIR CLEANER ELEMENT (AIR FILTER)Under normal driving conditions, replace the filter at the
intervals shown on Schedule “A”. If, however, you drive
the vehicle frequently under dusty or severe conditions,
the filter element should be inspected periodically and
replaced if necessary at the intervals shown on Schedule
“B”.NOTE:
For vehicles with a Turbo engine, a small
amount of oil accumulation in the air cleaner box is
normal. The amount will depend on driving style. The air
cleaner box should be cleaned out and a new make-up-
air filter element should be installed during the normal
air filter maintenance procedure.
WARNING!
The air cleaner can provide a measure of protection
in the case of engine backfire. Do not remove the air
cleaner unless such removal is necessary for repair or
maintenance. Make sure that no one is near the
engine compartment before starting the vehicle with
the air cleaner removed. Failure to do so can result in
serious personal injury.
MAINTAINING YOUR VEHICLE 391
7

WARNING!
Fluid level should be checked on a level surface and
with the engine off to prevent injury from moving
parts and to insure accurate fluid level reading. Do
not overfill. Use only manufacturers recommended
power steering fluid.
If necessary, add fluid to restore to the proper indicated
level. With a clean cloth, wipe any spilled fluid from all
surfaces. Refer to Fluids, Lubricants, and Genuine Parts
for correct fluid types.FRONT SUSPENSION BALL JOINTSThere are two front suspension lower ball joints that are
permanently lubricated. Inspect these ball joints when-
ever under vehicle service is done. Damaged seals and
their corresponding potentially damaged ball joints must
be replaced.
STEERING LINKAGEThe tie rod end ball joints should be inspected for
external leakage and damage when other maintenance is
performed.BODY LUBRICATIONLocks and all body pivot points, including such items as
seat tracks, doors, liftgate and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should be
wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing other
underhood services, the hood latch, release mechanism
and safety catch should be cleaned and lubricated.
The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
MAINTAINING YOUR VEHICLE 395
7

amount of a high quality lubricant such as MoparLock
Cylinder Lubricant directly into the lock cylinder.WINDSHIELD WIPER BLADESClean the rubber edges of the wiper blades and the
windshield periodically with a sponge or soft cloth and a
mild non abrasive cleaner or use the washer solvent. This
will remove accumulations of salt, waxes or road film
and help reduce streaking and smearing.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield. Avoid using the wiper blades to
remove frost or ice from the windshield. make sure that
they are not frozen to the glass before turning them on to
avoid damaging the blade. Keep the blade rubber out of
contact with petroleum products such as engine oil,
gasoline, etc.
Windshield Wiper Blade Replacement1. Lift the wiper arm away from the glass.
2. Push the release tab shown in the illustration and slide
the wiper blade assembly down along the arm. Gently
place the wiper arm on the windshield.
3. Install the new blade assembly onto the wiper arm tip
until it locks in place.
NOTE: Always refer to the wiper blade packaging for
specific installation instructions. Many wiper blade re-
placements fit multiple vehicles.WINDSHIELD WASHER RESERVOIRNOTE: Always refer to the wiper blade packaging for
specific installation instructions. Many wiper blade re-
placements fit multiple vehicles.
The washer fluid reservoir is located in the rear of the
engine compartment on the passenger side and should be
396 MAINTAINING YOUR VEHICLE

checked for fluid level at regular intervals. Fill the
reservoir with windshield washer solvent (not radiator
antifreeze) and operate the system for a few seconds to
flush out the residual water.
WARNING!
Commercially available windshield washer solvents
are flammable. They could ignite and burn you. Care
must be exercised when filling or working around
the washer solution.EXHAUST SYSTEMThe best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
system.
If you notice a change in the sound of the exhaust system,
or if exhaust fumes can be detected inside the vehicle, orwhen the underside or rear of the vehicle is damaged;
have a competent technician inspect the complete ex-
haust system and adjacent body areas for broken, dam-
aged, deteriorated, or mispositioned parts. Open seams
or loose connections could permit exhaust fumes to seep
into the passenger compartment. In addition, inspect the
exhaust system each time the vehicle is raised for an oil
change or lubrication. Replace as required.
WARNING!
Exhaust gases can injure or kill. They contain carbon
monoxide (CO) which is colorless and odorless.
Breathing it can make you unconscious and can
eventually poison you. To avoid breathing CO, refer
to Exhaust Gas in the Safety Tips section of this
manual.
MAINTAINING YOUR VEHICLE 397
7

brittle rubber, cracking, tears, cuts, abrasions, and exces-
sive swelling suggest deterioration of the rubber. Particu-
lar attention should be made to examining those hose
surfaces nearest to high heat sources, such as the exhaust
manifold.
Inspect all hose clamps and couplings to make sure they
are secure and no leaks are present.
Insure nylon tubing in these areas has not melted or
collapsed.
NOTE:Often, fluids such as oil, power steering fluid,
and brake fluid are used during assembly plant opera-
tions to ease the assembly of hoses to couplings. There-
fore, oil wetness at the hose-coupling area is not neces-
sarily an indication of leakage. Actual dripping of hot
fluid when systems are under pressure (during vehicle
operation) should be noted before a hose is replaced
based on leakage. NOTE:
Inspection of brake hoses should be done when-
ever the brake system is serviced and at every engine oil
change. Inspect hydraulic brake hoses for surface crack-
ing, scuffing, or worn spots. If there is any evidence of
cracking, scuffing, or worn spots, the hose should be
replaced immediately! Eventual deterioration of the hose
can take place resulting in a possibility of a burst failure.
WARNING!
Worn brake hoses can burst and cause brake failure.
You could have an accident. If you see any signs of
cracking, scuffing, or worn spots, have the brake
hoses replaced immediately.
MAINTAINING YOUR VEHICLE 405
7

WARNING!
Use of a brake fluid that has a lower initial boiling
point than the recommended MOPARDOT 3 prod-
uct or a brake fluid that is unidentified as to FMVSS
specification may result in sudden brake failure
during hard prolonged braking. You could have an
accident.
CAUTION!
Use of improper brake fluids will affect overall
clutch system performance. Improper brake fluids
may damage the clutch system resulting in loss of
clutch function and the ability to shift the transaxle.
WARNING!
Overfilling the brake fluid reservoir can result in
spilling brake fluid on hot engine parts and the
brake fluid catching fire.
Use only brake fluid that has been in a tightly closed
container to avoid contamination from foreign matter.
CAUTION!
Do not allow petroleum base fluid to contaminate the
brake fluid, all brake seal components could be
damaged causing partial or complete brake failure.
MAINTAINING YOUR VEHICLE 407
7

FLUIDS AND CAPACITIES
FLUIDS AND CAPACITIESU.S. Metric
Fuel (Approximate) 15 Gallons56.7 Liters
Engine Oil-With Filter
2.4 Liter Engines (Use API Certified
SAE 5W-30 Engine Oil.) 5.0 qts
4.7 Liters
Cooling System *
2.4 Liter Engines (Mopar
Antifreeze/Coolant 5 Year/100,000
Miles Formula), or equivalent. 6.5 qts
6.2 Liters
* Includes heater and coolant recovery bottle filled to MAX level.
MAINTAINING YOUR VEHICLE 429
7

FLUIDS, LUBRICANTS AND GENUINE PARTS
ENGINE
FLUIDS, LUBRICANTS AND GENUINE PARTS
Component Fluids, Lubricants and Genuine Parts
Engine Coolant Mopar
Antifreeze/Coolant 5 Year/100,000 Mile For-
mula HOAT (Hybrid Organic Additive Technology) or
equivalent.
Engine Oil (2.4L Standard, 2.4L Standard Turbo) Use API Certified SAE 5W-30 Engine Oil. Refer to your
engine oil filler cap for correct SAE grade meeting
DaimlerChrysler Material Standard MS-6395.
Engine Oil Filter Non Turbo—Mopar
4105409AB or equiv.
Turbo—Mopar 4781452BB or equiv.
Spark Plugs 2.4L Non Turbo — Champion
RE16MC, 040” Gap 2.4L
Turbo — Champion RE14MCC5,.050” Gap.
Fuel Selection 87 Octane for 2.4L Standard Turbo and 2.4L Standard
Non Turbo Engines.
430 MAINTAINING YOUR VEHICLE

•
Taxi, police, or delivery service (commercial ser-
vice).†

•
Off-road or desert operation.
•
If equipped for and operating with E-85 (ethanol)
fuel.
NOTE: IfANY of these apply to you then change your
engine oil every 3,000 miles (5 000 km) or 3 months,
whichever comes first, and follow schedule “B—All
Engines” of the Maintenance Schedules section of this
manual.
NOTE: IFANY of these apply to you then flush and
replace the engine coolant every 102,000 miles (170 000
km) or 60 months, whichever comes first, and follow
schedule “B—All Engines” of the Maintenance Sched-
ules section of this manual.
NOTE: Most vehicles are operated under the conditions
listed for Schedule B—ALL ENGINES. Second is Schedule
“A”—NON TURBO. It is for vehicles
that are not operated under any of the conditions listed
under Schedule B—ALL ENGINES.
Third is Schedule “A”—TURBO. It is for vehicles that are
not operated under any of the conditions listed under
Schedule B—ALL ENGINES.
Use the schedule that best describes your driving condi-
tions. Where time and mileage are listed, follow the
interval that occurs first.
CAUTION!
Failure to perform the required maintenance items
may result in damage to the vehicle.
MAINTENANCE SCHEDULES 435
8M A I
N T
E
N A
N CE
S
C
H E
D
U L
E
S

At Each Stop for Fuel•
Check the engine oil level about 5 minutes after a fully
warmed engine is shut off. Checking the oil level while
the vehicle is on level ground will improve the accu-
racy of the oil level reading. Add oil only when the
level is at or below the ADD or MIN mark.
•
Check the windshield washer solvent and add if
required.
Once a Month
•
Check tire pressure and look for unusual wear or
damage.
•
Inspect the battery and clean and tighten the terminals
as required.
•
Check the fluid levels of coolant reservoir, brake
master cylinder and transaxle and add as needed.
•
Check all lights and all other electrical items for correct
operation.
•
Check rubber seals on each side of the radiator for
proper fit.
At Each Oil Change
•
Change the engine oil filter.
•
Inspect the exhaust system.
•
Inspect the brake hoses.
•
Inspect the CV joints and front suspension compo-
nents.
•
Check the automatic transaxle fluid level.
•
Check the manual transaxle fluid level and fill plug
condition.
•
Check the coolant level, hoses, and clamps.
436 MAINTENANCE SCHEDULES
8M A I
N T
E
N A
N CE
S
C
H E
D
U L
E
S