Security CHRYSLER VOYAGER 1996 Owner's Manual

TN/BK18 G78
BK20Z1
G400
SWITCH AJAR
LIFTGATE
3
1
Z1
18
BK
G301
G70
18
BR/TN
C143SENSE SWITCHAJAR HOOD
L16 J03A4
TN/BK18 G78
4B17
LJ01
SENSE SWITCHAJAR LIFTGATE
59C1
TN/BK18 G78
G302
BK18Z1BK18Z1REAR RIGHT
C177
DOOR
AJAR
SWITCH
SENSE
G76
18
TN/YL
TN/OR18 G77
2
SWITCH AJAR
HOOD
12
RIGHT
REAR
DOOR
AJAR
SWITCH
11
SWITCH AJAR
DOOR
REAR
LEFT
2
SENSE SWITCHAJAR DOOR
47C1
MODULE
CONTROL
BODY
LEFT
REAR
814 1211
(8W-15-14) (8W-15-10) (8W-15-13)(8W-45-7)
(8W-45-8)
8W - 39 - 4 8W-39 VEHICLE THEFT SECURITY SYSTEMNS/GS
J988W-3GS003904

18FUSE15A
BATT A0
12
CENTER
DISTRIBUTION
POWER
2C2
15C2
F41
20
PK/VT
20C3
PTC
1
9A
ST-RUN A21
BLOCK JUNCTION
C4
19
MODULE IMMOBILIZER
KEY
SENTRY
1F41
20
PK/VT3
F87
20
WT/BK
FUSED
B(+)FUSED
IGNITION
(ST-RUN)
CCD
BUS
(+) (-)BUS CCD
GROUND
Z2
20
BK
G200
2 56
D1
20
VT/BR
D2
20
WT/BK
TO
PS01
TO
PS02
(8W-10-20)(8W-10-8)
(8W-10-9)
(8W-12-13)(8W-10-16)
(8W-12-2)
(8W-15-4)
(8W-30-4) (8W-30-4)
NS/GS8W-39 VEHICLE THEFT SECURITY SYSTEM
BUILT-UP-EXPORT8W - 39 - 5
GS003905J988W-3

INSTALLATION
NOTE: The screws attaching the door latch to the
door end frame have nylon patches on the threads.
All screws must be replaced when the latch has
been removed.
(1) Place door latch in position on door end frame.
(2) Install screws to hold door latch to door end
frame.
(3) Insert linkage into door latch.
(4) Engage clips to hold linkage to door latch.
(5) Connect wire connector into power door lock
motor, if equipped.
(6) Insert a hex wrench through the elongated hole
located in the door shut face above the latch.
(7) Loosen allen head screw.
(8) Pull outward on the outside door handle and
release.
(9) Tighten allen head screw.
(10) Verify door latch and power door lock opera-
tion.
(11) Install water shield and front door trim panel.
FRONT DOOR LATCH STRIKER
REMOVAL
(1) Mark outline of door striker on B-pillar to aid
in installation.
(2) Remove screws holding door latch striker to
B-pillar (Fig. 19).
(3) Remove door latch striker from vehicle.
(4) Retrieve any shims found between latch striker
and B-pillar.
INSTALLATION
(1) Position latch striker and any shims retrieved
on vehicle.
(2) Loosely install screws to hold latch striker to
B-pillar.
(3) Align latch striker to outline on B-pillar made
previously.
(4) Tighten all fasteners.
(5) Verify door fit and operation. Adjust latch
striker as necessary.
FRONT DOOR LOCK CYLINDER
REMOVAL
(1) Remove front door trim panel and water shield
as necessary to gain access to the outside door han-
dle.
(2) Roll door glass up.
(3) Through access hole at rear of inner door
panel, disconnect vehicle theft Security System
(VTSS) switch connector from door harness, if
equipped.
(4) Disengage push-in fasteners holding VTSS
switch harness to inner door reinforcement bar, if
equipped.
(5) Disengage clip holding door latch linkage to
door latch.
(6) Remove latch linkage from latch.
(7) Disengage clip holding door lock linkage to
door latch.
(8) Remove lock linkage from latch.
(9) Remove nuts holding outside door handle to
door outer panel (Fig. 23).
(10) Remove outside door handle from vehicle.
(11) Disengage clip holding lock cylinder into out-
side handle (Fig. 20).
(12) Pull lock cylinder from door handle.
Fig. 19 Door Latch StrikerFig. 20 Remove Front Door Lock Cylinder
23 - 32 BODYNS
REMOVAL AND INSTALLATION (Continued)

INSTALLATION
(1) Engage clip into outside handle to hold lock
cylinder.
(2) With link arm toward rear of vehicle, push lock
cylinder into door handle until clip snaps into place
(Fig. 21).
(3) Insert lock linkage into door latch.
(4) Engage clip to hold door lock linkage to latch.
(5) Insert latch linkage into door latch.
(6) Engage clip to hold door latch linkage to latch.
(7) Install push-in fasteners to hold VTSS switch
harness to inner door reinforcement bar, if equipped.
(8) Connect VTSS switch connector into door har-
ness, if equipped.
(9) Verify door latch operation.
(10) Install water shield and door trim panel.
FRONT DOOR OUTER BELT MOLDING
REMOVAL
(1) Remove door trim panel.
(2) Roll door glass down.
(3) Using a hook tool, disengage interlocking lip at
the base of the inward edge of the belt molding (Fig.
22).
(4) Remove belt molding from door.
INSTALLATION
(1) Place belt molding in position on door.
(2) Engage interlocking lip at the base of the
inward edge of the belt molding on door panel.
(3) Install door trim panel.
FRONT DOOR OUTSIDE HANDLE
REMOVAL
(1) Remove front door trim panel and water shield
as necessary to gain access to the outside door han-
dle.
(2) Roll door glass up.(3) Through access hole at rear of inner door
panel, disconnect vehicle theft Security System
(VTSS) switch connector from door harness, if
equipped.
(4) Disengage push-in fasteners holding VTSS
switch harness to inner door reinforcement bar, if
equipped.
(5) Disengage clip holding door latch linkage to
door latch.
(6) Remove latch linkage from latch.
(7) Disengage clip holding door lock linkage to
door latch.
(8) Remove lock linkage from latch.
(9) Remove nuts holding outside door handle to
door outer panel (Fig. 23).
(10) Remove outside door handle from vehicle.
Fig. 21 Install Front Door Lock Cylinder
Fig. 22 Front Door Outer Belt Molding
Fig. 23 Front Door Outside Handle
NSBODY 23 - 33
REMOVAL AND INSTALLATION (Continued)