key CHRYSLER VOYAGER 2000 Diagnostic Manual

Symptom List:
P-1492 BATTERY TEMP SENSOR VOLTAGE TOO HIGH
P-1493 BATTERY TEMP SENSOR VOLTAGE TOO LOW
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P-1492 BATTERY TEMP SENSOR
VOLTAGE TOO HIGH.
When Monitored and Set Condition:
P-1492 BATTERY TEMP SENSOR VOLTAGE TOO HIGH
When Monitored: With the ignition key on.
Set Condition: The PCM senses the voltage from the BTS to be either below 0.1 volts or
above 4.9 volts for 3 seconds.
P-1493 BATTERY TEMP SENSOR VOLTAGE TOO LOW
When Monitored: With the ignition key on.
Set Condition: The PCM senses the voltage from the BTS to be either below 0.1 volts or
above 4.9 volts for 3 seconds.
POSSIBLE CAUSES
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, read the Trouble Codes.
Does the DRB show9Battery Temperature Sensor Voltage9with a run count of zero?All
Ye s®Replace the PCM.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
18
CHARGING
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Engine Running
With the DRB, read trouble codes.
Are there any Charging System trouble codes?All
Ye s®Refer to Symptom List for problems related to Charging.
Perform Powertrain Verification Test VER-3A.
No®Go To 5
5 Ignition Off
Using a Voltmeter, measure the voltage between the Generator Case and Battery (-)
side.
Caution: Ensure all Wires are clear of the engine's moving parts.
Start the engine.
Is the voltage above 0.4 volt?All
Ye s®Repair Generator Ground high resistance Generator Case to
Battery (-) side.
Perform Powertrain Verification Test VER-3A.
No®Go To 6
6 Ignition Off
Connect Voltmeter between the Generator (12V) B+ Terminal and the Battery (+)
side.
Caution: Ensure all Wires are clear of the engine's moving parts.
Start the engine.
Is the voltage above 0.4 volt?All
Ye s®Repair the B(+) Circuit for high resistance between the Generator
and Battery.
Perform Powertrain Verification Test VER-3A.
No®Go To 7
7 Turn engine off, ignition key on.
With the DRB, read Battery voltage and record.
Using a Voltmeter, measure Battery voltage B(+) to B(-) Terminal.
Record second voltage reading.
Compare the two voltage readings.
Is the voltage difference less than one volt?All
Ye s®Test Complete.
Perform Powertrain Verification Test VER-3A.
No®Go To 8
8 Ignition Off
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Using a voltmeter, measure the fused B(+) at PCM.
Is the voltage within one volt of the DRB recorded reading?All
Ye s®Repair the B(+) Circuit for high resistance between the PCM and
the Battery.
Perform Powertrain Verification Test VER-3A.
No®Go To 9
25
CHARGING
* CHECKING CHARGING SYSTEM OPERATION WITH NO DTC'S Ð
Continued
ProCarManuals.com

Symptom:
P-0106 BAROMETRIC PRESSURE OUT OF RANGE
When Monitored and Set Condition:
P-0106 BAROMETRIC PRESSURE OUT OF RANGE
When Monitored: With the ignition key on at less than 350 milliseconds and engine speed
at less than 255 RPM.
Set Condition: The PCM senses the voltage from the MAP sensor to be less than 2.196
volts but above 0.019 volt for 300 milliseconds
POSSIBLE CAUSES
MAP SENSOR 5V SUPPLY CIRCUIT OPEN
MAP SENSOR 5V SUPPLY CIRCUIT SHORT TO GROUND
MAP SENSOR SIGNAL CIRCUIT OPEN
MAP SENSOR SIGNAL CIRCUIT PARTIAL SHORT TO GROUND
MAP SENSOR WIRING HARNESS INTERMITTENT DEFECT
MAP SENSOR WIRING HARNESS OBSERVABLE DEFECT
MAP SENSOR DEFECTIVE
PCM DEFECTIVE (VOLTAGE HIGH)
PCM DEFECTIVE (VOLTAGE LOW)
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, read the MAP Sensor voltage.
Is the voltage below 2.2 volts?All
Ye s®Go To 2
No®Go To 11
2 Ignition Off
Disconnect the MAP Sensor Electrical Connector.
Turn the ignition on, engine not running.
Note: Check connectors - Clean/repair as necessary.
Using a Voltmeter, measure voltage of the 5-Volt Supply Circuit at the Map Sensor
Connector.
Is the voltage above 4.5 volts?All
Ye s®Go To 3
No®Go To 7
27
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0122 THROTTLE POSITION SENSOR VOLTAGE LOW
When Monitored and Set Condition:
P-0122 THROTTLE POSITION SENSOR VOLTAGE LOW
When Monitored: With the ignition on.
Set Condition: The TP sensor signal voltage goes below 0.16 volt.
POSSIBLE CAUSES
TPS 5-VOLT SUPPLY CIRCUIT OPEN
TPS SIGNAL CIRCUIT SHORT TO GROUND
TPS SIGNAL CIRCUIT SHORT TO SENSOR GROUND CIRCUIT
TPS WIRING HARNESS INTERMITTENT DEFECT
TPS WIRING HARNESS OBSERVABLE DEFECT
PCM DEFECTIVE (TPS)
THROTTLE POSITION SENSOR DEFECTIVE
THROTTLE POSITION SENSOR VOLTAGE CHANGE NOT SMOOTH
TRANSMISSION CONTROL MODULE DEFECTIVE (TPS)
TEST ACTION APPLICABILITY
1 Turn key on, engine off.
With the DRB, read the Throttle Position Sensor (TP Sensor) voltage.
Is the Throttle Position Sensor voltage below 0.16 volt?All
Ye s®Go To 2
No®Go To 8
2 Ignition Off
Disconnect the Throttle Position Sensor.
Note: Check connectors - Clean/repair as necessary.
Ignition On, Engine Not Running.
Measure the voltage at the 5-Volt Supply Circuit at TPS Connector.
Is the voltage below 4.0 volts?All
Ye s®Repair the open TP Sensor 5-Volt Supply Circuit.
Perform Powertrain Verification Test VER-5A.
No®Go To 3
45
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off
Disconnect the Throttle Position Sensor.
Note: Check connectors - Clean repair as necessary.
Ignition On, Engine Not Running.
With the DRB, read the Throttle Position Sensor voltage.
Is the voltage above 1.0 volt?All
Ye s®Replace the Throttle Position Sensor.
Perform Powertrain Verification Test VER-5A.
No®Go To 4
4 Ignition Off
Disconnect the Throttle Position Sensor.
Disconnect the Transmission Control Module.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the TP Sensor Signal Circuit and ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Throttle Position Sensor Signal Circuit for a short to
ground.
Perform Powertrain Verification Test VER-5A.
No®Go To 5
5 Ignition Off
Disconnect the Throttle Position Sensor.
Disconnect the Transmission Control Module.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the TP Sensor Signal Circuit and the Sensor Ground
Circuit.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Sensor Signal Circuit shorted to Sensor Ground
Circuit.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 Ignition Off
Disconnect the Throttle Position Sensor.
Disconnect the Transmission Control Module if equipped..
Note: Check connectors - Clean/repair as necessary.
Key On
With the DRB, read the Throttle Position Sensor voltage.
Is the voltage above 1.0 volt?All
Ye s®Replace the Transmission Control Module.
Perform Powertrain Verification Test VER-5A.
No®Go To 7
7 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-5A.
46
DRIVEABILITY
P-0122 THROTTLE POSITION SENSOR VOLTAGE LOW ÐContinued
ProCarManuals.com

Symptom:
P-0131 1/1 O2 SENSOR VOLTAGE SHORTED TO GROUND
When Monitored and Set Condition:
P-0131 1/1 O2 SENSOR VOLTAGE SHORTED TO GROUND
When Monitored: With the ignition key off, after the O2 Sensor cools down; and after the
next key on provided that it is a cold start (coolant temperature less than 38 degrees C
(100.4 degrees F)) and ambient temperature within 13 degrees C (7.2 degrees F) of coolant
temperature.
Set Condition: The upstream O2 Sensor Signal voltage is below 0.156 volt prior to O2
Sensor Heater test (cool down period), and O2 voltage less than 0.156 volt after the key on
in the subsequent start.
POSSIBLE CAUSES
1/1 02 SENSOR VOLTAGE LOW
1/1 O2S SIGNAL CIRCUIT SHORT TO GROUND
1/1 O2S SIGNAL CKT SHORT TO GROUND CIRCUIT
1/1 O2 SENSOR DEFECTIVE
PCM DEFECTIVE (1/1 O2S)
TEST ACTION APPLICABILITY
1 Ignition Off
Turn ignition on.
With the DRB, monitor the Upstream O2 Sensor voltage for a few minutes.
Wait three minutes or until the voltage stabilizes (between 0.4 and 0.6 volt).
With the DRB, monitor the Upstream O2 Sensor voltage.
Is the Upstream O2 Sensor voltage below 0.156 volt?All
Ye s®Go To 2
No®The condition required to set this trouble code is not present at
this time.
Perform Powertrain Verification Test VER-5A.
2 Ignition Off
Disconnect the Upstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Key on.
With the DRB, monitor the Upstream O2 Sensor voltage.
Is the Upstream O2 Sensor voltage below 0.156 volts?All
Ye s®Go To 3
No®Replace the Upstream O2 Sensor.
Perform Powertrain Verification Test VER-5A.
53
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0135 O2S HEATER FAILURE
When Monitored and Set Condition:
P-0135 O2S HEATER FAILURE
When Monitored: With the ignition key off, after the engine cools down.
Set Condition: No sensor output signal is received when the PCM powers up the sensor
heater.
POSSIBLE CAUSES
1/1 O2 SENSOR CONNECTOR DAMAGED
1/1 O2 SENSOR GND CIRCUIT OPEN
ASD RELAY OUTPUT CIRCUIT OPEN
1/1 O2 SENSOR FAILURE
1/1 O2 SENSOR HEATER ELEMENT FAILURE
1/1 O2S HEATER FAILURE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the GLOBAL GOOD TRIP counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 3
2 Turn Ignition On (Engine Off), wait three minutes.
With the DRB , monitor the O2 Sensor voltage for a few minutes until the voltage
stabilizes between .4 and .6 volts.
With the DRB, actuate the O2 Heater Test.
Monitor O2 voltage for up to two minutes.
Is the O2 Sensor voltage still between .4 and .6 volts?All
Ye s®Go To 4
No®Go To 3
3 At this time the 1/1 O2S HEATER FAILURE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the 1/1 O2S HEATER FAILURE reoccur?All
Ye s®Go To 4
No®1/1 O2S Heater failure no longer exists.
Perform VERIFICATION TEST VER-5A3.
62
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0137 1/2 O2 SENSOR VOLTAGE SHORTED TO GROUND
When Monitored and Set Condition:
P-0137 1/2 O2 SENSOR VOLTAGE SHORTED TO GROUND
When Monitored: With the ignition key off, after the O2 Sensor cools down; and after the
next key on provided that it is a cold start (coolant temperature less than 38 degrees C
(100.4 degrees F) and ambient temperature within 13.7 degrees C (7.2 degrees F) of coolant
temperature.
Set Condition: The Downstream O2 Sensor Signal voltage is below 0.156 volt prior to O2
Sensor Heater test (cool down period), and O2 voltage less than 0.156 volt after the key on
in the subsequent start.
POSSIBLE CAUSES
1/2 02 SENSOR VOLTAGE LOW
1/2 O2S SIGNAL CIRCUIT SHORT TO GROUND
1/2 O2S SIGNAL CKT SHORT TO GROUND CIRCUIT
1/2 O2 SENSOR DEFECTIVE
PCM DEFECTIVE (1/2 O2S)
TEST ACTION APPLICABILITY
1 Ignition Off
Turn ignition on.
With the DRB, monitor the Downstream O2 Sensor voltage for a few minutes.
Wait three minutes or until the voltage stabilizes (between 0.4 and 0.6 volt).
With the DRB, monitor the Downstream O2 Sensor voltage.
Is the Downstream O2 Sensor voltage below 0.156 volt?All
Ye s®Go To 2
No®The condition required to set this trouble code is not present at
this time.
Perform Powertrain Verification Test VER-5A.
2 Ignition Off
Disconnect the Downstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Key on.
With the DRB, monitor the Downstream O2 Sensor voltage.
Is the Downstream O2 Sensor voltage below 0.156 volts?All
Ye s®Go To 3
No®Replace the Downstream O2 Sensor.
Perform Powertrain Verification Test VER-5A.
64
DRIVEABILITY
ProCarManuals.com

Symptom:
P-0141 1/2 O2S HEATER FAILURE
When Monitored and Set Condition:
P-0141 1/2 O2S HEATER FAILURE
When Monitored: With the ignition key off, after the engine cools down.
Set Condition: No sensor output signal is received when the PCM powers up the sensor
heater.
POSSIBLE CAUSES
1/2 O2 SENSOR CONNECTOR DAMAGED
1/2 O2 SENSOR GND CIRCUIT OPEN
ASD RELAY OUTPUT CIRCUIT OPEN
1/2 O2 SENSOR FAILURE
1/2 O2 SENSOR HEATER ELEMENT FAILURE
1/2 O2S HEATER FAILURE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the GLOBAL GOOD TRIP counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 3
2 Turn Ignition On (Engine Off), wait three minutes.
With the DRB, monitor the O2 Sensor voltage for a few minutes until the voltage
stabilizes between .4 and .6 volts.
With the DRB, actuate the O2 Heater test.
Monitor O2 voltage for up to two minutes.
Is the O2 Sensor voltage still between .4 and .6 volts?All
Ye s®Go To 3
No®Go To 4
3 At this time the 1/2 O2S HEATER FAILURE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the 1/2 O2S HEATER FAILURE reoccur?All
Ye s®Go To 4
No®1/2 O2S Heater failure no longer exists.
Perform VERIFICATION TEST VER-5A3.
73
DRIVEABILITY
ProCarManuals.com

Symptom:start here
P-0201 INJECTOR #1 CONTROL CIRCUIT
When Monitored and Set Condition:
P-0201 INJECTOR #1 CONTROL CIRCUIT
When Monitored: With battery voltage greater than 12 volts, the auto shutdown relay
energized, injector pulse width less than 10ms, and engine speed less than 3000 rpm.
Set Condition: This trouble code takes .64 to 10.0 seconds to set when no inductive kick
is sensed .18ms after injector turn off, and with no other injectors on.
POSSIBLE CAUSES
ASD RELAY OUTPUT CIRCUIT OPEN
INJECTOR DEFECTIVE
INJECTOR #1 DRIVER CIRCUIT OPEN
INJECTOR #1 DRIVER CIRCUIT SHORTED TO GROUND
POWERTRAIN CONTROL MODULE DEFECTIVE
INJECTOR #1 DRIVER CIRCUIT SHORT TO GROUND
INJECTOR #1 DRIVER CIRCUIT SHORT TO GROUND (PCM)
TEST ACTION APPLICABILITY
1 Ignition Off
Start engine, let idle for at least 20 seconds.
Key on, engine off.
With the DRB, read Trouble Codes.
Is the Global Good Trip counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 7
2 Ignition Off
Disconnect the Injector #1 Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure resistance of Injector #1.
Is the resistance between 10.0 and 16.0 ohms?All
Ye s®Go To 3
No®Replace the Fuel Injector.
Perform Powertrain Verification Test VER-5A.
83
DRIVEABILITY
ProCarManuals.com