service CHRYSLER VOYAGER 2000 Diagnostic Manual

TEST ACTION APPLICABILITY
8 Ignition On, Engine Not Running.
With the DRB, read codes.
With the DRB, actuate the Evap Purge Solenoid.
Wiggle Wiring Harness from the Solenoid to PCM.
Does the Evap Purge Solenoid Control Circuit code return?ALL
Ye s®Repair as necessary where wiggling caused problem to appear.
Perform Powertrain Verification Test VER-5A.
No®Go To 9
9 Ignition Off.
Using the Schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?ALL
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 10
10 Check the freeze frame data to determine the conditions when code was set.
Attempt duplication of 'freeze frame' conditions for added diagnostics.
If there are no other possible causes remaining there is assumed to be an9intermit-
tent9problem with a Wiring Harness Connector or Wire.
View repair options.ALL
Repair
Visually inspect related Wire Harness Connectors and Harnesses.
Look for broken, bent, pushed out, or corroded terminals and for
chafed, pierced, or partiallly broken wire, respectively. Refer to
any hotlines or technical service bulletins that apply.
11 Ignition On, Engine Not Running.
With the DRB, actuate the Evap Purge Solenoid.
With the DRB, read codes.
Is the Global Good Trip displayed and equal to 0?ALL
Ye s®Go To 12
No®Go To 18
12 Ignition Off.
Disconnect Proportional Purge Solenoid Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance of the Proportional Purge Solenoid.
Is the resistance 14.2 ohms +/- 1.4?ALL
Ye s®Go To 13
No®Replace the open Proportional Purge Solenoid.
Perform Powertrain Verification Test VER-5A.
145
DRIVEABILITY
P-0443 EVAP PURGE SOLENOID CIRCUIT ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
16 Ignition Off.
Disconnect Proportional Purge Solenoid Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the battery.
Note: Check connectors - Clean/repair as necessary.
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Using and Ohmmeter, measure the PWM Purge Sense Circuit PCM to Solenoid
Connector.
Is the resistance below 5.0 ohms?ALL
Ye s®Go To 17
No®Repair the open PWM Purge Sense Circuit.
Perform Powertrain Verification Test VER-5A.
17 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.ALL
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-5A.
18 Ignition On, Engine Not Running.
With the DRB, actuate the Evap Purge Solenoid.
With the DRB, read codes.
Wiggle Wiring Harness from the Solenoid to PCM.
Does the Evap Purge Solenoid Control Circuit code return?ALL
Ye s®Repair as necessary where wiggling caused problem to appear.
Perform Powertrain Verification Test VER-5A.
No®Go To 19
19 Ignition Off.
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?ALL
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 20
20 Check the freeze frame data to determine the conditions when code was set.
Attempt duplication of 'freeze frame' conditions for added diagnostics.
If there are no other possible causes remaining there is assumed to be an9intermit-
tent9problem with a Wiring Harness Connector or Wire.
View repair options.ALL
Repair
Visually inspect related Wire Harness Connectors and Harnesses.
Look for broken, bent, pushed out, or corroded terminals and for
chafed, pierced, or partiallly broken wire, respectively. Refer to
any hotlines or technical service bulletins that apply.
147
DRIVEABILITY
P-0443 EVAP PURGE SOLENOID CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
P-1281 ENGINE IS COLD TOO LONG
When Monitored and Set Condition:
P-1281 ENGINE IS COLD TOO LONG
When Monitored: Ignition key on, engine not running. Ambient temperature greater
than þ11ÉC (-11ÉF) and coolant temperature greater than þ7ÉC (19ÉF)
Set Condition: The engine does not warm to 79 degrees C (176 degrees F) while driving
for 20 minutes after start.
POSSIBLE CAUSES
ENGINE COLD TOO LONG
TEST ACTION APPLICABILITY
1 Start Engine
Drive vehicle under normal driving conditions for 20 minutes.
With the DRB, read Engine Coolant Temperature.
Did the engine warm to 79 degrees C (176 degrees F)?All
Ye s®Test Complete.
No®See pertinent service manual information for cooling system
diagnostics.
177
DRIVEABILITY
ProCarManuals.com

Symptom:
P-1294 TARGET IDLE NOT REACHED
When Monitored and Set Condition:
P-1294 TARGET IDLE NOT REACHED
When Monitored: Engine idling more than 2.8 seconds and coolant temp greater than 70
degrees C (160 degrees F). For an automatic transmission, in drive mode. There must not
be a MAP Sensor or TP Sensor or speed sensor trouble code.
Set Condition: Engine idle is > 200 RPM above target idle speed or less than 100 RPM
below target idle speed for 20 seconds. Two consecutive failures in a row will store this
trouble code.
POSSIBLE CAUSES
ENG VACUUM HOSES AND COMPONENTS LEAKS
THROTTLE BODY DEFECTIVE
THROTTLE PLATE/LINKAGE NOT IN CORRECT POS
IAC WIRING HARNESS INTERMITTENT DEFECT
IAC WIRING HARNESS OBSERVABLE DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Does the engine exhibit a start and stall condition?All
Ye s®Go To 2
No®Go To 4
2 Ignition Off
Perform minimum air flow test that is described in the service information.
Is the idle RPM within the range shown in the chart?All
Ye s®Test Complete.
No®Go To 3
180
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition off.
Remove the Throttle Body per service information procedure.
Note: Clean Throttle Body in a well ventilated area and wear rubber gloves.
While holding the Throttle open spray entire Throttle Body Bore with Mopar parts
cleaner.
Using a soft scuff pad, clean the Throttle Body Bore and Throttle Plate.
Using compressed air, dry the Throttle Body and install Throttle Body on Manifold.
Reconnect IAC Motor Connector and reset the IAC Motor Steps with the DRB.
Start engine and let idle.
With the DRB, actuate the minimum air flow.
Is the idle RPM within the range shown in the chart? Refer to the Service
Information.All
Ye s®Test Complete.
No®Replace the Throttle Body.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Start engine, allow engine idle to stabilize for 60 seconds.
With the DRB, read target idle and engine RPM.
Is the engine RPM within +200/-100 RPM of target idle?All
Ye s®Go To 5
No®Go To 8
5 Ignition Off
Remove the IAC Motor from the housing.
Turn Ignition on with Engine Not Running.
With the DRB, actuate the IAC Stepper Motor.
Wiggle the Wiring Harness from the IAC Motor to the PCM.
Did the IAC stop operating at any time?All
Ye s®Repair the Harness or Connectors as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 7
7 Ignition On, Engine Not Running
Check Throttle Plate and Linkage for a binding condition.
The Throttle Linkage must be free and the Throttle Plate at the idle
position.
Ensure Throttle Plate is fully closed and against its stop.
Is the Throttle Plate and Linkage okay?All
Ye s®Test Complete.
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
181
DRIVEABILITY
P-1294 TARGET IDLE NOT REACHED ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
2 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 3
3 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out, or miswired?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 4
4 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove the Camshaft Position Sensor.
Inspect the Camshaft Sprocket. See pertinent service information for instructions.
Is the Camshaft Sprocket okay?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Go To 5
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
5 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove the CMP Sensor.
Inspect the Camshaft Thrust Plate(s).
Are the Camshaft Thrust Plate(s) attached?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Replace the Camshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
No®Repair or replace the Camshaft Thrust Plate(s) as necessary.
Perform Powertrain Verification Test VER-5A.
6 Start Engine.
At PCM, backprobe CMP Sensor Signal Circuit with Oscilloscope's voltage measure-
ment lead.
While observing the Oscilloscope pattern, wiggle CMP Sensor Circuit from Sensor to
PCM.
Were any signals missing when the wiggle test was conducted?ENGINE - 3.3L V6
and/or ENGINE -
3.8L V6 and/or EN-
GINE - 3.3L V6
FFV
Ye s®Note where wiggling the Wires caused a missing CMP Sensor
Signal. Repair Camshaft and Crankshaft Wiring Harness as
necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 7
192
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
22 Ignition Off.
At the CMP Sensor, backprobe the CMP Sensor Signal Circuit with the Oscilloscope
voltage measurement lead.
Start the Engine and observe the CMP Sensor voltage pattern on the Oscilloscope.
Are there any of the Camshaft Position Sensor Signals missing?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Go To 23
No®Go To 27
23 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out or miswired?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 24
24 Ignition Off.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Inspect all Terminals.
Is any Terminal damaged, pushed out, or miswired?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Repair Terminal(s) for damage, pushout or miswiring.
Perform Powertrain Verification Test VER-5A.
No®Go To 25
25 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove & inspect the CMP Sensor & Target Magnet for damage or misalignment.
Is the Camshaft Target Magnet okay?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Go To 26
No®Repair or replace Camshaft Target Magnet as necessary.
Perform Powertrain Verification Test VER-5A.
26 Ignition Off.
Disconnect the CMP Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Remove and inspect the CMP Sensor and Target Magnet for damage or mis-
alignment.
Check Camshaft endplay per pertinent service information.
Is the Camshaft endplay within specs?ENGINE - 2.0L
and 2.4L I-4
DOHC
Ye s®Replace the Camshaft Position Sensor.
Perform Powertrain Verification Test VER-5A.
No®Repair or replace Camshaft/Cylinder Head as necessary.
Perform Verification Test VER-5A.
196
DRIVEABILITY
P-1391 INTERMITTENT LOSS OF CMP OR CKP ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Check the freeze frame data to determine the conditions when code was set.
Attempt duplication of 'freeze frame' conditions for added diagnostics.
If there are no other possible causes remaining there is assumed to be an9intermit-
tent9problem with a Wiring Harness Connector or Wire.
View repair options.All
Repair
Visually inspect related Wire Harness Connectors and Harnesses.
Look for broken, bent, pushed out, or corroded terminals and for
chafed, pierced, or partiallly broken wire, respectively. Refer to
any hotlines or technical service bulletins that apply.
5 Ignition Off
Disconnect the LDP Solenoid.
Note: Check connectors - Clean/repair as necessary.
Key on.
Using a Voltmeter, measure the voltage of the Fused Ignition Switch Output Circuit
at the Solenoid Connector.
Is the voltage above 10.0 volts?All
Ye s®Go To 6
No®Repair the open Fused Ignition Switch Output Circuit.
Perform Powertrain Verification Test VER-6A.
6 Ignition Off
Disconnect the LDP Solenoid.
Note: Check connectors - Clean/repair as necessary.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance of the LDP Solenoid Control Circuit at
the PCM Connector to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the LDP Solenoid Circuit for a short to ground.
Perform Powertrain Verification Test VER-6A.
No®Go To 7
7 Ignition Off
Disconnect the LDP Solenoid.
Note: Check connectors - Clean/repair as necessary.
Disconnect the PCM.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the resistance of the LDP Solenoid Control Circuit from
the PCM Connector to the LDP Connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 8
No®Repair the open LDP Solenoid Control Circuit.
Perform Powertrain Verification Test VER-6A.
210
DRIVEABILITY
P-1495 LEAK DETECTION PUMP SOLENOID CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
* CHECKING MINIMUM IDLE AIR FLOW
POSSIBLE CAUSES
MINIMUM AIR FLOW IS WITHIN ACCEPTABLE RANGE
THROTTLE BODY DEFECTIVE (MIN AIR FLOW OUT OF RANGE)
TEST ACTION APPLICABILITY
1 Start the engine and allow it to reach operating temperature.
Perform the Minimum Air Flow test as described in service information.
Is idle RPM within the range shown in the chart?All
Ye s®Throttle Body minimum air flow is set correctly.
No®Go To 2
2 Ignition Off
Remove Throttle Body per service information.
Note: Clean Throttle Body in a well ventilated area and wear rubber gloves.
While holding the Throttle open, spray entire Throttle Body Bore with Mopar parts
cleaner.
Using a soft scuff pad, clean the Throttle Body Bore and Throttle Plate.
Using compressed air, dry the Throttle Body and install Throttle Body on manifold.
Start the engine and allow it to reach operating temperature.
With the DRB, enter System Test and perform the Minimum Air Flow Test.
Is the idle RPM within the range shown in the chart?All
Ye s®Test Complete.
No®Replace Throttle Body.
Perform Verification Test VER-2A.
246
DRIVEABILITY
ProCarManuals.com

Symptom:
* CHECKING THE ENGINE MECHANICAL SYSTEMS
POSSIBLE CAUSES
CHECKING ENGINE MECHANICAL SYSTEMS
TEST ACTION APPLICABILITY
1 At this point in the diagnostic test procedure, you have determined that all of the
engine electrical systems are operating as designed; therefore, they are not the cause
of the driveability problem.
The following additional items should be checked as possible mechanical causes of
the problem:
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
CAMSHAFT LOBES - check for abnormal wear
CRANK SENSOR PICK-UP - check crankshaft slots for debris/deterioration
ENGINE EXHAUST SYSTEM - must be free of any restrictions
ENGINE PCV SYSTEM - must flow freely
ENGINE DRIVE SPROCKETS - must be properly positioned
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to
correct injector
Note: If you came to this test from the oxygen sensor, and the rich or lean
condition is not caused by one of the first items above, replace the power-
train control module and perform TEST VER-2A (Road Test Verification).
Always look for any Technical Service Bulletins that may relate to the problem.
Did you come from an Oxygen Sensor rich or lean condition test?All
Ye s®Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-2A.
No®Test Complete.
253
DRIVEABILITY
ProCarManuals.com