radio CHRYSLER VOYAGER 2004 Manual PDF

(4) Install andlightly tightenthe three remain-
ing wheel mounting nuts, securing the wheel cover in
place (Fig. 12).
(5) Progressively tighten all five wheel mounting
nuts in the proper sequence (Fig. 16). Tighten wheel
nuts to a torque of 135 N´m (100 ft. lbs.).
(6) Lower the vehicle.
TIRE PRESSURE MONITORING
DESCRIPTION
Some versions of this vehicle are equipped with a
Tire Pressure Monitoring (TPM) system. It monitors
air pressure in the four road tires (excludes spare).
Pressure in the spare tire is not monitored.
There is a sensor (transmitter) in each of the vehi-
cle's four road wheels. The system alerts the driver
when tire pressure falls outside predetermined
thresholds (pressure too low or too high). A message
is then displayed on the Electronic Vehicle Informa-
tion Center (EVIC) located in the overhead console.
For further information, refer to the Owners Man-
ual or the appropriate diagnostic information.
OPERATION
The Tire Pressure Monitoring (TPM) system uses
radio and sensor technology to monitor tire air pres-
sure levels. Sensors, mounted to each road wheel as
part of the valve stem, transmit tire pressure read-
ings to a receiver located in the overhead console.
These transmissions occur once every minute at
speeds over 20 mph (32 km/h). The Tire Pressure
Monitoring system remains active even if no tire
pressure related message is displayed in the EVIC.
If any road tire pressure has exceeded the low or
high pressure threshold (refer to chart below), the
TPM system will display a message in the EVIC and
sound a chime. This message will be displayed for
the rest of the ignition cycle, or until either the Low/
High Tire pressure condition has been corrected. If
the C/T, MENU, STEP or RESET button is pressed,
the message is replaced by the new message
requested; however, if the Low/High Tire condition
has not been corrected, the Low/High Tire pressure
message will again be displayed.
Fig. 14 TWO WHEEL MOUNTING NUTS INSTALLED
1 - WHEEL
2 - VALVE STEM
3 - HUB PILOT
4 - NUTS
Fig. 15 WHEEL COVER INSTALLATION OVER TWO
NUTS
1 - RETAINING TABS
2 - VALVE STEM
3 - BOLT-ON WHEEL COVER
Fig. 16 NUT TIGHTENING SEQUENCE
RSTIRES/WHEELS22-9
TIRES/WHEELS (Continued)

TIRES/WHEELS
TABLE OF CONTENTS
page page
TIRE PRESSURE MONITORING............... 1TIRES................................... 5
TIRE PRESSURE MONITORING
TABLE OF CONTENTS
page page
TIRE PRESSURE MONITORING DESCRIPTION ..........................1
OPERATION ............................1
SENSOR - TPM DESCRIPTION ..........................1
OPERATION ............................2
CAUTION ..............................2 DIAGNOSIS AND TESTING - TIRE PRESSURE
SENSOR .............................2
STANDARD PROCEDURE - TIRE PRESSURE SENSOR RETRAIN .....................2
REMOVAL .............................2
INSTALLATION ..........................3
TIRE PRESSURE MONITORING
DESCRIPTION
Some versions of this vehicle are equipped with a
Tire Pressure Monitoring (TPM) system. It monitors
air pressure in the four road tires. Pressure in the
spare tire is not monitored. There is a sensor (transmitter) in each of the vehi-
cle's four road wheels that is built in to the valve
stem. The system alerts the driver when tire pres-
sure falls outside predetermined thresholds (pressure
too low or too high). A message is then displayed on
the Compass Mini Trip Computer (CMTC). For further information, refer to the Owners Man-
ual or the appropriate diagnostic information.
OPERATION
The Tire Pressure Monitoring (TPM) system uses
radio and sensor technology to monitor tire air pres-
sure levels. Sensors, mounted to each road wheel as
part of the valve stem, transmit an RF frequency
indicating their individual pressure to a receiver
located in the Sentry Key Remote Entry Module
(SKREEM). These transmissions occur approximately
once every minute at speeds over 13 mph (20 km/h).
The Tire Pressure Monitoring system remains active
even if no tire pressure related message is displayed.
SENSOR - TPM
DESCRIPTION
On vehicles equipped with Tire Pressure Monitor-
ing, one tire pressure sensor is mounted to each
wheel (Fig. 2). Each sensor has an internal battery
that lasts up to 10 years. The battery is not service-
able. At the time of battery failure, the sensor must
be replaced. The serviceable components of the tire
pressure sensor are: ² Sensor-To-Wheel Grommet
² Valve Stem Cap
² Valve Stem Core
Valve stem caps and cores are specifically designed
for the tire pressure monitoring sensors. Although
similar to standard valve stem caps and cores, they
are different.
CAUTION: Do not use a standard valve stem cap or
core in a tire pressure sensor. Always use the orig-
inal equipment style sensor cap and core.
CAUTION: Do not reuse the Sensor-To Wheel Grom-
met. Always use a new grommet when installing a
pressure sensor and properly torque the sensor
nut.
RS TIRES/WHEELS22s-1

INSTRUMENT PANEL TOP PAD
ASSEMBLY
REMOVAL
(1) Remove the instrument cluster (Fig. 14). (Refer
to 8 - ELECTRICAL/INSTRUMENT CLUSTER -
REMOVAL)
(2) Remove the message center (Fig. 14). (Refer to
8 - ELECTRICAL/MESSAGE CENTER - REMOVAL)
(3) Remove the radio (Fig. 14). (Refer to 8 - ELEC-
TRICAL/AUDIO/RADIO - REMOVAL)
(4) Remove the headlamp switch (Fig. 14). (Refer
to 8 - ELECTRICAL/LAMPS/LIGHTING - EXTERI-
OR/HEADLAMP SWITCH - REMOVAL)
(5) Remove the lower console (Fig. 14). (Refer to 23
- BODY/INSTRUMENT PANEL/LOWER CONSOLE
- REMOVAL)
(6) Remove the lower panel. (Refer to 23 - BODY/
INSTRUMENT PANEL/LOWER INSTRUMENT
PANEL TRIM - REMOVAL)
(7) Remove the instrument panel assembly. (Refer
to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL ASSEMBLY - REMOVAL)
(8) Remove the instrument panel speakers.
(9) Remove the glove box light.
(10) Remove the two passenger air bag mounting
bolts (Fig. 15).
(11) Loosen the three passenger air bag support
bracket bolts to the hydro-form rail (Fig. 15).
(12) Remove the 16 screws along the upper edge of
the pad & panel assembly.
(13) Remove the 19 screws along the lower edge of
the pad & panel assembly.
(14) Remove the pad and panel assembly (Fig. 14).
Fig. 13 OVER STEERING COLUMN COVER
1 - INSTRUMENT PANEL OVER STEERING COLUMN COVER
2 - INSTRUMENT PANEL
Fig. 14 INSTRUMENT PANEL ASSEMBLY
1 - INSTRUMENT CLUSTER
2 - MESSAGE CENTER
3 - TOP COVER
4 - PAD AND PANEL ASSEMBLY
5 - LOWER CONSOLE
6 - LOWER PANEL
7 - RADIO
8 - HEADLAMP SWITCH
Fig. 15 AIRBAG MOUNTING HARDWARE
1 - AIR BAG SCREWS (2)
2 - ELECTRICAL CONNECTOR
3 - AIR BAG SUPPORT BRACKET BOLTS (3)
4 - HYDRO-FORM INSTRUMENT PANEL SUPPORT RAIL
RSINSTRUMENT PANEL23-71
OVER STEERING COLUMN COVER (Continued)

INSTALLATION
(1) Position the pad & panel assembly onto the
instrument panel support structure.
(2) Install the 19 screws along the lower edge of
the pad & panel assembly.
(3) Install the 16 screws along the upper edge of
the pad & panel assembly.
(4) Install and tighten the two passenger air bag
mounting screws.
(5) Tighten the three passenger air bag support
bracket bolts to the hydro-form tube.
(6) Install the glove box light.
(7) Install the instrument panel speakers.
(8) Install the instrument panel assembly. (Refer
to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL ASSEMBLY - INSTALLATION)
(9) Install the lower panel. (Refer to 23 - BODY/
INSTRUMENT PANEL/LOWER INSTRUMENT
PANEL TRIM - INSTALLATION)(10) Install the lower console. (Refer to 23 - BODY/
INSTRUMENT PANEL/LOWER CONSOLE -
INSTALLATION)
(11) Install the headlamp switch. (Refer to 8 -
ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/
HEADLAMP SWITCH - INSTALLATION)
(12) Install the radio. (Refer to 8 - ELECTRICAL/
AUDIO/RADIO - INSTALLATION)
(13) Install the message center. (Refer to 8 -
ELECTRICAL/MESSAGE CENTER - INSTALLA-
TION)
(14) Install the instrument cluster. (Refer to 8 -
ELECTRICAL/INSTRUMENT CLUSTER - INSTAL-
LATION)
23 - 72 INSTRUMENT PANELRS
INSTRUMENT PANEL TOP PAD ASSEMBLY (Continued)

MOUNTING STUDS - FRONT -
INSTALLATION, WHEEL................22-21
MOUNTING STUDS - FRONT - REMOVAL,
WHEEL............................22-20
MOUNTING STUDS - REAR -
INSTALLATION, WHEEL................22-22
MOUNTING STUDS - REAR - REMOVAL,
WHEEL............................22-21
MOUNTS - FRONT - INSTALLATION,
SPRING.............................2-44
MOUNTS - FRONT - REMOVAL, SPRING . . . 2-43
MOUNTS - REAR - INSTALLATION,
SPRING.............................2-45
MOUNTS - REAR - REMOVAL, SPRING....2-44
MUFFLER - INSTALLATION..............11-7
MUFFLER - REMOVAL..................11-7
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-18
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-18
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-18
NAME PLATES - ADHESIVE ATTACHED -
INSTALLATION, EXTERIOR.............23-51
NAME PLATES - ADHESIVE ATTACHED -
REMOVAL, EXTERIOR.................23-51
NAME PLATES - TAPE ATTACHED -
INSTALLATION, EXTERIOR.............23-51
NAME PLATES - TAPE ATTACHED -
REMOVAL, EXTERIOR.................23-51
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-13
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-13
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP TO FILLER..............7-27
NGC CONTROLLER - REMOVAL.........8E-17
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-47
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-47
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-47
NO CUPHOLDER - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD............23-97
NO CUPHOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE SHIELD............23-97
NOISE - DIAGNOSIS AND TESTING,
EXCESSIVE EXHAUST SYSTEM...........11-2
NOISE - DIAGNOSIS AND TESTING,
REAR DRIVELINE MODULE..............3-24
NOISE - DIAGNOSIS AND TESTING, TIRE . 22-14,
22s-6
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-74
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, HYDRAULIC LASH
ADJUSTER...........................9-34
NOISE SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO.................8A-11
NOISE SUPPRESSION COMPONENTS -
OPERATION, RADIO..................8A-12
NON-ABS JUNCTION BLOCK -
DESCRIPTION...................5-33,5s-32
NON-ABS JUNCTION BLOCK -
INSTALLATION
...................5-33,5s-32
NON-ABS JUNCTION BLOCK -
OPERATION
.....................5-33,5s-32
NON-ABS JUNCTION BLOCK - REMOVAL
. . 5-33,
5s-32
NON-MONITORED CIRCUITS -
OPERATION
..........................25-5
NOT FILL - DIAGNOSIS AND TESTING,
VEHICLE DOES
......................25-16
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION
....................Intro.-9
NVLD - INSTALLATION, WITH
...........25-20
NVLD - REMOVAL, WITH
..............25-19
O2 SENSOR - DESCRIPTION
............14-32
O2 SENSOR - OPERATION
.............14-32
OBTAINING DIAGNOSTIC TROUBLE
CODES - STANDARD PROCEDURE
.......8E-15
OCCUPANT RESTRAINT CONTROLLER -
DESCRIPTION
........................8O-8
OCCUPANT RESTRAINT CONTROLLER -
INSTALLATION
.......................8O-8OCCUPANT RESTRAINT CONTROLLER -
OPERATION..........................8O-8
OCCUPANT RESTRAINT CONTROLLER -
REMOVAL...........................8O-8
OIL - DESCRIPTION, FLEXIBLE FUEL
ENGINE..............................0-3
OIL - DESCRIPTION, REFRIGERANT......24-92
OIL - DIESEL ENGINES - DESCRIPTION,
ENGINE..............................0-6
OIL - OPERATION, REFRIGERANT........24-92
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE.............9-137,9-53
OIL AND LUBRICANTS - DESCRIPTION,
ENGINE..............................0-1
OIL COOLER - DESCRIPTION,
TRANSMISSION.......................7-37
OIL COOLER - INSPECTION,
TRANSMISSION.......................7-37
OIL COOLER - INSTALLATION,
TRANSMISSION.......................7-37
OIL COOLER & LINES - DESCRIPTION....9-138
OIL COOLER & LINES - INSTALLATION . . . 9-138
OIL COOLER & LINES - OPERATION......9-138
OIL COOLER & LINES - REMOVAL.......9-138
OIL COOLER - REMOVAL,
TRANSMISSION.......................7-37
OIL COOLER LINES - INSTALLATION,
TRANSMISSION.......................7-38
OIL COOLER LINES - REMOVAL,
TRANSMISSION.......................7-38
OIL FILTER - DESCRIPTION.............9-53
OIL FILTER - INSTALLATION........9-139,9-53
OIL FILTER - REMOVAL............9-139,9-53
OIL FILTER ADAPTER - INSTALLATION....9-139
OIL FILTER ADAPTER - REMOVAL.......9-139
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE.........9-10,9-86
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..............9-8,9-82
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-93
OIL LEVEL CHECK - STANDARD
PROCEDURE, ENGINE.................9-137
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-53
OIL PAN - CLEANING.................9-140
OIL PAN - INSPECTION................9-140
OIL PAN - INSTALLATION..........9-140,9-54
OIL PAN - REMOVAL..............9-140,9-54
OIL PRESSURE - DIAGNOSIS AND
TESTING, CHECKING ENGINE............9-52
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE....................9-136
OIL PRESSURE RELIEF VALVE -
INSTALLATION.......................9-141
OIL PRESSURE RELIEF VALVE -
REMOVAL..........................9-141
OIL PRESSURE SWITCH - DESCRIPTION . . 9-141
OIL PRESSURE SWITCH - INSTALLATION . 9-141,
9-54
OIL PRESSURE SWITCH - OPERATION....9-141
OIL PRESSURE SWITCH - REMOVAL . 9-141,9-54
OIL PUMP - ASSEMBLY...........9-143,9-56
OIL PUMP - ASSEMBLY.......21-232,21s-132
OIL PUMP - CLEANING............9-142,9-56
OIL PUMP - DESCRIPTION.............9-142
OIL PUMP - DESCRIPTION.....21-230,21s-131
OIL PUMP - DISASSEMBLY........9-142,9-55
OIL PUMP - DISASSEMBLY.....21-230,21s-131
OIL PUMP - INSPECTION..........9-142,9-56
OIL PUMP - INSTALLATION........9-144,9-57
OIL PUMP - INSTALLATION, SEAL......21-233,
21s-133
OIL PUMP - OPERATION.......21-230,21s-131
OIL PUMP - REMOVAL............9-142,9-55
OIL PUMP - REMOVAL, SEAL . . . 21-232,21s-133
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT...................9-127,9-40
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT
...................9-127,9-40
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT
...................9-129,9-42
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT
...................9-128,9-41
OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR
..................9-129
OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR
..................9-129OIL SEAL(S) - INSTALLATION,
CAMSHAFT..........................9-28
OIL SEAL(S) - REMOVAL, CAMSHAFT.....9-27
ON-BOARD DIAGNOSTIC SYSTEM -
DIAGNOSIS AND TESTING..............8F-21
OPEN LATCH - INSTALLATION, HOLD.....23-25
OPEN LATCH - REMOVAL, HOLD........23-25
OPEN LATCH CABLE - INSTALLATION,
HOLD..............................23-38
OPEN LATCH CABLE - REMOVAL, HOLD . . . 23-38
OPEN LATCH STRIKER - INSTALLATION,
HOLD..............................23-26
OPEN LATCH STRIKER - REMOVAL,
HOLD..............................23-26
OPEN SWITCH - DESCRIPTION, FULL....8N-12,
8N-31
OPEN SWITCH - INSTALLATION, FULL....8N-13
OPEN SWITCH - OPERATION, FULL . 8N-12,8N-31
OPEN SWITCH - REMOVAL, FULL.......8N-13
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-13
OPENING DIMENSIONS -
SPECIFICATIONS, BODY..............23-127
OPENING REINFORCEMENT -
INSTALLATION, GRILLE................23-54
OPENING REINFORCEMENT - REMOVAL,
GRILLE............................23-54
ORDER, SPECIFICATIONS - FIRING........8I-3
O-RING - INSTALLATION, REAR COVER . . . 21-20
O-RING - REMOVAL, REAR COVER.......21-19
ORVR - OPERATION..................25-14
OUTBOARD - FRONT - INSTALLATION,
SEAT BELT & RETRACTOR.............8O-14
OUTBOARD - FRONT - REMOVAL, SEAT
BELT & RETRACTOR..................8O-14
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - FIRST ROW...........8O-14
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - SECOND ROW - LEFT . . . 8O-17
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - SECOND ROW -
RIGHT.............................8O-15
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - FIRST ROW.............8O-14
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - LEFT.....8O-17
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT....8O-15
OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT....8O-16
OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT & RETRACTOR -
SECOND ROW - RIGHT................8O-16
OUTER - INSTALLATION, CV BOOT........3-10
OUTER - REMOVAL, CV BOOT...........3-10
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-113
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-113
OUTER HALF SHAFT SEAL -
INSTALLATION.......................21-19
OUTER HALF SHAFT SEAL - REMOVAL . . . 21-19
OUTER TIE ROD - INSTALLATION........19-34
OUTER TIE ROD - REMOVAL...........19-34
OUTLET - DESCRIPTION, POWER......8W-97-4
OUTLET - DIAGNOSIS & TESTING,
POWER..........................8W-97-4
OUTLET - INSTALLATION, DEMISTER
.....24-46
OUTLET - INSTALLATION, INSTRUMENT
PANEL
.............................24-46
OUTLET - OPERATION, POWER
.......8W-97-4
OUTLET - REMOVAL, DEMISTER
........24-45
OUTLET - REMOVAL, INSTRUMENT
PANEL
.............................24-45
OUTLETS - DESCRIPTION, AIR
.....24-44,24-56
OUTLETS - INSTALLATION, AIR
.........24-56
OUTLETS - INSTALLATION, CENTER
BEZEL
.............................24-45
OUTLETS - REMOVAL, AIR
.............24-56
OUTLETS - REMOVAL, CENTER BEZEL
....24-44
OUTPUT - DESCRIPTION, SPEED
SENSOR
....................21-241,21s-142
OUTPUT - INSTALLATION, SPEED
SENSOR
....................21-242,21s-143
OUTPUT - OPERATION, 5 VOLT SUPPLY -
PCM
...............................8E-15
RSINDEX23
Description Group-Page Description Group-Page Description Group-Page

QUAD CHILD SEAT - REMOVAL.........23-89
QUARTER GLASS INTEGRAL ANTENNA -
EXPORT - DESCRIPTION................8A-9
QUARTER GLASS INTEGRAL ANTENNA -
EXPORT - DIAGNOSIS AND TESTING......8A-9
QUARTER GLASS INTEGRAL ANTENNA -
EXPORT - OPERATION.................8A-9
QUARTER PANEL/FENDER AIR
EXHAUSTER - DESCRIPTION, REAR......23-57
QUARTER PANEL/FENDER AIR
EXHAUSTER - INSTALLATION, REAR.....23-58
QUARTER PANEL/FENDER AIR
EXHAUSTER - REMOVAL, REAR.........23-57
QUARTER TRIM BOLSTER -
INSTALLATION.......................23-79
QUARTER TRIM BOLSTER - REMOVAL....23-79
QUARTER TRIM PANEL - INSTALLATION,
LEFT..............................23-80
QUARTER TRIM PANEL - INSTALLATION,
RIGHT.............................23-79
QUARTER TRIM PANEL - REMOVAL,
LEFT..............................23-80
QUARTER TRIM PANEL - REMOVAL,
RIGHT.............................23-79
QUARTER WINDOW - INSTALLATION....23-111
QUARTER WINDOW - REMOVAL........23-111
QUICK LEARN PROCEDURE - STANDARD
PROCEDURE...................8E-16,8E-23
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE........................14-14
RACK - DESCRIPTION, LOWER DRIVE
UNIT TRACK........................8N-34
RACK - INSTALLATION, LOWER DRIVE
UNIT TRACK........................8N-34
RACK - OPERATION, LOWER DRIVE UNIT
TRACK.............................8N-34
RACK - REMOVAL, LOWER DRIVE UNIT
TRACK.............................8N-34
RACK CROSSBAR - INSTALLATION,
LUGGAGE..........................23-57
RACK CROSSBAR - REMOVAL, LUGGAGE . 23-56
RACK RISER - INSTALLATION, LUGGAGE . . 23-56
RACK RISER - REMOVAL, LUGGAGE.....23-55
RADIAL-PLY TIRES - DESCRIPTION . 22-14,22s-6
RADIATOR - INSTALLATION.............7-25
RADIATOR - REMOVAL.................7-25
RADIATOR CAP TO FILLER NECK SEAL -
DIAGNOSIS AND TESTING..............7-27
RADIATOR DRAINCOCK - INSTALLATION . . . 7-26
RADIATOR DRAINCOCK - REMOVAL.......7-26
RADIATOR FAN - DESCRIPTION..........7-28
RADIATOR FAN - INSTALLATION..........7-30
RADIATOR FAN - OPERATION............7-29
RADIATOR FAN - REMOVAL.............7-30
RADIATOR FAN MOTOR - DIAGNOSIS
AND TESTING........................7-29
RADIATOR FAN RELAY - DESCRIPTION....7-30
RADIATOR FAN RELAY - INSTALLATION....7-30
RADIATOR FAN RELAY - OPERATION......7-30
RADIATOR FAN RELAY - REMOVAL.......7-30
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-26
RADIATOR PRESSURE CAP - OPERATION . . 7-27
RADIO - DESCRIPTION................8A-10
RADIO - DIAGNOSIS AND TESTING......8A-10
RADIO - INSTALLATION...............8A-11
RADIO - OPERATION..................8A-10
RADIO - REMOVAL...................8A-11
RADIO NOISE SUPPRESSION
COMPONENTS - DESCRIPTION..........8A-11
RADIO NOISE SUPPRESSION
COMPONENTS - OPERATION...........8A-12
RANGE - SPECIFICATIONS,
TRANSMITTER.......................8N-5
RANGE SENSOR - DESCRIPTION,
TRANSMISSION..............21-248,21s-150
RANGE SENSOR - INSTALLATION,
TRANSMISSION..............21-249,21s-152
RANGE SENSOR - OPERATION,
TRANSMISSION..............21-248,21s-151
RANGE SENSOR - REMOVAL,
TRANSMISSION
..............21-249,21s-151
RANGE, SPECIFICATIONS
..............8N-43
READING LAMP - INSTALLATION
........8L-23
READING LAMP - REMOVAL
............8L-23
READING/COURTESY LAMP
REPLACEMENT - STANDARD
PROCEDURE
.........................8M-3REAR - DESCRIPTION, HALF SHAFT.......3-13
REAR - DESCRIPTION, MODE DOOR
ACTUATOR..........................24-39
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL.......................9-129,9-42
REAR - INSTALLATION, HALF SHAFT......3-14
REAR - INSTALLATION, MODE DOOR
ACTUATOR..........................24-40
REAR - INSTALLATION, SPRING
MOUNTS............................2-45
REAR - INSTALLATION, WHEEL
MOUNTING STUDS...................22-22
REAR - OPERATION, MODE DOOR
ACTUATOR..........................24-40
REAR - REMOVAL, CRANKSHAFT OIL
SEAL..........................9-128,9-41
REAR - REMOVAL, HALF SHAFT..........3-13
REAR - REMOVAL, MODE DOOR
ACTUATOR..........................24-40
REAR - REMOVAL, SPRING MOUNTS......2-44
REAR - REMOVAL, WHEEL MOUNTING
STUDS.............................22-21
REAR A/C EVAPORATOR - INSTALLATION . 24-99
REAR A/C EVAPORATOR - REMOVAL.....24-97
REAR A/C EVAPORATOR LINE
EXTENSION - INSTALLATION...........24-99
REAR BLOWER MOTOR - DESCRIPTION,
POWER MODULE....................24-41
REAR BLOWER MOTOR - DIAGNOSIS
AND TESTING.......................24-58
REAR BLOWER MOTOR - INSTALLATION,
POWER MODULE......................24-42
REAR BLOWER MOTOR - OPERATION,
POWER MODULE....................24-41
REAR BLOWER MOTOR - REMOVAL,
POWER MODULE....................24-41
REAR BLOWER MOTOR RESISTOR
BLOCK - DIAGNOSIS AND TESTING......24-38
REAR BUMPER REINFORCEMENT -
INSTALLATION........................13-3
REAR BUMPER REINFORCEMENT -
REMOVAL...........................13-3
REAR COVER - INSTALLATION, FRONT
SEAT TRACK........................23-96
REAR COVER - REMOVAL, FRONT SEAT
TRACK.............................23-96
REAR COVER O-RING - INSTALLATION . . . 21-20
REAR COVER O-RING - REMOVAL.......21-19
REAR DISC BRAKE CALIPER -
INSTALLATION...................5-30,5s-29
REAR DISC BRAKE CALIPER - REMOVAL . . 5-27,
5s-26
REAR DISC BRAKE SHOES -
INSTALLATION...................5-19,5s-18
REAR DISC BRAKE SHOES - REMOVAL....5-17,
5s-16
REAR DOOR GLASS - INSTALLATION....23-111
REAR DOOR GLASS - REMOVAL.......23-111
REAR DRIVELINE MODULE -
DESCRIPTION........................3-23
REAR DRIVELINE MODULE - OPERATION . . 3-23
REAR DRIVELINE MODULE -
SPECIFICATIONS......................3-34
REAR DRIVELINE MODULE FLUIDS -
DESCRIPTION, AWD....................0-6
REAR DRIVELINE MODULE NOISE -
DIAGNOSIS AND TESTING..............3-24
REAR DRIVELINE MODULE OPERATION -
DIAGNOSIS AND TESTING..............3-26
REAR DRUM BRAKE SHOE LINING -
INSPECTION....................5-22,5s-21
REAR DRUM BRAKE SHOES -
ADJUSTMENT...................5-23,5s-22
REAR DRUM BRAKE SHOES -
INSTALLATION...................5-22,5s-21
REAR DRUM BRAKE SHOES - REMOVAL . . 5-19,
5s-18
REAR EVAP CANISTER - INSTALLATION . . . 25-20
REAR EVAP CANISTER - REMOVAL......25-19
REAR FASCIA - INSTALLATION...........13-2
REAR FASCIA - REMOVAL...............13-2
REAR FASCIA - SCUFF PAD -
INSTALLATION
........................13-4
REAR FASCIA - SCUFF PAD - REMOVAL
....13-3
REAR FLOOR HEAT DUCT -
INSTALLATION
.......................24-63
REAR FLOOR HEAT DUCT - REMOVAL
....24-62
REAR HEADER TRIM - INSTALLATION
....23-80REAR HEADER TRIM - REMOVAL........23-80
REAR HEATER CORE FILLING -
STANDARD PROCEDURE..............24-101
REAR HEATER LINES - INSTALLATION . . . 24-111
REAR HVAC - LWB - INSTALLATION,
SEAT BELT & RETRACTOR - SECOND
ROW - RIGHT OUTBOARD WITH........8O-16
REAR HVAC - LWB - REMOVAL, SEAT
BELT & RETRACTOR - SECOND ROW -
RIGHT OUTBOARD WITH..............8O-16
REAR HVAC LOUVER - INSTALLATION....23-81
REAR HVAC LOUVER - REMOVAL........23-81
REAR LATCH STRIKER - INSTALLATION . . . 23-29
REAR LATCH STRIKER - REMOVAL......23-29
REAR MOUNT - INSTALLATION.....9-134,9-50
REAR MOUNT - REMOVAL.........9-133,9-50
REAR OIL SEAL RETAINER -
INSTALLATION, CRANKSHAFT...........9-129
REAR OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT.......................9-129
REAR QUARTER PANEL/FENDER AIR
EXHAUSTER - DESCRIPTION...........23-57
REAR QUARTER PANEL/FENDER AIR
EXHAUSTER - INSTALLATION...........23-58
REAR QUARTER PANEL/FENDER AIR
EXHAUSTER - REMOVAL...............23-57
REAR SUSPENSION - DESCRIPTION......2-27
REAR SUSPENSION - OPERATION........2-28
REAR SUSPENSION FASTENER TORQUE,
SPECIFICATIONS......................2-28
REAR SUSPENSION, SPECIAL TOOLS.......2-28
REAR VIEW MIRROR - INSTALLATION....23-81
REAR VIEW MIRROR - REMOVAL........23-81
REAR WASHER PUMP MOTOR -
INSTALLATION......................8R-10
REAR WASHER PUMP MOTOR -
REMOVAL..........................8R-10
REAR WHEEL SPEED SENSOR - AWD -
INSTALLATION........................5-80
REAR WHEEL SPEED SENSOR - AWD -
REMOVAL...........................5-80
REAR WHEEL SPEED SENSOR - FWD -
INSTALLATION........................5-81
REAR WHEEL SPEED SENSOR - FWD -
REMOVAL...........................5-81
REAR WINDOW DEFOGGER RELAY -
DESCRIPTION........................8G-3
REAR WINDOW DEFOGGER RELAY -
INSTALLATION.......................8G-3
REAR WINDOW DEFOGGER RELAY -
OPERATION..........................8G-3
REAR WINDOW DEFOGGER RELAY -
REMOVAL...........................8G-3
REAR WINDOW DEFOGGER SWITCH -
DESCRIPTION........................8G-4
REAR WINDOW DEFOGGER SWITCH -
OPERATION..........................8G-4
REAR WINDOW DEFOGGER SYSTEM -
DIAGNOSIS AND TESTING..............8G-2
REAR WIPER ARM - INSTALLATION......8R-10
REAR WIPER ARM - REMOVAL.........8R-10
REAR WIPER MOTOR - INSTALLATION . . . 8R-11
REAR WIPER MOTOR - REMOVAL.......8R-11
REAR WIPER SYSTEM - DIAGNOSIS
AND TESTING........................8R-4
REAR WIPER/WASHER SWITCH -
DESCRIPTION.......................8R-11
REAR WIPER/WASHER SWITCH -
OPERATION
.........................8R-11
RECEIVE - PCM INPUT - OPERATION,
DATA BUS COMMUNICATION
...........8E-15
RECEIVER / DRIER - DESCRIPTION
......24-91
RECEIVER / DRIER - INSTALLATION
......24-92
RECEIVER / DRIER - OPERATION
........24-91
RECEIVER / DRIER - REMOVAL
.........24-91
RECIRCULATION DOOR ACTUATOR -
DESCRIPTION
.......................24-32
RECIRCULATION DOOR ACTUATOR -
INSTALLATION
.......................24-33
RECIRCULATION DOOR ACTUATOR -
OPERATION
.........................24-32
RECIRCULATION DOOR ACTUATOR -
REMOVAL
..........................24-33
RECLINER HANDLE - INSTALLATION
.....23-90
RECLINER HANDLE - REMOVAL
.........23-90
RECOVERY - STANDARD PROCEDURE,
REFRIGERANT
.......................24-71
RSINDEX27
Description Group-Page Description Group-Page Description Group-Page

STRIKER - REMOVAL, LATCH . 23-19,23-41,23-62
STRIKER - REMOVAL, REAR LATCH......23-29
STRIPPED THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD..............9-145
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS....................23-156
STRUCTURAL COLLAR - INSTALLATION....9-48
STRUCTURAL COLLAR - REMOVAL.......9-47
STRUT ASSEMBLY - ASSEMBLY..........2-23
STRUT ASSEMBLY - DESCRIPTION.......2-19
STRUT ASSEMBLY - DIAGNOSIS AND
TESTING............................2-20
STRUT ASSEMBLY - DISASSEMBLY.......2-21
STRUT ASSEMBLY - INSTALLATION.......2-25
STRUT ASSEMBLY - OPERATION.........2-20
STRUT ASSEMBLY - REMOVAL...........2-21
STUDS - FRONT - INSTALLATION,
WHEEL MOUNTING...................22-21
STUDS - FRONT - REMOVAL, WHEEL
MOUNTING.........................22-20
STUDS - REAR - INSTALLATION, WHEEL
MOUNTING.........................22-22
STUDS - REAR - REMOVAL, WHEEL
MOUNTING.........................22-21
SUCTION LINE - INSTALLATION . . . 24-107,24-95
SUCTION LINE - REMOVAL.......24-106,24-94
SUN VISOR - INSTALLATION...........23-82
SUN VISOR - REMOVAL...............23-82
SUN VISOR SUPPORT - INSTALLATION.....23-83
SUN VISOR SUPPORT - REMOVAL.......23-83
SUNROOF - DESCRIPTION............23-116
SUNROOF - DIAGNOSIS AND TESTING . . . 23-116
SUNROOF ASSEMBLY - INSTALLATION . . 23-120
SUNROOF ASSEMBLY - REMOVAL......23-120
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-120
SUNROOF MOTOR - INSTALLATION.....23-121
SUNROOF MOTOR - REMOVAL.........23-121
SUNROOF SWITCH - INSTALLATION.....23-123
SUNROOF SWITCH - REMOVAL........23-123
SUNSHADE - INSTALLATION...........23-121
SUNSHADE - REMOVAL..............23-120
SUPPLEMENTAL CABIN HEATER -
DIAGNOSIS AND TESTING, DIESEL......24-113
SUPPLEMENTAL DIESEL HEATER
WIRING - INSTALLATION.............24-119
SUPPLEMENTAL DIESEL HEATER
WIRING - REMOVAL.................24-119
SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT ..............................8E-15
SUPPLY - PCM OUTPUT - SBEC
CONTROLLER - OPERATION, 8-VOLT.....8E-15
SUPPORT - INSTALLATION, LUMBAR....23-106
SUPPORT - INSTALLATION, SUN VISOR . . . 23-83
SUPPORT - REMOVAL, LUMBAR.......23-106
SUPPORT - REMOVAL, SUN VISOR......23-83
SUPPORT CYLINDER - INSTALLATION....23-43
SUPPORT CYLINDER - REMOVAL........23-43
SUPPORT PLATE - DRUM BRAKE -
INSTALLATION...................5-56,5s-58
SUPPORT PLATE - DRUM BRAKE -
REMOVAL......................5-56,5s-58
SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO NOISE...........8A-11
SUPPRESSION COMPONENTS -
OPERATION, RADIO NOISE.............8A-12
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET.......9-11,9-85
SUSPENSION - DESCRIPTION, FRONT......2-2
SUSPENSION - DESCRIPTION, REAR
......2-27
SUSPENSION - OPERATION, FRONT
........2-2
SUSPENSION - OPERATION, REAR
........2-28
SUSPENSION AND STEERING -
DIAGNOSIS AND TESTING
..............2-50
SUSPENSION FASTENER TORQUE,
SPECIFICATIONS - FRONT
................2-3
SUSPENSION FASTENER TORQUE,
SPECIFICATIONS - REAR
................2-28
SUSPENSION, SPECIAL TOOLS - FRONT
....2-3
SUSPENSION, SPECIAL TOOLS - REAR
....2-28
SWITCH - DESCRIPTION
................8P-6
SWITCH - DESCRIPTION, AUTOSTICK
. . . 21-189
SWITCH - DESCRIPTION, BRAKE FLUID
LEVEL
..........................5-10,5s-9
SWITCH - DESCRIPTION, BRAKE LAMP
....8L-4
SWITCH - DESCRIPTION, DOOR
CYLINDER LOCK
.....................8N-40SWITCH - DESCRIPTION, DRIVER
HEATED SEAT ........................8G-8
SWITCH - DESCRIPTION, DRIVER SEAT . . 8N-10,
8N-53
SWITCH - DESCRIPTION, EXTERIOR
HANDLE...........................8N-11
SWITCH - DESCRIPTION, FULL OPEN....8N-12,
8N-31
SWITCH - DESCRIPTION, HORN..........8H-5
SWITCH - DESCRIPTION, LEFT B-PILLAR . 8N-32
SWITCH - DESCRIPTION, MEMORY SET . . 8N-12,
8N-55
SWITCH - DESCRIPTION, OIL PRESSURE . 9-141
SWITCH - DESCRIPTION, PASSENGER
HEATED SEAT .......................8G-12
SWITCH - DESCRIPTION, PASSENGER
SEAT.........................8N-13,8N-56
SWITCH - DESCRIPTION, REAR
WINDOW DEFOGGER..................8G-4
SWITCH - DESCRIPTION, REAR
WIPER/WASHER.....................8R-11
SWITCH - DESCRIPTION, RIGHT
B-PILLAR..........................8N-32
SWITCH - DIAGNOSIS AND TESTING,
BRAKE LAMP........................8L-4
SWITCH - DIAGNOSIS AND TESTING,
DOOR CYLINDER LOCK...............8N-40
SWITCH - DIAGNOSIS AND TESTING,
DOOR LOCK....................8N-4,8N-41
SWITCH - DIAGNOSIS AND TESTING,
DRIVER HEATED SEAT.................8G-9
SWITCH - DIAGNOSIS AND TESTING,
DRIVER SEAT...................8N-11,8N-54
SWITCH - DIAGNOSIS AND TESTING,
FAILED PARK........................8R-2
SWITCH - DIAGNOSIS AND TESTING,
FRONT WIPER/WASHER................8R-2
SWITCH - DIAGNOSIS AND TESTING,
HEADLAMP.........................8L-12
SWITCH - DIAGNOSIS AND TESTING,
MEMORY.....................8N-13,8N-56
SWITCH - DIAGNOSIS AND TESTING,
MULTI-FUNCTION....................8L-18
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER HEATED SEAT.............8G-13
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER SEAT..............8N-14,8N-57
SWITCH - DIAGNOSIS AND TESTING,
REMOTE...........................8N-49
SWITCH - DIAGNOSIS AND TESTING,
TRACTION CONTROL...................5-82
SWITCH - DIAGNOSIS AND TESTING,
WINDOW...........................8N-64
SWITCH - EXPORT - DESCRIPTION,
DOOR CYLINDER LOCK................8N-3
SWITCH - EXPORT - DESCRIPTION,
POWER FOLDAWAY MIRROR...........8N-48
SWITCH - EXPORT - DIAGNOSIS AND
TESTING, DOOR CYLINDER LOCK........8N-3
SWITCH - EXPORT - INSTALLATION,
DOOR CYLINDER LOCK................8N-4
SWITCH - EXPORT - INSTALLATION,
HOOD AJAR.........................8Q-3
SWITCH - EXPORT - INSTALLATION,
POWER FOLDAWAY MIRROR
...........8N-49
SWITCH - EXPORT - OPERATION, DOOR
CYLINDER LOCK
......................8N-3
SWITCH - EXPORT - OPERATION,
POWER FOLDAWAY MIRROR
...........8N-48
SWITCH - EXPORT - REMOVAL, DOOR
CYLINDER LOCK
......................8N-3
SWITCH - EXPORT - REMOVAL, HOOD
AJAR
...............................8Q-3
SWITCH - EXPORT - REMOVAL, POWER
FOLDAWAY MIRROR
..................8N-48
SWITCH - INSTALLATION
...............8P-6
SWITCH - INSTALLATION, ADJUSTABLE
PEDALS
............................5s-10
SWITCH - INSTALLATION, BACK-UP
LAMP
..............................21-62
SWITCH - INSTALLATION, BRAKE FLUID
LEVEL
.........................5-11,5s-10
SWITCH - INSTALLATION, BRAKE LAMP
. . . 8L-5
SWITCH - INSTALLATION, CENTER
CONSOLE LAMP
.....................8L-21
SWITCH - INSTALLATION, CLUTCH
PEDAL INTERLOCK
....................6-14SWITCH - INSTALLATION, CLUTCH
PEDAL UPSTOP.......................6-16
SWITCH - INSTALLATION, DOOR
CYLINDER LOCK.....................8N-41
SWITCH - INSTALLATION, DOOR LOCK....8N-4,
8N-42
SWITCH - INSTALLATION, DRIVER
HEATED SEAT .......................8G-10
SWITCH - INSTALLATION, DRIVER SEAT . . 8N-12,
8N-55
SWITCH - INSTALLATION, EXTERIOR
HANDLE...........................8N-12
SWITCH - INSTALLATION, FULL OPEN....8N-13
SWITCH - INSTALLATION, GLOVE BOX
LAMP..............................8L-22
SWITCH - INSTALLATION, HEADLAMP....8L-13
SWITCH - INSTALLATION, IGNITION......19-16
SWITCH - INSTALLATION, LEFT
B-PILLAR..........................8N-32
SWITCH - INSTALLATION, MEMORY SET . 8N-13,
8N-56
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-18
SWITCH - INSTALLATION, OIL
PRESSURE.....................9-141,9-54
SWITCH - INSTALLATION, PASSENGER
HEATED SEAT .......................8G-14
SWITCH - INSTALLATION, PASSENGER
SEAT.........................8N-15,8N-57
SWITCH - INSTALLATION, REMOTE......8N-49
SWITCH - INSTALLATION, RIGHT
B-PILLAR..........................8N-32
SWITCH - INSTALLATION, SUNROOF....23-123
SWITCH - INSTALLATION, WASHER
FLUID LEVEL........................8R-12
SWITCH - INSTALLATION, WINDOW.....8N-65
SWITCH - OPERATION.................8P-6
SWITCH - OPERATION, AUTOSTICK.....21-189
SWITCH - OPERATION, BRAKE FLUID
LEVEL..........................5-10,5s-9
SWITCH - OPERATION, BRAKE LAMP......8L-4
SWITCH - OPERATION, DOOR CYLINDER
LOCK..............................8N-40
SWITCH - OPERATION, DRIVER HEATED
SEAT ...............................8G-8
SWITCH - OPERATION, DRIVER SEAT....8N-11,
8N-54
SWITCH - OPERATION, EXTERIOR
HANDLE...........................8N-11
SWITCH - OPERATION, FULL OPEN . 8N-12,8N-31
SWITCH - OPERATION, LEFT B-PILLAR . . . 8N-32
SWITCH - OPERATION, MEMORY SET . . . 8N-13,
8N-56
SWITCH - OPERATION, OIL PRESSURE . . . 9-141
SWITCH - OPERATION, PASSENGER
HEATED SEAT .......................8G-12
SWITCH - OPERATION, PASSENGER
SEAT.........................8N-13,8N-56
SWITCH - OPERATION, REAR WINDOW
DEFOGGER..........................8G-4
SWITCH - OPERATION, REAR WIPER/
WASHER...........................8R-11
SWITCH - OPERATION, RIGHT B-PILLAR . . 8N-32
SWITCH - REMOVAL...................8P-6
SWITCH - REMOVAL, ADJUSTABLE
PEDALS............................5s-10
SWITCH - REMOVAL, BACK-UP LAMP....21-62
SWITCH - REMOVAL, BRAKE FLUID
LEVEL.........................5-11,5s-10
SWITCH - REMOVAL, BRAKE LAMP.......8L-5
SWITCH - REMOVAL, CENTER CONSOLE
LAMP..............................8L-21
SWITCH - REMOVAL, CLUTCH PEDAL
INTERLOCK..........................6-13
SWITCH - REMOVAL, CLUTCH PEDAL
UPSTOP.............................6-15
SWITCH - REMOVAL, DOOR CYLINDER
LOCK..............................8N-41
SWITCH - REMOVAL, DOOR LOCK . . 8N-4,8N-42
SWITCH - REMOVAL, DRIVER HEATED
SEAT ..............................8G-10
SWITCH - REMOVAL, DRIVER SEAT.....8N-12,
8N-55
SWITCH - REMOVAL, EXTERIOR HANDLE
. 8N-11
SWITCH - REMOVAL, FULL OPEN
.......8N-13
SWITCH - REMOVAL, GLOVE BOX LAMP
. . 8L-22
SWITCH - REMOVAL, HEADLAMP
........8L-13
SWITCH - REMOVAL, IGNITION
.........19-14
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page