skim CHRYSLER VOYAGER 2005 User Guide

(19) Disconnect the column harness wiring connec-
tors from the Brake Transmission Shift Interlock
(BTSI) and ignition switch (Fig. 11).
(20) Disconnect the column harness wiring connec-
tor for the multi-function switch (Fig. 12).(21) Disconnect the column harness wiring connec-
tors for the clockspring and SQUIB (Fig. 12).
(22) If equipped with Sentry Key Immobilizer, dis-
connect the wiring connector from the SKIM (Fig.
13).
(23) Remove screw fastening horn ground wire to
column (Fig. 14).
Fig. 11 Ignition Switch And BTSI Wiring
Connections
1 - WIRING CONNECTOR
2 - IGNITION SWITCH
3 - BTSI
4 - WIRING CONNECTOR
Fig. 12 Multi-function And Clockspring Wiring
Connections
1 - MULTI-FUNCTION SWITCH MOUNTING HOUSING
2 - MULTI-FUNCTION WIRING CONNECTOR
3 - CLOCKSPRING WIRING CONNECTOR
4 - CLOCKSPRING SQUIB WIRING CONNECTOR
Fig. 13 Sentry Key Immobilizer Module
1 - WIRING CONNECTOR
2 - IGNITION KEY CYLINDER HALO
3 - SKIM
4 - MOUNTING SCREW
Fig. 14 Horn Ground At Column
1 - STEERING COLUMN
2 - HORN GROUND WIRE
3 - SCREW
19 - 14 COLUMNRS
COLUMN (Continued)

(31) If the steering column is being replaced, slide
the multi-function switch mounting housing off the
column (Fig. 19).
(32) If the steering column is being replaced,
remove the mounting screw fastening the SKIM to
the ignition key cylinder housing (Fig. 13). Remove
the SKIM.
(33) If the steering column is being replaced,
remove the halo from the ignition key cylinder hous-
ing (Fig. 13).
(34) If the steering column is being replaced,
remove the ignition key lock cylinder (Refer to 19 -
STEERING/COLUMN/KEY/LOCK CYLINDER -
REMOVAL).
INSTALLATION
NOTE: Before proceeding, (Refer to 19 - STEERING/
COLUMN - WARNING)(Refer to 8 - ELECTRICAL/RE-
STRAINTS/DRIVER AIRBAG - REMOVAL).
NOTE: Make sure the front wheels of the vehicle are
still in the STRAIGHT AHEAD position before begin-
ning the column installation procedure.
(1) If removed, install the ignition key lock cylin-
der (Refer to 19 - STEERING/COLUMN/KEY/LOCK
CYLINDER - INSTALLATION).
(2) If removed, install the halo on the ignition key
cylinder housing (Fig. 13).(3) If removed, install SKIM (Fig. 13). Install the
mounting screw fastening the SKIM to the ignition
key cylinder housing. Tighten the screw to 4 N´m (30
in. lbs.) torque.
(4) If removed, slide the multi-function switch
mounting housing onto the column (Fig. 19).
(5) If multi-function switch mounting housing is
being installed, install the set-screw fastening the
housing to the column (Fig. 18). Tighten the set-
screw to 14 N´m (124 in. lbs.) torque.
(6) Install the steering column (Fig. 17). Slide the
column lower mounting slots over the lower mount-
ing studs (with nuts started) first, then lift column
into place over the upper mounting studs.
(7) Install the two upper mounting nuts (Fig. 17).
Tighten the two upper mounting nuts, then the two
lower mounting nuts to 12 N´m (105 in. lbs.) torque.
(8) Match the column shaft coupling to the inter-
mediate shaft and install the pinch bolt (Fig. 16).
Tighten the pinch bolt nut to 28 N´m (250 in. lbs.)
torque. Install the hair pin in the end of the pinch
bolt.
(9) Feed the shift cable through the bracket on the
column (Fig. 15), then install the clip fastening the
cable housing to the bracket.
(10) Connect the shift cable to the lever pin (Fig.
15).
(11) Install the screw fastening the horn ground
wire to the column (Fig. 14). Tighten the screw to 7
N´m (60 in. lbs.) torque.
(12) If equipped with Sentry Key Immobilizer, con-
nect the wiring connector to the SKIM (Fig. 13).
(13) Connect the column harness wiring connectors
for the clockspring and SQUIB (Fig. 12).
(14) Connect the column harness wiring connector
for the multi-function switch (Fig. 12).
(15) Connect the column harness wiring connectors
for the Brake Transmission Shift Interlock (BTSI)
and ignition switch (Fig. 11).
(16) Install the fixed shroud (Fig. 10). Install the
screws fastening the fixed shroud in place and
tighten the screws to 3 N´m (23 in. lbs.) torque.
(17) If equipped with Autostick, connect the wiring
connector (Fig. 9).
(18) If equipped with traction control, position the
upper shroud above the column and route the switch
wiring down around the column. Connect the wiring
connector from the column wiring harness to the
traction control switch wiring (attached to upper
shroud) (Fig. 9).
Fig. 19 Multi-Function Switch Mounting Housing
1 - MULTI-FUNCTION SWITCH MOUNTING HOUSING
2 - STEERING COLUMN
19 - 16 COLUMNRS
COLUMN (Continued)

(19) Position the lower shroud on the column (Fig.
8). Install the lower shroud mounting screw. Tighten
the screw to 2 N´m (17 in. lbs.) torque.
(20) If equipped with adjustable pedals, Connect
the wiring connector for the switch (Fig. 7) to the col-
umn wiring harness.
(21) Position the upper shroud on top of the lower
shroud and snap it into place. Install the upper
shroud mounting screws (Fig. 6). Tighten the screws
to 2 N´m (17 in. lbs.) torque.
(22) Inspect shroud mating surfaces for excessive
gaps and correct as necessary.
(23) Install the cluster trim bezel (Refer to 23 -
BODY/INSTRUMENT PANEL/CLUSTER BEZEL -
INSTALLATION).
(24) Install the knee blocker/steering column cover
plate. (Refer to 23 - BODY/INSTRUMENT PANEL/
KNEE BLOCKER - INSTALLATION)
(25) Install the parking brake handle link.
(26) Install the knee blocker/steering column open-
ing cover. (Refer to 23 - BODY/INSTRUMENT PAN-
EL/STEERING COLUMN OPENING COVER -
INSTALLATION)
(27) Align the splines and install the steering
wheel on the steering column shaft(Refer to 19 -
STEERING/COLUMN/STEERING WHEEL -
INSTALLATION).
(28) Install the damper over the steering column
shaft (Fig. 4).
(29) Install the steering wheel retaining bolt (Fig.
4). Tighten the bolt to 61 N´m (45 ft. lbs.) torque.
(30) If the steering wheel is equipped with remote
audio controls, connect the wiring connector to the
clockspring (Fig. 4).
(31) Connect the two squib connectors to the
driver airbag (Fig. 3). The connectors are color coded
to avoid connector mix-up.
(32) Connect the speed control and horn connector
to the clockspring (Fig. 3).
(33) Install the airbag to the steering wheel.
Install the driver airbag mounting screws (Fig. 2).
Tighten screws to 10 N´m (90 in. lbs.) torque.
(34) Connect the battery negative (ground) cable to
battery post following special Diagnosis And Testing
procedure. (Refer to 8 - ELECTRICAL/RESTRAINTS
- DIAGNOSIS AND TESTING)
(35) Check operation of all steering column
mounted components.
(36) Road test vehicle to ensure proper operation
of steering.SPECIFICATIONS
COLUMN FASTENER TORQUE
DESCRIPTION N´mFt.
Lbs.In.
Lbs.
Driver Airbag Mounting Screws 10 Ð 90
Multi-Function Switch Mounting
Housing Set-Screw14 Ð 124
Shroud Attaching Screws - Fixed 3 Ð 23
Shroud Attaching Screws -
Lower/Upper2Ð17
SKIM Attaching Screw 4 Ð 30
Steering Column Coupling Pinch
Bolt28 Ð 250
Steering Column Mounting Nuts 12 Ð 105
Steering Wheel Retaining Bolt 61 45 Ð
IGNITION SWITCH
REMOVAL
The ignition switch attaches to the lock cylinder
housing on the end opposite the lock cylinder (Fig.
20). For ignition switch terminal and circuit identifi-
cation, refer to the appropriate wiring information.
The wiring information includes wiring diagrams,
proper wire and connector repair procedures, further
details on wire harness routing and retention, as well
as pin-out and location views for the various wire
harness connectors, splices and grounds.
(1) Disconnect negative cable from battery.
Fig. 20 Ignition SwitchÐViewed From Below
Column
1 - IGNITION SWITCH
2 - LOCK CYLINDER HOUSING
3 - RETAINING TABS
RSCOLUMN19-17
COLUMN (Continued)

PANEL TOP COVER - REMOVAL,INSTRUMENT ....................... 23-72
PANEL TOP PAD ASSEMBLY - INSTALLATION, INSTRUMENT ...........23-77
PANEL TOP PAD ASSEMBLY - REMOVAL, INSTRUMENT ....................... 23-77
PANEL/FENDER AIR EXHAUSTER - DESCRIPTION, REAR QUARTER .........23-59
PANEL/FENDER AIR EXHAUSTER - INSTALLATION, REAR QUARTER .........23-60
PANEL/FENDER AIR EXHAUSTER - REMOVAL, REAR QUARTER ............23-59
PANEL-THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, BOTTOM OF SEAT
CUSHION PAN ...................... 23-152
PANEL-THIRD ROW - FOLD-IN-FLOOR - REMOVAL, BOTTOM OF SEAT
CUSHION PAN ...................... 23-152
PARK ASSIST DISPLAY - DESCRIPTION ....8B-3
PARK ASSIST DISPLAY - INSTALLATION . . . 8B-4
PARK ASSIST DISPLAY - OPERATION .....8B-3
PARK ASSIST DISPLAY - REMOVAL .......8B-4
PARK ASSIST MODULE - DESCRIPTION ....8B-4
PARK ASSIST MODULE - INSTALLATION . . . 8B-6
PARK ASSIST MODULE - OPERATION .....8B-5
PARK ASSIST MODULE - REMOVAL .......8B-5
PARK ASSIST SENSOR - DESCRIPTION ....8B-6
PARK ASSIST SENSOR - INSTALLATION . . . 8B-6
PARK ASSIST SENSOR - OPERATION ......8B-6
PARK ASSIST SENSOR - REMOVAL .......8B-6
PARK SWITCH - DIAGNOSIS AND TESTING, FAILED ..................... 8R-2
PARKING BRAKE - INSTALLATION, LEVER .............................. 5-76
PARKING BRAKE - INSTALLATION, SHOES .............................. 5-84
PARKING BRAKE - REMOVAL, LEVER ......5-75
PARKING BRAKE - REMOVAL, SHOES .....5-78
PARKING BRAKE AUTOMATIC ADJUSTER TENSION RELEASE - STANDARD
PROCEDURE ......................... 5-63
PARKING BRAKE AUTOMATIC ADJUSTER TENSION RESET - STANDARD
PROCEDURE ......................... 5-64
PARKING BRAKE CABLES - ADJUSTMENT ........................ 5-65
PARKING BRAKE INTERMEDIATE - INSTALLATION, CABLE .................5-69
PARKING BRAKE INTERMEDIATE - REMOVAL, CABLE ..................... 5-69
PARKING BRAKE LEVER AND FRONT CABLE - INSTALLATION ................5-77
PARKING BRAKE LEVER AND FRONT CABLE - REMOVAL .................... 5-77
PARKING BRAKE SHOES - ADJUSTMENT . . . 5-85
PARK/TURN SIGNAL LAMP - INSTALLATION ....................... 8L-18
PARK/TURN SIGNAL LAMP - REMOVAL . . . 8L-18
PARTS - DESCRIPTION, FFV REPLACEMENT ....................... 14-2
PASSENGER AIRBAG - DESCRIPTION ....8O-30
PASSENGER AIRBAG - INSTALLATION ....8O-32
PASSENGER AIRBAG - OPERATION ......8O-30
PASSENGER AIRBAG - REMOVAL ........8O-30
PASSENGER AIRBAG DISABLED INDICATOR - DESCRIPTION ............8O-33
PASSENGER AIRBAG DISABLED INDICATOR - INSTALLATION ............8O-34
PASSENGER AIRBAG DISABLED INDICATOR - OPERATION ..............8O-33
PASSENGER AIRBAG DISABLED INDICATOR - REMOVAL ...............8O-34
PASSENGER BENCH - INSTALLATION, SEAT BELT BUCKLE - SECOND ROW -
THREE ............................. 8O-40
PASSENGER BENCH - REMOVAL, SEAT BELT BUCKLE - SECOND ROW - THREE . . . 8O-40
PATTERNS - DIAGNOSIS AND TESTING, TIRE WEAR ......................... 22-16
PCM GROUND - OPERATION ...........8E-14
PCM INPUT - OPERATION, DATA BUS COMMUNICATION RECEIVE .............8E-14
PCM INPUT - OPERATION, IGNITION SENSE ............................. 8E-14
PCM INPUT - OPERATION, SENSOR RETURN ............................ 8E-14
PCM OUTPUT - OPERATION, 5 VOLT SUPPLY ............................ 8E-15PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE ......................... 8E-1
PCV SYSTEM - DIAGNOSIS AND TESTING ........................... 25-18
PCV VALVE - DESCRIPTION ............25-18
PCV VALVE - OPERATION ..............25-18
PEDAL - INSTALLATION, ACCELERATOR . . . 14-28
PEDAL - REMOVAL, ACCELERATOR ......14-28
PEDAL TORQUE SHAFT - RHD - INSTALLATION ........................ 5-44
PEDAL TORQUE SHAFT - RHD - REMOVAL ........................... 5-44
PEDALS - ADJUSTABLE - INSTALLATION . . . 5-43
PEDALS - ADJUSTABLE - REMOVAL .......5-40
PEDALS SWITCH - INSTALLATION, ADJUSTABLE ......................... 5-11
PEDALS SWITCH - REMOVAL, ADJUSTABLE ......................... 5-11
PERFORMANCE - DIAGNOSIS AND TESTING, ENGINE DIAGNOSIS ........9-4,9-80
PERFORMANCE TEST, DIAGNOSIS AND TESTING - A/C ........................ 24-7
PERFORMANCE TEST, DIAGNOSIS AND TESTING - HEATER ................... 24-10
PIN BUSHINGS (CONTINENTAL TEVES BRAKES) - ASSEMBLY, CALIPER GUIDE ....5-25
PIN BUSHINGS (CONTINENTAL TEVES BRAKES) - DISASSEMBLY, CALIPER
GUIDE .............................. 5-24
PINCH SENSOR - DESCRIPTION .........8N-17
PINCH SENSOR - INSTALLATION ........8N-18
PINCH SENSOR - OPERATION ..........8N-17
PINCH SENSOR - REMOVAL ............8N-18
PINION FACTOR SETTING - STANDARD PROCEDURE ........................ 8E-15
PINS (TRW BRAKES) - INSTALLATION, DISC BRAKE CALIPER GUIDE ............5-32
PINS (TRW BRAKES) - REMOVAL, DISC BRAKE CALIPER GUIDE ................5-31
PIPE - 3.3/3.8L - INSTALLATION, CROSS-OVER ........................ 11-6
PIPE - 3.3/3.8L - REMOVAL, CROSS- OVER ............................... 11-6
PIPE - INSTALLATION, AIR INTAKE ......24-115
PIPE - REMOVAL, AIR INTAKE .........24-115
PIPES - INSTALLATION, HEATER ........24-120
PIPES - REMOVAL, HEATER ...........24-119
PISTON & CONNECTING ROD - DESCRIPTION ................... 9-119,9-44
PISTON & CONNECTING ROD - INSTALLATION ........................ 9-45
PISTON & CONNECTING ROD - REMOVAL ........................... 9-44
PISTON AND SEAL - ASSEMBLY, CALIPER ........................ 5-26,5-30
PISTON AND SEAL - DISASSEMBLY, CALIPER ........................ 5-24,5-28
PISTON RING, FITTING .................9-47
PISTON RING FITTING - STANDARD PROCEDURE ........................ 9-124
PISTON RINGS - INSTALLATION .........9-124
PISTON RINGS - REMOVAL ............9-124
PISTON TO CYLINDER BORE FITTING - STANDARD PROCEDURE ................9-44
PISTONS - STANDARD PROCEDURE, FITTING ............................ 9-120
PLANETARY GEARTRAIN - DESCRIPTION ................ 21-112,21-263
PLANETARY GEARTRAIN - OPERATION . . 21-112, 21-263
PLASTIC BODY PANEL REPAIR - STANDARD PROCEDURE ................23-3
PLASTIC GROCERY BAG RETAINER - INSTALLATION ...................... 23-149
PLASTIC GROCERY BAG RETAINER - REMOVAL ......................... 23-149
PLASTIGAGE - STANDARD PROCEDURE, MEASURING BEARING CLEARANCE
USING .......................... 9-12,9-86
PLATINUM PLUGS - DESCRIPTION ........8I-9
PLAYER - DESCRIPTION, DVD ..........8A-12
PLAYER - INSTALLATION, DVD ..........8A-12
PLAYER - REMOVAL, DVD .............8A-12
PLUG CABLE - DESCRIPTION, SPARK .....8I-10
PLUG CABLE RESISTANCE, SPECIFICATIONS - SPARK ...............8I-2
PLUG, SPECIFICATIONS - SPARK .........8I-2
PLUGS - DESCRIPTION, PLATINUM ........8I-9PLUGS - STANDARD PROCEDURE,
ENGINE CORE AND OIL GALLERY ....9-10,9-88
PLUMBING - FRONT - DESCRIPTION .....24-65
PLUMBING - FRONT - OPERATION .......24-65
POINTS - DESCRIPTION, LUBRICATION .....0-7
POLISHING - DESCRIPTION, FINESSE SANDING/BUFFING .................. 23-101
PORT REPAIR - STANDARD PROCEDURE, INTAKE MANIFOLD
VACUUM ........................... 9-148
PORT VALVE CORE - DESCRIPTION, SERVICE ........................... 24-95
PORT VALVE CORE - INSTALLATION, SERVICE ........................... 24-95
PORT VALVE CORE - REMOVAL, SERVICE ........................... 24-95
POSITION SENSOR - DESCRIPTION, CAMSHAFT ........................... 8I-4
POSITION SENSOR - DESCRIPTION, CRANKSHAFT ....................... 14-29
POSITION SENSOR - DESCRIPTION, THROTTLE .......................... 14-40
POSITION SENSOR - OPERATION, CAMSHAFT ........................... 8I-4
POSITION SENSOR - OPERATION, CRANKSHAFT ....................... 14-29
POSITION SENSOR - OPERATION, THROTTLE .......................... 14-41
POSITION SENSOR - REMOVAL, CRANKSHAFT ....................... 14-30
POTENTIAL - STANDARD PROCEDURE, TESTING OF VOLTAGE ..............8W-01-9
POWER - INSTALLATION, WINDOW REGULATOR ........................ 23-22
POWER - REMOVAL, WINDOW REGULATOR ........................ 23-22
POWER ADJUSTER - INSTALLATION, FRONT SEAT TRACK .................23-124
POWER ADJUSTER - REMOVAL, FRONT SEAT TRACK ....................... 23-124
POWER BRAKE BOOSTER - DESCRIPTION ........................ 5-45
POWER BRAKE BOOSTER - DIAGNOSIS AND TESTING ........................ 5-46
POWER BRAKE BOOSTER - OPERATION . . . 5-46
POWER DISTRIBUTION SYSTEM - DESCRIPTION .....................8W -97-1
POWER DISTRIBUTION SYSTEM - OPERATION .......................8W -97-1
POWER DISTRIBUTION SYSTEMS, SPECIAL TOOLS ...................8W -97-1
POWER FOLDAWAY MIRROR SWITCH - EXPORT - DESCRIPTION ...............8N-29
POWER FOLDAWAY MIRROR SWITCH - EXPORT - INSTALLATION ..............8N-30
POWER FOLDAWAY MIRROR SWITCH - EXPORT - OPERATION ................8N-29
POWER FOLDAWAY MIRROR SWITCH - EXPORT - REMOVAL .................. 8N-29
POWER LIFTGATE CONTROL MODULE - DESCRIPTION ....................... 8E-10
POWER LIFTGATE CONTROL MODULE - OPERATION ......................... 8E-10
POWER LIFTGATE CONTROL MODULE, DIAGNOSIS AND TESTING .............8E-10
POWER LIFTGATE LEARN CYCLE, STANDARD PROCEDURE ...............8N-8
POWER LIFTGATE SYSTEM - DESCRIPTION ........................ 8N-2
POWER LIFTGATE SYSTEM - OPERATION . . 8N-2
POWER LIFTGATE SYSTEM, DIAGNOSIS AND TESTING ........................ 8N-3
POWER LOCKS - DESCRIPTION .........8N-20
POWER LOCKS - OPERATION ...........8N-21
POWER MIRRORS - DESCRIPTION ......8N-26
POWER MIRRORS - OPERATION ........8N-26
POWER MIRRORS, DIAGNOSIS AND TESTING ........................... 8N-27
POWER MODULE - BLOWER MOTOR - DESCRIPTION ....................... 24-30
POWER MODULE - BLOWER MOTOR - INSTALLATION ....................... 24-31
POWER MODULE - BLOWER MOTOR - OPERATION ......................... 24-30
POWER MODULE - BLOWER MOTOR - REMOVAL .......................... 24-30
POWER MODULE - DESCRIPTION, INTEGRATED ......................8W -97-1
RS INDEX23
Description Group-Page Description Group-Page Description Group-Page

POWER MODULE - INSTALLATION,INTEGRATED ......................8W -97-2
POWER MODULE - OPERATION, INTEGRATED ......................8W -97-2
POWER MODULE - REAR BLOWER MOTOR - DESCRIPTION ...............24-40
POWER MODULE - REAR BLOWER MOTOR - INSTALLATION ...............24-41
POWER MODULE - REAR BLOWER MOTOR - OPERATION .................24-40
POWER MODULE - REAR BLOWER MOTOR - REMOVAL .................. 24-41
POWER MODULE - REMOVAL, INTEGRATED ......................8W -97-2
POWER OUTLET - DESCRIPTION ......8W-97-3
POWER OUTLET - DIAGNOSIS & TESTING .........................8W -97-3
POWER OUTLET - OPERATION ........8W-97-3
POWER SEAT SYSTEM, DESCRIPTION ....8N-31
POWER SEAT SYSTEM, DIAGNOSIS AND TESTING ........................... 8N-33
POWER SEAT SYSTEM, OPERATION .....8N-32
POWER SEAT TRACK - DESCRIPTION ....8N-37
POWER SEAT TRACK - OPERATION ......8N-38
POWER SEAT TRACK, DIAGNOSIS AND TESTING ........................... 8N-38
POWER SLIDING DOOR ADJUSTMENT, STANDARD PROCEDURE ..............8N-49
POWER SLIDING DOOR LEARN CYCLE, STANDARD PROCEDURE ..............8N-48
POWER SLIDING DOOR SYSTEM - DESCRIPTION ........................ 8N-40
POWER SLIDING DOOR SYSTEM - OPERATION ......................... 8N-41
POWER SLIDING DOOR SYSTEM, DIAGNOSIS AND TESTING .............8N-42
POWER STEERING BELT TENSION - STANDARD PROCEDURE, CHECKING .......7-8
POWER STEERING FASTENER TORQUE, SPECIFICATIONS ...................... 19-9
POWER STEERING FLUID LEVEL CHECKING - STANDARD PROCEDURE ....19-44
POWER STEERING GEAR, SPECIAL TOOLS ............................. 19-34
POWER STEERING PUMP INITIAL OPERATION - STANDARD PROCEDURE . . . 19-37
POWER STEERING PUMP, SPECIAL TOOLS ............................. 19-44
POWER STEERING, SPECIAL TOOLS ......19-9
POWER STEERING SYSTEM - DESCRIPTION ........................ 19-1
POWER STEERING SYSTEM - OPERATION .......................... 19-1
POWER STEERING SYSTEM FLOW AND PRESSURE TEST - DIAGNOSIS AND
TESTING ............................ 19-1
POWER TRANSFER UNIT FLUID - DESCRIPTION, AWD ....................0-6
POWER WINDOWS - DESCRIPTION ......8N-61
POWER WINDOWS - OPERATION ........8N-61
POWER WINDOWS, DIAGNOSIS AND TESTING ........................... 8N-61
POWERING SEVERAL LOADS - STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRELOAD - ADJUSTMENT, DIFFERENTIAL BEARING ..............21-228
PRELOAD MEASUREMENT AND ADJUSTMENT, ADJUSTMENTS -
DIFFERENTIAL BEARING ...............21-79
PREPARATION - STANDARD PROCEDURE, ENGINE GASKET
SURFACE ........................ 9-11,9-87
PRESSURE - DIAGNOSIS AND TESTING, CHECKING ENGINE OIL .................9-53
PRESSURE - DIAGNOSIS AND TESTING, ENGINE OIL ......................... 9-138
PRESSURE CAP - DESCRIPTION, RADIATOR ........................... 7-27
PRESSURE CAP - OPERATION, RADIATOR ........................... 7-27
PRESSURE CAP TESTING - DIAGNOSIS AND TESTING, COOLING SYSTEM ........7-28
PRESSURE FOR HIGH SPEED OPERATION - STANDARD PROCEDURE,
TIRE ............................... 22-17
PRESSURE GAUGE - STANDARD PROCEDURE, FUEL .................... 14-3PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION ..................... 9-85,9-9
PRESSURE MONITORING - DESCRIPTION, TIRE ................... 22-9
PRESSURE MONITORING - OPERATION, TIRE ............................... 22-10
PRESSURE REGULATOR - INSTALLATION, FUEL .................. 14-7
PRESSURE REGULATOR - OPERATION, FUEL ............................... 14-7
PRESSURE REGULATOR - REMOVAL, FUEL ............................... 14-7
PRESSURE RELEASE PROCEDURE - STANDARD PROCEDURE, FUEL
SYSTEM ............................ 14-2
PRESSURE RELIEF VALVE - INSTALLATION, OIL ................... 9-144
PRESSURE RELIEF VALVE - REMOVAL, OIL................................ 9-143
PRESSURE RELIEF VALVE, DESCRIPTION - HIGH ............................. 24-72
PRESSURE RELIEF VALVE, OPERATION - HIGH .............................. 24-72
PRESSURE SENSOR - DESCRIPTION, SEAT WEIGHT BLADDER ...............8O-43
PRESSURE SENSOR - DIAGNOSIS AND TESTING, TIRE ...................... 22-11
PRESSURE SENSOR - OPERATION, SEAT WEIGHT BLADDER ................... 8O-44
PRESSURE, SPECIFICATIONS - FUEL SYSTEM ............................ 14-4
PRESSURE SWITCH - DESCRIPTION, OIL . 9-144
PRESSURE SWITCH - INSTALLATION, OIL ........................... 9-144,9-56
PRESSURE SWITCH - OPERATION, OIL . . . 9-144
PRESSURE SWITCH - REMOVAL, OIL ....9-144,
9-56
PRESSURE TEST - DIAGNOSIS AND TESTING, CYLINDER COMPRESSION . . . 9-85,9-9
PRESSURE TEST - DIAGNOSIS AND TESTING, POWER STEERING SYSTEM
FLOW ............................... 19-1
PRESSURE TESTS - DIAGNOSIS AND TESTING, CLUTCH AIR ...........21-153,21-8
PRESSURE TESTS - DIAGNOSIS AND TESTING, HYDRAULIC ............21-150,21-6
PRESSURE TRANSDUCER - DESCRIPTION, A/C ................... 24-20
PRESSURE TRANSDUCER - OPERATION, A/C................................ 24-20
PRESSURE TRANSDUCER, DIAGNOSIS AND TESTING - A/C ................... 24-21
PRESSURES - STANDARD PROCEDURE, TIRE INFLATION ..................... 22-16
PROGRAMMABLE COMMUNICATIONS INTERFACE (PCI) BUS, OPERATION ......14-25
PROGRAMMING - STANDARD PROCEDURE, PCM/SKIM ................8E-1
PROGRAMMING - STANDARD PROCEDURE, REMOTE KEYLESS
ENTRY TRANSMITTER ................8N-24
PROGRAMMING - STANDARD PROCEDURE, TRANSPONDER ...........8Q-6
PROGRAMMING, STANDARD PROCEDURE - ELECTRONIC VEHICLE
INFORMATION CENTER ................8M-8
PROP ROD - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT .........23-140
PROP ROD - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT .............23-139
PROPORTIONING - DESCRIPTION, ELECTRONIC VARIABLE BRAKE ..........5-88
PROPORTIONING - OPERATION, ELECTRONIC VARIABLE BRAKE ..........5-89
PROPORTIONING VALVE (HEIGHT SENSING) - DESCRIPTION ..............5-53
PROPORTIONING VALVE (HEIGHT SENSING) - DIAGNOSIS AND TESTING .....5-54
PROPORTIONING VALVE (HEIGHT SENSING) - INSTALLATION ..............5-55
PROPORTIONING VALVE (HEIGHT SENSING) - OPERATION ................5-53
PROPORTIONING VALVE (HEIGHT SENSING) - REMOVAL .................5-55
PULLEY - DESCRIPTION, GENERATOR DECOUPLER ........................ 8F-28PULLEY - DIAGNOSIS AND TESTING,
GENERATOR DECOUPLER ..............8F-28
PULLEY - INSTALLATION, GENERATOR DECOUPLER ........................ 8F-29
PULLEY - INSTALLATION, TIMING BELT TENSIONER .......................... 9-70
PULLEY - OPERATION, GENERATOR DECOUPLER ........................ 8F-28
PULLEY - REMOVAL, GENERATOR DECOUPLER ........................ 8F-29
PULLEY - REMOVAL, TIMING BELT TENSIONER .......................... 9-69
PUMP - 2.4L - CLEANING, WATER ........7-32
PUMP - 2.4L - DESCRIPTION, WATER .....7-32
PUMP - 2.4L - INSPECTION, WATER ......7-32
PUMP - 2.4L - INSTALLATION, WATER .....7-32
PUMP - 2.4L - REMOVAL, WATER ........7-32
PUMP - 3.3/3.8L - CLEANING, WATER .....7-35
PUMP - 3.3/3.8L - DESCRIPTION, WATER ............................. 7-34
PUMP - 3.3/3.8L - INSPECTION, WATER . . . 7-35
PUMP - 3.3/3.8L - INSTALLATION, WATER ............................. 7-35
PUMP - 3.3/3.8L - REMOVAL, WATER .....7-34
PUMP - ASSEMBLY, OIL ...........9-146,9-58
PUMP - ASSEMBLY, OIL ........21-112,21-263
PUMP - CLEANING, OIL ...........9-145,9-57
PUMP - DESCRIPTION, FUEL ............14-8
PUMP - DESCRIPTION, FUEL DOSING . . . 24-117
PUMP - DESCRIPTION, OIL .............9-144
PUMP - DESCRIPTION, OIL ......21-110,21-261
PUMP - DISASSEMBLY, OIL ........9-145,9-57
PUMP - DISASSEMBLY, OIL .....21-110,21-261
PUMP - INSPECTION, OIL ..........9-145,9-58
PUMP - INSTALLATION, FUEL DOSING . . . 24-117
PUMP - INSTALLATION, LEAK DETECTION ......................... 25-15
PUMP - INSTALLATION, OIL ........9-146,9-59
PUMP - INSTALLATION, SEAL - OIL ....21-113,
21-264
PUMP - OPERATION, FUEL ..............14-8
PUMP - OPERATION, FUEL DOSING .....24-117
PUMP - OPERATION, OIL .......21-110,21-261
PUMP - REMOVAL, FUEL DOSING ......24-117
PUMP - REMOVAL, LEAK DETECTION ....25-15
PUMP - REMOVAL, OIL ............9-144,9-56
PUMP - REMOVAL, SEAL - OIL . . . 21-113,21-264
PUMP (2.4L ENGINE) - INSTALLATION ....19-43
PUMP (2.4L ENGINE) - REMOVAL .......19-38
PUMP (2.4L/3.3L/3.8L ENGINE) - DESCRIPTION ....................... 19-36
PUMP (3.3L/3.8L ENGINE) - INSTALLATION ....................... 19-43
PUMP (3.3L/3.8L ENGINE) - REMOVAL . . . 19-40
PUMP (DIESEL) - DESCRIPTION .........19-37
PUMP (DIESEL) - INSTALLATION ........19-43
PUMP (DIESEL) - REMOVAL ............19-41
PUMP INITIAL OPERATION - STANDARD PROCEDURE, POWER STEERING ........19-37
PUMP INLET TUBE - 2.4L - DESCRIPTION, WATER .................7-36
PUMP INLET TUBE - 2.4L - INSTALLATION, WATER .................7-36
PUMP INLET TUBE - 2.4L - REMOVAL, WATER ............................. 7-36
PUMP INLET TUBE - 3.3/3.8L - INSTALLATION, WATER .................7-37
PUMP INLET TUBE - 3.3/3.8L - REMOVAL, WATER .................... 7-37
PUMP MODULE - DESCRIPTION, FUEL ....14-8
PUMP MODULE - OPERATION, FUEL ......14-9
PUMP MOTOR - INSTALLATION, WASHER ........................... 8R-12
PUMP MOTOR - REMOVAL, WASHER ....8R-12
PUMP (PULLEY) - ASSEMBLY ..........19-42
PUMP (PULLEY) - DISASSEMBLY ........19-41
PUMP RELAY - DESCRIPTION, FUEL .....14-32
PUMP RELAY - OPERATION, FUEL .......14-32
PUMP, SPECIAL TOOLS - POWER STEERING .......................... 19-44
PUSH-PIN GROMMET REPLACEMENT, STANDARD PROCEDURE ..............8N-48
PUSHRODS - DESCRIPTION ............9-112
PUSHRODS - OPERATION ..............9-112
QUAD BUCKET - INSTALLATION, BUCKET SEAT BACK ........................ 23-141
QUAD BUCKET - INSTALLATION, SEAT BELT BUCKLE - FIRST ROW INBOARD ....8O-36
24 INDEXRS
Description Group-Page Description Group-Page Description Group-Page