Wheel nut Citroen BERLINGO 2005 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 368
AXLES
SUSPENSION
STEERING
C4TIGHTENING TORQUES: POWER-ASSISTED STEERING
Steering column
Ref. Description Tightening
1Fixed central controls steering wheel screw2,2 ± 0,2
2Steering column interface nuts
3Upper nuts
4Lower nuts
5Fixing of steering cardan on valve stem
Steering mechanism with integral ram
Ref. Description Tightening
6Union of hydraulic pipe on ram0,8 ± 0,1
7Fixing of distributor valve on steering mechanism1,5 ± 0,1
8Fixing of bracket on distributor valve2 ± 0,2
9Union of hydraulic pipe on distributor valve0,8 ± 0,1
10Steering ball-joint nut3,5 ± 0,3
11Locking nut for adjustment of steering track rods5,5 ± 0,5
12Fixing of ball-joint on steering rack7 ± 0,7
13Stud on steering mechanism0,8 ± 0,1
14Nut fixing mechanism on subframe8 ± 0,8
B3EP177D
B3EP176D
2,2 ± 0,2
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 368

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
CHECKING THE POWER STEERING ASSISTANCE PRESSURE
Fill the power steering reservoir to the max.mark «a»on the cap (4).
Engine stopped, move the steering slowly from lock to lock, in both directions approx. ten times.
Top up the fluid to the max. mark «a»on the cap (4).
Run the engine at idle for 3 minutes, without any action on the steering wheel.
Move the steering from lock to lock, until there is no longer any tight spot.
Top up the level if it again goes down.
Bleed the circuit by moving the steering several timesin each direction.
Top up the level if it again goes down.
IMPERATIVE: Use new power steering fluid for both filling and topping-up the circuit.
B3EP16HC
374
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 374

Downloaded from www.Manualslib.com manuals search engine 380
AXLES
SUSPENSION
STEERING
XSARA TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).
(1)Damper nut: 4,5 ± 0,4
(2)Cup screw: 2,5 ± 0,3
(3)Suspension leg
(4)Anti-roll bar link rod upper ball-joint: 3,7 ± 0,3
(5)Suspension leg pivot
(hollow pivot): 4,5 ± 0,5
(5)Suspension leg pivot (pivot «H»): 5,5 ± 0,5
(6)Anti-roll bars: 3,7 ± 0,3
(7)Anti-roll bar link rod lower ball-joint
(8)Pivot lower ball-joint: 4 ± 0,4
(9) Driveshaft nut: 32,5 ± 2,5
(10)Wheel bolt: 9 ± 1
(11) Lower arm front mounting: 7,6 ± 0,7
(12)Lower arm rear mounting and anti-roll bar bearing: 6,8 ± 0,6
(13)Screw under rear mounting: 3,1 ± 0,3
(14) Ball-joint fixing on lower arm: 5 ± 0,5
Subframe to bodyshell fixing screw: 8,5 ± 0,8
B3CP040PB3CP041D
Vehicles from RPO 8667# are all
equipped as standard with ventilated
discs.
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 380

Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).(1) Damper nut: 4.5 ± 0.4
(2)Cup screw: 2.5 ± 0.2
(3)Suspension leg
(4)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(5)Suspension leg swivel: 4.5 ± 0.4
(6)Anti-roll bar
(7)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(8)Lower swivel ball-joint: 4 ± 0.4
(9)Hub nut
(greased): 32.5 ± 2
(10)Wheel bolt
(face and threads not greased): 9 ± 1
(11) Lower arm front pivot: 7.6 ± 0.7
(12) Lower arm rear pivot and
anti-roll bar bearing: 6.8 ± 0.6
(13) Screw under rear pivot : 3.5 ± 0.3
Lower arm in forged steel : 3.7 ± 0,3
Lower arm in plate steel: 3.1 ± 0,3
Screw fixing subframe on bodyshell: 8.5 ± 0,8
Screw fixing ball-joint on lower
arm
(plate steel): 4.5 ± 0,4
Anti-roll bar
Engines
ALL TYPESDiameter
21Colour ref.
WHITE Suspension leg angle:
Ta b«a»towards the front.
B3CP056P
B3CP057D
B3CP043D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 393

Downloaded from www.Manualslib.com manuals search engine 394
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: REAR AXLE
Tightening torques (m.daN).
(14)Front silentblock on subframe: 9.4 ± 0.9
(15)Anti-roll bar bolt: 5.5 ± 0.5
(16)Rear torsion bar
(17) Anti-roll bar
(18) Tubular axle
(19)Front silentblock on bodyshell: 4 ± 0.4
(20)Rear upper arm.
(21)Wheel bolt
(face and threads not lubricated): 9 ± 1
(22)Damper
(23)Rear silentblock on subframe: 5.4 ± 0.5
(24)Damper pin nut: 11 ± 1
(25)Stub axle nuts
(lubricated): 25 ± 2
(26)Rear silentblock on bodyshell: 6.5 ± 0.6
Anti-roll bar
Torsion bar
Engines
ALL TYPES 19,6 PINKØ (mm)
Colour ref.Ø (mm)
21Colour ref.
ORANGE
B3DP078D
NOTE: The RH torsion bar can be identified by 1 paint line.
The LH torsion bar can be identified by 2 paint lines.
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 394

Downloaded from www.Manualslib.com manuals search engine 419
BRAKES
PARKING BRAKE
XSARA
Checking and adjusting the handbrake.
Remove the handbrake console.
Jack up and chock the vehicle with the rear wheels hanging free.
Check the correct routing of the brake cables under the vehicle.
Apply and release the handbrake ten times
.
Set the handbrake to the 3rdnotch.
Tighten the nut (1)until the rear brakes are applied.
Pull the handbrake lever vigorously 4to 5 times.
Set the handbrake to the 3rd notch.
Check that the rear brakes are applied.
Check that the wheels can be turned freely by hand with the handbrake
released.
Lower the vehicle.
Refit the handbrake console.
B3FP095D
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 419

Downloaded from www.Manualslib.com manuals search engine 426
BRAKES
B3FP11XD
PARKING BRAKE ADJUSTMENT
XSARA PICASSO
Adjustment.
Remove the handbrake trim (1).
Unclip the sound-deadening (2).
Raise and support the vehicle with the rear wheels hanging
free.
Check the correct routing of the brake cables under the
vehicle.
Apply and release the handbrake 4 times
.
Set the handbrake to the 5thnotch.
Tighten the nut (3)until the rear brakes are applied.
Pull the handbrake lever vigorously 4to 5 times.
Set the handbrake to the 5thnotch.
Check that the rear brakes are applied.
With the handbrake released, check that the wheels can be
turned freely by hand.
Lower the vehicle.
Refit the sound-deadening (2)and the handbrake trim (1).
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 426