Citroen BERLINGO 2005 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 315
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFU - NFU - RFN - RFJ - RFK - 9HX - 9HY - 9HZ - RHR
NOTE:All the clutches are «push»type with hydraulic control.
NOTE:The DV6TED4and DW10BTED4engines are equipped with a double damping flywheel (DVA).
Description.
The declutch control has a declutch fork with a ball-joint on the axis.
(1)The ball-joint is screwed into the clutch casing
(2) Declutch fork
(3)Clutch casing
(4)Bearing
(5) Clutch plate
The clutch control slave cylinder(7)is fixed by two screws (6) into the exterior of the clutch casing.
B2BP047C
B2CP3FAC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 315

Downloaded from www.Manualslib.com manuals search engine 316
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFW - NFU - NFV - 6FZ - RFN - 8HX - 8HZ - 9HY - 9HZ - WJY - RHY - RHZ
NOTE:All the clutches are «push»type with hydraulic control.
Description.
The declutch control has a declutch fork mounted on a ball-joint.
(1)The ball-joint is screwed into the clutch casing
(2)Declutch fork
(3)Clutch casing
(4)Bearing
(5)Clutch plate
The clutch control slave cylinder (7)is fixed by two screws (6)onto the exterior of the clutch casing.
T
ightening torques (m.daN).
Fixing of clutch plate/engine flywheel: 2 ± 0,2.
Fixing of clutch control slave cylinder / clutch housing: 2 ± 0,25.
Fixing of engine flywheel/crankshaft
Pre-tightening: 1,75 ± 0,2.
Angular tightening: 75° ± 5°.
Checking torque: 6,3 ± 2,2.
B2BP047CB2BP05SC
XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 316

Downloaded from www.Manualslib.com manuals search engine 317
CLUTCH
GEARBOX
TRANSMISSION
HYDRAULIC CLUTCH CONTROL: CHECKS AND ADJUSTMENTS
B2BP04XC
IMPERATIVE: Use only new brake brake fluid that is not emulsified, avoid any
ingress of impurities into the hydraulic circuit.
IMPERATIVE: Do not use automatic bleeding equipment
(risk of the brake fluid
emulsifying in the hydraulic circuit).
Couple a transparent tube (5)on the bleed screw, at «c».
Submerge the end of the tube (5)in the recipient containing the brake fluid, located
below the level of the clutch slave cylinder.
Use the transparent tube (5) to act as a siphon, at «b».
WARNING: the end of the tube (5) must be submerged in the brake fluid.
Open the bleed screw at «c».
XSARA PICASSO
Bleeding the hydraulic clutch control
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 317

Downloaded from www.Manualslib.com manuals search engine 318
CLUTCH
GEARBOX
TRANSMISSION
HYDRAULIC CLUTCH CONTROL: CHECKS AND ADJUSTMENTS
Bleeding the hydraulic clutch control
Action the clutch pedal manually through its full travel: 7 timesrapidly down and up.
Allow the clutch pedal to come back up to its high position.
Fill the brake fluid reservoir to the maximum of its capacity.
Open the bleed screw at «c».
Action the clutch pedal manually through its entire travel: 7 times
rapidly down and up.
The last time, keep the clutch pedal fully down.
Reclose the bleed screw, at «c».
If necessary, repeat the operation.
Top up the brake fluid to the MAX.level of the brake fluid reservoir.
Work the clutch vigorously 40 times
.
Start the engine.
Apply the handbrake.
Engage a gear.
Check that the clutch starts to engage at a dimension (X)greater than or equal to 45 mm
(the dimension (X)is
given as a guide).
Repeat the bleed operations if necessary.
C5FP0FQC
XSARA PICASSO
B2BP04YC
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 318

Downloaded from www.Manualslib.com manuals search engine 319
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(1)Gearbox fixings on engine: 4,5 ± 0,5
(2)Reverse gear switch: 2,5 ± 0,2
(3)Drain plug: 3,3 ± 0,3
(4)5th gear housing fixing: 2,2 ± 0,2
(5)Fixing of gearbox housing and clutch housing: 1,9 ± 0,2
B2CP3ZHD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 319

Downloaded from www.Manualslib.com manuals search engine 320
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(6)Clutch bearing guide screw: 1 ± 0,1
(7)Bearing retaining clip screw: 1,8 ± 0,2
Intermediate plate fixing: 5 ± 0,5
Hydraulic clutch slave cylinder fixing: 3 ± 0,3
B2CP3ZJD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 320

Downloaded from www.Manualslib.com manuals search engine 321
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(8)Gearbox support shaft nut: 6,5 ± 0,6
(9) Screws fixing gearbox support on body: 1,9 ± 0,1
(10)Gearbox support plate nut: 2,5 ± 0,2
(11)Nut fixing gearbox support on body: 1,9 ± 0,1
(12)Nut securing rubber bush: 3 ± 0,3
B2CP3ZKC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 321

Downloaded from www.Manualslib.com manuals search engine 322
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX SPECIFICATIONS
Engines: KFW - NFU
Tightening torques (m.daN).
(23) Clutch bearing guide (3 fixing screws): 0,6 ± 0,15
(24)Intermediate plate
(11 fixing screws): 5 ± 0,5
(25)Rear cover
(3 fixing screws): 2,2 ± 0,2
(26)Bearing retaining clip
(4 fixing screws): 1,8 ± 0,2
(27)Secondary shaft nut
(1 nut): 14 ± 1
(28)Gearbox casing
(15 fixing screws): 1,8 ± 0,2
B2CP167P
XSARA
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 322

Downloaded from www.Manualslib.com manuals search engine 323
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX SPECIFICATIONS
Engines: KFW - NFU
Tightening torques (m.daN).
(29) Top-up plug (x1): 2,5 ± 0,5
(30)Drain plug
(x1): 2,5 ± 0,5
(31)Reverse gear switch
(x1): 2,5 ± 0,5
B2CP169D
XSARA
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 323

Downloaded from www.Manualslib.com manuals search engine 324
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: RFN - RFK - 9HX - 9HY - 9HZ
Tightening torques (m.daN).
(1)Air vent hole : 1,5 ± 0,2
(2)Reverse gear rocker switch shaft fixing nut: 4,5 ± 0,2
(3) Differential housing fixing nut: 1,5 ± 0,2
(4)Screw fixing
(Ø M10)differential housing: 5 ± 0,5
(5)Speedometer drive support: 1,5 ± 0,2
(6)Screw fixing
(Ø M7)differential housing: 1,5 ± 0,2
(7)Drain plug : 3,5 ± 0,2
(8)Level plug: 2,2 ± 0,2
(9)Screw fixing gearbox housing/clutch housing: 1,3 ± 0,2
(10) Screw fixing 5th gear housing: 1,5 ± 0,2
(11)Reverse gear switch: 2,5 ± 0,2
B2CP3ZXD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 324