headlamp Citroen BERLINGO MULTISPACE 2016 2.G User Guide

60
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 
With

 
the
 
ignition
 
off,
 
"flash"
 
the
 
headlamps

 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manoeuvres...).
Cornering lighting
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
The
 
function
 
is
 
deactivated
 
temporarily
 
when

 
you
 
use
 
the
 
manual
 
lighting
 
control

 
stalk.
Steering mounted controls

62
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2016
Screenwash and headlamp wash
Pull the stalk towards you, the wash-
wipe   is   accompanied   by   a   timed   sweep  
of

  the   wipers.
The
  headlamp   wash   is   linked   with   the  
wash-wipe, it is triggered if the dipped
headlamps

  are   on.
Turn
  the   ring   past   the   first  
position:

  the   rear   screenwash  
then the rear wiper operates
for

  a   fixed   time.
In winter, in the event of a
considerable
  amount   of   snow  
or ice, switch on the heated
rear

  screen.   Once   the   screen   is  
clear

,   remove   the   snow   or   ice   which  
has

  accumulated   on   the   rear   wiper  
blade.

 
Y
ou   can   then   operate   the   rear  
windscreen

  wiper.
To top up the levels, refer to the
"Levels"
  section   of   chapter   7.
Special position of the
windscreen wipers
In the minute following switching off of the ignition, any action on the
stalk
  positions   the   wipers   against   the  
windscreen

  uprights.
This action enables you to position
the
  wiper   blades   for   winter   parking,  
cleaning

  or   replacement.
Refer to the "Changing a windscreen
wiper
  blade"   section   of   chapter   8.
To
  park   the   wipers   in   their   normal  
position after this has been done,
switch

  on   the   ignition   and   move   the  
stalk. T

urn   the   ring   to   the   first  
position.
Rear wiperRear screenwash
Steering mounted controls

158
Berlingo-2-VP_en_Chap07_Verification_ed01-2016
Levels
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).

181
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
2. Sidelamps
Type A, W5W - 5W
- 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-
 
Remove
  the   bulb   holder   fitted   by  
pressure

  by   pulling   the   connector.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
Front lamps
1. Dipped / Main beam headlamps
T ype C, H4 - 55W
-
 
Remove
  the   centre   cover   by   pulling  
the

  flexible   rubber   tab.
-
 
Disconnect
  the   electrical   connector.
-
 
Release
  the   retaining   tab.
-
 
Change
  the   bulb   taking   care  
to

  align   the   metal   part   with   the  
grooves

  on   the   lamp.
-
 
Reposition
  the   retaining   tab.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
High pressure washing Open

 
the
 
bonnet.
 
T

o
 
access
 
the
 
bulbs,
 
reach

 
behind
 
the
 
headlamp
 
unit.
Carry out the operations in reverse
order
 
to
 
refit
 
each
 
bulb
 
and
 
check
 
that
 
the

 
bonnet
 
is
 
closed
 
securely.
Halogen
 
bulbs
 
must
 
be
 
changed
 
with

 
the
 
headlamp
 
off.
 
Wait
 
a
 
few
 
minutes

 
(risk
 
of
 
serious
 
burns).
 
d
o not touch the bulb directly with your
fingers,
 
use
 
lint-free
 
cloths.
It
 
is
 
normal
 
for
 
condensation
 
to
 
form
 
inside

 
the
 
headlamps.
 
Regular
 
use
 
of
 the
 
vehicle
 
eliminates
 
this
 
misting.
The
 
bulbs
 
must
 
be
 
changed
 
with
 
the ignition of

f or with the battery
disconnected.
 
Wait
 
approximately
 
3 minutes

 
after
 
changing
 
the
 
bulb
 
before

 
reconnecting
 
the
 
battery.
Check
 
that
 
the
 
lamps
 
operate
 
correctly
 
after

 
each
 
operation.
When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
lamps
 
and
 
their
 
edges

 
to
 
avoid
 
damaging
 
their
 
coating
 
and

 
seals.
QUICk HELP
8
Changing a bulb

184
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time   is  
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
on
 
bulbs,
 
refer
 
to
 the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B,
 
PY21W
 
-
 
21W
 
(amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
Changing a bulb

187
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Dashboard fuses
Tilt the cover to gain access to the
fuses.Fuses
F Amperes  Aa
llocation
1 15 Rear wiper
2 -
n

ot used
3 5
a

irbag
4 10 Air
  conditioning,   diagnostic   socket,   mirror   control,  
headlamp

  beam
5 30 Electric windows
6 30 Locks
7 5Rear
  courtesy   lamp,   front   map   reading   lamp,   roof  
console
8 20 Audio

  equipment,   screen,   tyre   under-inflation  
detection,

  alarm   and   siren
9 30Front
  and   rear   12V   socket
10 15 Central
  column
11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument
  panel
14 15 Parking
  sensors,   digital   air   conditioning   controls,  
hands-free

  phone   kit
15 30 Locks
16 -
n

ot used
17 40Rear
  screen/mirrors   demist/defrost
QUICk HELP
8
Changing a fuse

189
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2016
Fuses under the bonnet
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  Aa
llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
  motor
9 10Headlamp
  beam   motor,   fleet   management   unit
10 30 Engine
  components
11 40
n

ot used
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10 Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
QUICk HELP
8
Changing a fuse