ad blue Citroen BERLINGO MULTISPACE RHD 2014.5 2.G User Guide

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
150
range indicators
When switching on the ignition, an
indicator  gives   an   estimate   of   the  
distance that can be travelled with
your vehicle before engine starting
is

  automatically   prevented,   once   the  
vehicle starts using the reserve of a

dBlue
® or after a fault is detected with
the
 
SCR   system.
In
 
the
 
event   of   simultaneous   system  
fault and low a

dBlue
® level, the
shortest
 
range
 
is
 
the
 
one   displayed.
In the event of the risk
of non-starting related to a lack
of AdBlue
®
The engine start prevention
system   required   by   regulations   is  
activated

  automatically   once   the  
a
dBlue
® tank is empty.
range greater than 1 500 miles (2 400 km)
When the ignition is switched on, no
information   on   range   is   displayed  
automatically

  in   the   instrument   panel.
Pressing this button
displays the driving range
temporarily.
Above
  3   000   miles  
(5
  000   km),   the   value   is  
not

  specified. When switching on the ignition, the
UREA warning
  lamp   comes   on,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.:   "Top   up  
emissions

  additive:   Starting   prevented  
in

  900   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed

  every   150   miles   (300   km)  
until

  the   additive   tank   has   been  
topped-up.
Go

  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
r

emaining range between 350 and
1500 miles (600 and 2 400 km)
adBlue® additive

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
151
When switching on the ignition, the
SERVICE  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.   "Top   up  
emissions

  additive:   Starting   prevented  
in

  350   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed every 30 seconds until the
additive

  tank   has   been   topped-up.
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
o

therwise you will not be able to
restart
 
your
 
engine. When switching on the ignition, the
SERVICE
  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal  
and

  the   display   of   the   message  
"T

op   up   emissions   additive:   Starting  
prevented".
The

a dBlue
® tank is empty: the system required
 
by
 
regulations   prevents  
engine

 
starting. To be able to start the engine,
we
  recommend   that   you   call   on  
a

  CITROËN   dealer   or   a   qualified  
workshop

  for   the   top-up   required.   If  
you carry out the top-up yourself, it is
essential

  to   add   at   least   3.8   litres   of  
a dBlue
® to the tank.
r

emaining range between 0 and
350 miles (0 and 600 km) Breakdown related to a lack of
AdBlue
® additive
Refer   to   the   "Topping-up"   section.
adBlue® additive
CHECkS
7

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
152
In the event of a fault with
the the Scr emissions control
system
When switching on the ignition, the
URE
a , SERVICE and diagnostic
warning
  lamps   comes   on,   accompanied
 by an audible signal and the display of


a
  message   "Emissions   fault"   to   signal   a
 fault

  with   the   emissions   control   system.
If
  it   is   a   temporary   fault,   the   alert  
disappears once the exhaust gas
emissions

  return   to   normal.during an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
A  system   that   prevents   engine  starting
  is   activated   automatically  
from

  650   miles   (1   100   km)   after  
confirmation

  of   a   fault   with   the   SCR  
emissions

  control   system.   Have   the  
system

  checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop   as   soon   as  
possible. In the event of the detection


of a fault
If   a   fault   with   the   SCR   system   is  
confirmed

  (after   30   miles   (50   km)  
covered

  with   the   permanent   display   of  
the

  message   signalling   a   fault),   when  
switching on the ignition, the SER

VICE
and
  engine   diagnostic   warning   lamps  
come

  on   and   the   UREA
 
warning   lamp  
flashes,

  accompanied   by   an   audible  
signal

  and   the   display   of   a   message  
(e.g.:

  "Emissions   fault:   Starting  
prevented

  in   150   miles")   indicating   the  
remaining

  range   express   in   miles   or  
kilometres.
While

  driving,   the   message   is  
displayed every 30 seconds while the
fault

  with   the   SCR   system   persists.
You should go to a CITR
o Ë n dealer
or
  a   qualified   workshop   as   soon   as  
possible.
o

therwise, you will not be able to
restart
  your   engine.
adBlue® additive

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
153
Every time the ignition is switched on, the SERVICE and engine diagnostic
warning
  lamps   come   on   and   the   UREA
 warning

  lamp   flashes,   accompanied  
by an audible signal and the display of
the

  message   "Emissions   fault:   Starting  
prevented".
Y

ou have exceeded the authorised
driving
  limit:   the   starting  
prevention

  system   inhibits   engine  
starting.
T

o be able to start the engine, you
must
  call   on   a   CITROËN   dealer   or   a  
qualified

  workshop.
Starting prevented
The a dBlue
® additive freezes at
temperatures   below   around   -11°C.
The
 
SCR
 
system   includes   a   heater   for  
the

a
dBlue
® tank.
In
 
exceptional   circumstances   (vehicle  
kept

 
for
 
a
 
long   period   at   temperatures  
that

 
are
 
constantly   below   -15°C),   an  
emissions

 
control   system   fault   alert  
may

 
be
 
related   to   freezing   of   the  
a
dBlue
® in your vehicle.
Park
 
your   vehicle   in   a   warmer   area   for  
a

 
few
 
hours   until   the   additive   becomes  
liquid

 
again.
The
 
emissions   alert   does   not   go   off  
immediately

,   it   will   occur   after   several  
mile

 
of
 
running.
Freezing of the AdBlue
® additive
adBlue® additive
CHECkS
7

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
154
topping-up the AdBlue® additive
Filling the adBlue® tank is an operation included in every routine service on
your vehicle by a CITR
o Ë n dealer
or
 
a
 
qualified
 
workshop.
n

evertheless, given the capacity
of
 
the
 
tank,
 
it
 
may
  be   necessary   to  
top-up the additive between services,
more

 
particularly
 
if   an   alert   (warning  
lamps

 
and
 
a
 
message)   signals   the  
requirement.
Y

ou can got to a CITR o Ë n dealer
or
 
a
 
qualified
 
workshop.
If you envisage topping-up yourself,
please read the following warnings
carefully. Precautions in use
The
a dBlue® additive is an urea-based
solution.
 This   liquid   is   non-flammable,  
colourless

 
and   odourless   (kept   in   a  
cool

 
area).
In
 
the
 
event
 
of   contact   with   the   skin,  
wash the af

fected area with soap and
water.
 
In
 
the
  event   of   contact   with   the  
eyes, wash (irrigate) the eyes with
large

 
amounts   of   water   or   with   an   eye  
wash

 
solution   for   at   least   15   minutes.  
If a burning sensation or irritation
persists,

 
get
  medical   attention.
If
 
swallowed,   immediately   wash   out   the  
mouth

 
with
 
clean   water   and   then   drink  
plenty

 
of
 
water.
In
 
certain
 
conditions   (high   ambient  
temperature,

  for   example),   the   risk  
of

 
release
 
of
  ammonia   cannot   be  
excluded:

 
do   not   inhale   the   product.  
Ammonia

 
vapour   has   en   irritant   effect  
on

 
mucous
 
membranes   (eyes,   nose  
and

 
throat).
k

eep
a
dBlue
® out of the reach of
children,
 
in
 
its
  original   bottle.
n

ever transfer
a
dBlue
® to another
container:
 
it
 
would
 
loose   its   purity. Use only
a dBlue
® additive that meets the
 
ISO
 
22241
 
standard.
n

ever dilute the additive with
water.
n

ever pour the additive into the d iesel
fuel
 
tank.
The supply in a non-drip bottle
simplifies
 
toping-up.  
Y
ou   can   obtain  
1.89

 
litre
 
(half
 
a
 
US   gallon)   bottles  
from

 
a
 
CITROËN dealer   or   a   qualified  
workshop.Never

 
top-up   from   an  
AdBlue®
dispenser reserved for heavy
goods
 
vehicles.
adBlue® additive

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
155
recommendations on storage
a
dBlue® freezes at about -11°C and
 
deteriorates   above   25°C.   It   is  
recommended

  that   bottles   be   stored   in  
a

 
cool
 
area   and   protected   from   direct  
sunlight.
Under these conditions, the additive
can

 
be
 
kept   for   at   least   a   year.
If the additive has frozen, can be used
once
 
it
 
has   completely   thawed   out.
n

ever store bottles of
a
dBlue
® in
your
 
vehicle. Procedure
Before topping-up, ensure that the
vehicle
  is   parked   on   a   flat   and   level  
surface.
In wintry conditions, ensure that
the

  temperature   of   the   vehicle   is  
above -1

1°C.   Otherwise,   by   freezing,  
the

a dBlue
® cannot be poured into its
tank.
 
Park
 
your   vehicle   in   a   warmer  
area for a few hours to allow the top-up
to

 
be
 
carried   out.
F
 
Switch

 
off   the   ignition   and   remove  
the

 
key. -

For access to the a
dBlue
® tank, open
 
the
 
filler
 
flap;
 
the
 AdBlue® filler cap is located to the left of the fuel
filler
 
cap
-
 
T

urn
 
the
 
blue
 
cap
 
a
 
6
th of a turn
anti-clockwise.
-
 
Lift

 
off
 
the
 
blue
 
cap.
adBlue® additive
CHECkS
7

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
156
- obtain a bottle of adBlue®. After first
 
checking
 
the
 
use-by
 
date,  
read carefully the instructions on
use on the label before pouring
the contents of the bottle into your
vehicle's

a
dBlue
® tank.
Important
:
 
if
 
your   vehicle's
 
a

dBlue
® tank is completely 
empty
 
-
 
which   is   confirmed   by   the alert

 
messages   and   the   impossibility
 of

 
starting
 
the   engine,   you   must   add   at
 least

 
3.8
 
litres   (so   two   1.89   litre bottles). -
 
After
  emptying   the   bottle,   wipe  
away

  any   spillage   around   the   tank  
filler

  using   a   damp   cloth.
If any additive is split or splashed,
wash   immediately   with   cold   water  
or

  wipe   with   a   damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.
-  
Refit
  the   blue   cap   to   the   tank   and  
turn

  it   a   6
th of a turn clockwise, to its stop.
-
 
Close

 
the
 
filler   flap.
n
ever dispose of
a
dBlue
® additive
bottles
 
in
 
the
 
household
 
waste.  
Place

 
them
 
in
 
a
 
special
 
container  
provided

 
this
 
purpose
 
or
 
take
 
them   to  
your

 
dealer.
Important:
 
in the event of a top-
up after a breakdown because
of a lack of additive, signalled
by
 
the
 
message
 
"Top
 
up
 
emissions  
additive:

 
Starting
 
prevented",
 
you   must  
wait

 
around
 
5
 
minutes
 
before
 
switching  
on the ignition,

without opening the
driver's door, locking the vehicle or
introducing the key into the ignition
switch.
Switch on the ignition, then, after
10
 
seconds,
 
start
 
the
 
engine.
adBlue® additive

10.3
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
The system is protected in such a way that it will only operate  in   your   vehicle.
eMyWay
01 First steps - c ontrol panel
For safety reasons, the driver must carry out operations which
  require   prolonged   attention   while   the   vehicle   is  
stationary

.
When the engine is switched off and to prevent
discharging
  of   the   battery,   the   system   switches   off  
following

  the   activation   of   the   energy   economy   mode.
cOntEntS
02
Steering mounted
controls
03

General operation
04

n avigation - Guidance
05
t
raffic information
06

u sing the telephone
07
r adio
08

Music media players
09


Audio
settings
10
c onfiguration
11
t
rip
computer p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
10.4
10.6
10.7
10.9
10.22
10.25
10.35
10.38
10.44
10.45
10.47
Satellite navigation system
Multimedia audio system
Bluetooth
® telephone
12

Screen menu
map
Frequently asked questions p.
p.
10.48
10.52

05
10.24
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
Principal tM c symbols
Red and yellow triangle: traffic information, for example:
Black   and   blue   triangle:   general   information,   for   example:
Weather reports
Modified
  signage
Risk
  of   explosion Traffic
  reports
n

arrow carriageway
Road closed
Wind
Slippery surface
Demonstration Fog
a

ccident
d

anger
Parking
d

elay
n

o entry Snow
  /   ice
Roadworks
Traffic
  jam
receiving tA messages
The TA (Traffic  Announcement)   function   gives   priority   to  T A  alert  messages.
 T o   operate,   this   function   needs   good   reception   of   a  
radio

  station   transmitting   this   type   of   message.   When   a   traffic   report  
is

  transmitted,   the   current   audio   source   (Radio,   CD,   USB,   ...)   is  
interrupted

  automatically   to   play   the  
T
A
 
message.   Normal   playback  
of

  the   audio   source   resumes   at   the   end   of   the   transmission   of   the  
message.Press

r A d IO   to   display   the   menu.
Select "Service announcements" then
confirm.
a

ctivate or deactivate " t A"
  then   confirm.
The
  volume   setting   for  
T
A
 
messages   can   be   adjusted   only   during   the  
transmission

  of   this   type   of   alert.
Activate
  or   deactivate   the   function   at   any   time   by   pressing  
the

  button.
During
  a   message,   press   the   button   to   interrupt   it.
trAFFIc InFOrMAtIO n

06
10.25
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
Access to the "tELEPHOnE" menu
"telephone"
" d ial"
"
d irectory of contacts"
"ontacts management "
"Phone functions "
"Bluetooth functions "
"Hang up "
Go
  from   the   list   to   the   menu   (left/right).
or
List of recent calls sent and
received with the telephone
connected
 
to
 
the
 
system.
Press
 
this
 
button.
To
 
make
 
a
 
call,
 
select
 
a
 
number
 
in
 
the
 
list
 
and
 
confirm
 
" OK"
to
 
start
 
the
 
call.
Connecting a different telephone deletes the list of
recent
 
calls. No
  telephone   connected.
Telephone
  connected.
Incoming
  call.
Outgoing
  call.
Synchronisation of
contacts
  in   progress.
Telephone call in
progress.
In the top bar of the permanent
display
uSInG tHE tELEPHOnE