ABS Citroen C CROSSER 2008 1.G Owner's Manual

I N S T R U M E N T S a n d C O N T R O L S
I
19

1. Speedometer.

2. Left-hand direction indicator and
hazard warning lights indicator
light.

3. Main beam headlamps indicator
light.

4. Diesel pre-heating indicator light.

5. Side lights indicator light.

6. Front fog lamps indicator light.

7. Seat belt not fastened / unfastened
warning light.
DIESEL MANUAL GEARBOX INSTRUMENT PANEL

18. Instrument panel display:
- Warning and status displays.
- Total and trip distance recorders.
- Service indicator.
- Coolant temperature.
- Displaying of the trip computer information.
- Cruise control reference value.
- Fascia lighting and parameter settings.
- Fuel level.
- Exterior temperature.
- Transmission mode.

8. Rear fog lamps indicator light.

9. Anti-lock braking system (ABS)
warning light.

10. Battery charge fault warning light.

11. Handbrake applied and brake fl uid
level warning light.

12. Cruise control mode indicator light.

13. Air bags warning light.

14. Engine management warning light.

15. Indicator light for right-hand
direction indicator,
Hazard warning lights indicator
light.

16. Rev counter.

17. Fascia lighting rheostat.
Panel grouping together the dials and
warning/indicator lights. These inform
the driver of the activation of a system
(operation or deactivation indicator
lights) or of the occurrence of a fault
(warning lights).

I N S T R U M E N T S a n d C O N T R O L S
I
22

Warning lights is on Cause Solution - action
Driver’s
seat belt not fastened Fixed The driver has not
fastened or has
unfastened his seat belt. This is accompanied by a message on the
instrument panel display.
Fasten the driver’s seat belt.
ABS
Fixed This comes on if an
anti-lock braking system
failure occurs. It is accompanied by a message on the
instrument panel display. The vehicle retains
conventional braking without assistance but
you are advised to stop. Have it checked by a
CITROËN dealer.
Air bags and
pretensioners Fixed This comes on for a
few seconds when the
ignition is turned to “ON”
then switches off.
It should switch off when the engine is started. If
it does not switch off, contact a CITROËN dealer.
This comes on if an air
bag or pretensioner
failure occurs. It is accompanied by a message on the
instrument panel display. Have the system
checked by a CITROËN dealer without delay.

I N S T R U M E N T S a n d C O N T R O L S
I
24
Warning messages (ignition at “ON”)
Message is on
Associated
warning light
Cause Solution - action Observations
ABS
Fixed
Anti-lock braking
system (ABS)
fault. Consult a CITROËN
dealer. The vehicle retains
conventional braking
without assistance
but you are advised
to stop.
Braking
system Fixed
and The level of
brake fl uid in the
reservoir is too
low.
Stop and top up,
otherwise contact a
CITROËN dealer. If the message
remains on after
topping up, contact a
CITROËN dealer.
Braking system
fault. Consult a CITROËN
dealer.
It is essential
to stop.
Handbrake on
Fixed
You have moved
off with the
handbrake still
applied.
Release the handbrake.

Coolant
temperature Flashing -
High engine
temperature. If the message
fl ashes ,
wait for the engine to
cool before topping up
the level, if necessary.
It is essential to
stop your vehicle in
a safe place.
Flashing If the message
fl ashes
and the service
warning light comes
on , contact a CITROËN
dealer without delay.
Seat belt
Fixed
The driver has
not fastened or
has unfastened
his seat belt.
Fasten your seat belt. An intermittent
audible signal is
heard above 5 mph
(8 km/h).

C H I L D S A F E T Y
V
98
ADVICE ON CHILD SEATS
The incorrect installation of a
child seat in a vehicle compromises
the child’s protection in the event of an
accident.
Remember to fasten the seat belts or
the child seat harnesses keeping the
slack in relation to the child’s body to a
minimum, even for short journeys.
For optimum installation of the “for-
ward facing” child seat, ensure that
the back of the child seat is in contact
with the back of the vehicle’s seat and
that the head restraint does not cause
any discomfort.
If the head restraint has to be re-
moved, ensure that it is stored or at-
tached securely to prevent it from be-
ing thrown around the vehicle in the
event of sharp braking.
Children under the age of 10 must not
travel in the “forward facing” position
on the front passenger seat, unless
the rear seats are already occupied by
other children, cannot be used or are
absent.
Disarm the passenger air bag when
a “rear facing” child seat is installed
on the front seat. Otherwise, the child
would risk being seriously injured or
killed if the air bag were to infl ate. Installing a booster seat
The chest part of the seat belt must
be positioned on the child’s shoulder
without touching the neck.
Ensure that the lap part of the seat
belt passes correctly over the child’s
thighs.
CITROËN recommends the use of
a booster seat which has a back, fi t-
ted with a seat belt guide at shoulder
level.
As a safety precaution, do not leave:
- one or more children alone and un-
supervised in a vehicle,
- a child or an animal in a vehicle which is exposed to the sun, with
the windows closed,
- the keys within reach of children inside the vehicle.
To prevent accidental opening of the
doors, use the “Child lock”.
Take care not to open the rear win-
dows by more than one third.
To protect young children from the
rays of the sun, fi t side blinds on the
rear windows.

 Lower the control A to position 1 .
Locking
Unlocking

 Raise the control A to position
2 .
Mechanical system to prevent opening
of the rear door using its interior con-
trol.
The control is located on the edge of
each rear door.

S A F E T Y
100
BRAKING ASSISTANCE
SYSTEMS
Group of supplementary systems which
help you to obtain optimum braking
in complete safety in emergency
situations:
- the anti-lock braking system (ABS),
- the electronic brake force distribution (EBFD).
When braking in an emergen-
cy, press very fi rmly without re-
leasing the pressure. The two warning lights comes on at
the same time and the two warnings
are displayed alternately on the
instrument panel display.
When replacing wheels (tyres and
rims), ensure that they conform to the
manufacturer’s recommendations.
Operating fault
If this warning light comes on,
accompanied by the indication on the
instrument panel display, it indicates
a malfunction of the anti-lock braking
system which could result in a loss of
control of the vehicle when braking.
Consult a CITROËN dealer.
If these two warning lights come
on, linked with the warnings on the
instrument panel display, they indicate a
malfunction of the electronic brake force
distribution which could result in a loss of
control of the vehicle on braking.

You MUST stop as soon as it is safe
to do so.
Consult a CITROËN dealer.
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the sta-
bility and manoeuvrability of your vehi-
cle when braking, in particular on poor
or slippery surfaces. The warning light comes on for a few
seconds when the ignition is switched
on (ON position). If it does not switch
off or does not come on, contact a
CITROËN dealer.
When the vehicle is stationary
When the vehicle is moving
If this warning light comes
on continuously it indicates
a malfunction of the anti-lock
braking system which could
result in a loss of control of the vehicle
on braking.

You MUST stop as soon as it is safe
to do so.
Consult a CITROËN dealer.
Activation
The anti-lock braking system is active if
the vehicle speed is higher than 6 mph
(10 km/h). It is deactivated when the ve-
hicle speed falls below 3 mph (5 km/h).
The anti-lock braking system comes
into operation automatically when there
is a risk of wheel lock.
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal.

P R A C T I C A L I N F O R M A T I O N
IX
139
Fascia fuses
The fuse boxes are placed in the lower
part of the fascia behind the glove box.
Access to the fuses

 Open the glove box,

 Push the two opening guides C inwards to
pass the fi rst notch,

 Remove the retaining tab D pulling it outwards,

 Support the cover and tilt it downwards,

 Change the fuse (refer to the corresponding
paragraph).

Fuse N° Rating Functions

1 *
30 A Heating.

2 15 A Brake lights, third brake light, built-in systems
interface.

3 10 A Rear fog lamps.

4 30 A Windscreen wipers and wash-wipe.

5 10 A Diagnostic socket.

6 20 A Central locking, exterior mirrors.

7 15 A Audio equipment, telematics, multifunction display,
hands-free kit, rear DVD player.

8 7.5 A Remote control key, air conditioning control unit,
instrument panel, controls bar, steering wheel
controls.

9 15 A Multifunction display, instrument panel.

10 15 A Built-in systems interface.

11 15 A Rear wiper.

12 7.5 A Instrument panel, 4 wheel drive control unit,
air conditioning control panel, ABS control
unit, multifunction display, automatic headlamp
adjustment, heated seats, air bags control unit,
steering wheel angle sensor, sunroof, rear screen
demisting, remote control.

13 - Not used.

14 10 A Ignition switch.

15 20 A Sunroof.

16 10 A Exterior mirrors, audio equipment, telematics, rear
DVD player.

P R A C T I C A L I N F O R M A T I O N
IX
142
Spare fuses
The spare fuses are located under the engine compartment
fuse box cover. The cover does not contain spare fuses with an amper-
age of 7.5 A, 25 A or 30 A. If one of the fuses with these
amperages develops a fault, replace it with the following
fuse:
A 7.5 A fuse must be replaced with the
10 A spare fuse ,
a
25 A fuse with a
20 A spare fuse and a
30 A fuse with
the audio system fuse (N° 31) .
* The maxi-fuses provide additional protection for the el
ectrical systems. All work on the maxi-fuses must be carried
out by a CITRÖEN dealer.

Fuse N° Rating
Functions

22 20 A Engine control unit, water in diesel detector, injection
pump (Diesel), air fl ow sensor, water
presence sensors, oxygen sensor, camshaft position sensor, purge canist er solenoid valve,
vehicle speed sensor, variable timing (VTC) solenoid valve, EGR so lenoid valve.

23 15 A Petrol pump, fuel gauge.

24 *
30 A Starter.

25 - Not used.

26 *
40 A ABS control unit, ASC control unit.

27* 30 A ABS control unit, ASC control unit.

28 *
30 A Condenser fan.

29 *
40 A Radiator fan.

30 30 A Passenger compartment fuse box.

31 30 A Audio amplifi er.

32 30 A Diesel engine control unit.

Fuse N° Rating

33 10 A

34 15 A

35 20 A

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
164
When play begins, “READING” appears
on the display then disappears to make
way for the folder number, the track
number, the playing time and “MP3”.
Playing the beginning of each track
Press the “SCAN” button
to start playing the fi rst ten
seconds of each track in all of
the folders. “SCAN” appears
on the display and the corresponding
track number fl ashes.
To exit this mode, press this button
again.
MP3 / Tag ID3 display
Press the “DISP” button
several times in succession;
the MP3 information appears
in the following order:
FOLDER NAME / TRACK NAME /
NORMAL DISPLAY MODE. If the information exceeds
12 characters, press the
“PAGE” button to see the
rest.
In the absence of MP3 or Tag ID3
information to be displayed, “NOTITLE”
appears on the display.
Press the “DISP” button
for more than two seconds
to activate the Tag ID3
information. “TAG” appears
on the display.
Press the “DISP” button several times
in succession; the Tag ID3 information
appears in the following order:
ALBUM NAME / TRACK NAME /
ARTIST NAME / NORMAL DISPLAY
MODE. To deactivate this information, press
the “DISP” button again for more than
two seconds.
Repeating the tracks in a folder
Press the “RPT” button for
more than two seconds to
repeat the playing of the
tracks contained in the
current folder. “D-RPT” appears on the
display.
To exit this mode, press this button
again.
Random playing of a folder
Press the “RDM” button to
start random playing of the
tracks in the current folder.
“RDM” appears on the
display.
To exit this mode, press this
button again.
Random playing of a disc Press the “RDM” button for
more than two seconds to
start random playing of the
tracks in all of the folders.
“D-RDM” appears on the
display.
To exit this mode, press this
button again. On CD-R/RWs, the quality of the
playing sound depends on the
encoding software, the burning
device and the burning speed used.
Depending on the fl ow chart of the
MP3 folders and fi les on the disc,
play may not begin immediately.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
209
Matching your Bluetooth®

telephone
The system can register up to 7 Blue-
tooth ®
compatible mobile telephones.
The telephone which has the
highest level of priority is matched
automatically.
It is absolutely essential that the vehicle
is parked in a safe place with the
handbrake applied.
1 - Press the SPEAK button. 7 - Say a 4-digit number which
will be recorded as the match-
ing code. 12 - After the audible signal,
allocate a name to the
telephone by saying the
name of your choice.
13 - The system says “Allocate an order of priority between 1 and 7. One is
the highest level of priority”.
If the system does not detect the
Bluetooth ®
compatible mobile
telephone, the matching process
stops accompanied by an audible
signal.
If you select a level of priority which
has already been allocated to
another telephone, the system asks
you if you wish to replace this level
of priority.
You can choose any 4-digit number.
Remember this matching code as
you must enter it in the telephone
in one of the following steps of the
matching procedure.
9 - The system says “Start the matching procedure on the telephone. Consult
the instructions in the telephone
manual”.
2 - Say “Confi gure”.
3 - Say “Matching options”.
5 - Say “Match a telephone”. 8 - The system confi rms the
validity of the number spoken,
answer “Yes”. Say “No” to
return to step 7.
10 - Consult your mobile telephone’s user manual
and enter the matching
code recorded in step 7
in the telephone.
11 - When it detects a Bluetooth ®

compatible mobile telephone, the
system says “Please say the name
of the telephone after the bleep”. 14 - Say a number between 1
and 7 to establish the level
of priority of the mobile
telephone.
15 - The system says and confi rms the and the
of its priority.
16 - Answer “Yes” or say “No” to return to step 13.
17 - The systems says “Matching complete” then
emits an audible signal
and deactivates the voice
recognition.
4 - The system says “Do you wish to match a telephone, delete a
telephone or obtain the list of
matched telephones?”.
6 - The systems says “Please say the 4 digits of a matching code”.