ignition CITROEN C CROSSER 2010 Owner's Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010, Model line: C CROSSER, Model: CITROEN C CROSSER 2010Pages: 217, PDF Size: 6.48 MB
Page 100 of 217
VI
!
S A F E T Y
1 0 5
AIRBAGS
The airbags do not operate
when the ignition is switched
off.
T h i s e q u i p m e n t w i l l o n l y o p e r a t e
o n c e . I f a s e c o n d i m p a c t o c c u r s
( d u r i n g t h e s a m e o r a s u b s e q u e n t
a c c i d e n t ) , t h e a i r b a g w i l l n o t o p e r a t e .
Front airbags
S y s t e m w h i c h p r o t e c t s t h e h e a d a n d
c h e s t o f t h e d r i v e r a n d f r o n t p a s s e n g e r
i n t h e e v e n t o f a f r o n t i m p a c t .
T h e d r i v e r ' s a i r b a g i s fi t t e d i n t h e c e n t r e
of the steering wheel; the front passen-
g e r ' s a i r b a g i s fi t t e d i n t h e d a s h b o a r d
above the glove box.
Activation
T h e a i r b a g s a r e t r i g g e r e d s i m u l t a n e -
o u s l y , u n l e s s t h e p a s s e n g e r ' s f r o n t a i r
b a g i s d e a c t i v a t e d , i n t h e e v e n t o f a s e -
r i o u s f r o n t i m p a c t a p p l i e d t o a l l o r p a r t
o f t h e f r o n t i m p a c t z o n e A , i n t h e l o n -
g i t u d i n a l c e n t r e l i n e o f t h e v e h i c l e o n a
h o r i z o n t a l p l a n e a n d d i r e c t e d f r o m t h e
front to the rear of the vehicle.
T h e f r o n t a i r b a g i n fl a t e s b e t w e e n t h e
f r o n t o c c u p a n t o f t h e v e h i c l e a n d t h e
d a s h b o a r d t o c u s h i o n t h e i r f o r w a r d
m o v e m e n t .
Impact detection zones
A. F r o n t i m p a c t z o n e .
B. S i d e i m p a c t z o n e .
T r i g g e r i n g o f t h e a i r b a g ( s ) i s a c c o m -
p a n i e d b y a s l i g h t e m i s s i o n o f h a r m -
l e s s s m o k e a n d a n o i s e , d u e t o t h e
a c t i v a t i o n o f t h e p y r o t e c h n i c c a r t r i d g e
i n c o r p o r a t e d i n t h e s y s t e m .
T h i s s m o k e i s n o t h a r m f u l , b u t s e n s i -
t i v e i n d i v i d u a l s m a y e x p e r i e n c e s l i g h t
irritation.
T h e n o i s e o f t h e d e t o n a t i o n m a y r e -
s u l t i n a s l i g h t l o s s o f h e a r i n g f o r a
s h o r t t i m e .
S y s t e m d e s i g n e d t o m a x i m i s e t h e s a f e t y
o f t h e o c c u p a n t s ( w i t h t h e e x c e p t i o n o f
t h e r e a r c e n t r e p a s s e n g e r ) i n t h e e v e n t
o f v i o l e n t c o l l i s i o n s . I t s u p p l e m e n t s t h e
a c t i o n o f t h e f o r c e - l i m i t i n g s e a t b e l t s .
I f a c o l l i s i o n o c c u r s , t h e e l e c t r o n i c
d e t e c t o r s r e c o r d a n d a n a l y s e t h e f r o n t
a n d s i d e i m p a c t s s u s t a i n e d i n t h e i m -
p a c t d e t e c t i o n z o n e s :
- i n t h e c a s e o f a s e r i o u s i m p a c t , t h e
a i r b a g s a r e t r i g g e r e d i n s t a n t l y a n d
p r o t e c t t h e o c c u p a n t s o f t h e v e h i c l e
( w i t h t h e e x c e p t i o n o f t h e r e a r c e n -
t r e p a s s e n g e r ) ; i m m e d i a t e l y a f t e r t h e
i m p a c t , t h e a i r b a g s d e fl a t e r a p i d l y s o
t h a t t h e y d o n o t h i n d e r v i s i b i l i t y o r t h e
e x i t o f t h e o c c u p a n t s ,
- i n t h e c a s e o f a m i n o r o r r e a r i m p a c t o r i n c e r t a i n r o l l - o v e r c o n d i t i o n s , t h e
a i r b a g s w i l l n o t b e t r i g g e r e d ; t h e
s e a t b e l t a l o n e i s s u f fi c i e n t t o p r o -
v i d e o p t i m u m p r o t e c t i o n i n t h e s e
s i t u a t i o n s .
Page 101 of 217
VI
!
!
S A F E T Y
1 0 6
I f t h e a i r b a g w a r n i n g l a m p a n d
t h e d i s p l a y c o m e o n c o n t i n u -
o u s l y , d o n o t i n s t a l l a " r e a r f a c -
i n g " c h i l d s e a t o n t h e f r o n t p a s s e n g e r
seat.
C o n s u l t a C I T R O Ë N d e a l e r .
Operating fault
I f t h i s w a r n i n g l a m p c o m e s o n o n t h e
i n s t r u m e n t p a n e l a n d t h i s d i s p l a y a p -
p e a r s o n t h e i n s t r u m e n t p a n e l s c r e e n ,
c o n t a c t a C I T R O Ë N d e a l e r t o h a v e t h e
s y s t e m c h e c k e d . T h e a i r b a g s m a y n o
l o n g e r b e t r i g g e r e d i n t h e e v e n t o f a s e -
r i o u s i m p a c t .
T o e n s u r e t h e s a f e t y o f y o u r
c h i l d , t h e p a s s e n g e r a i r b a g
m u s t b e d e a c t i v a t e d w h e n y o u
i n s t a l l a " r e a r f a c i n g " c h i l d s e a t o n
the front passenger seat.
O t h e r w i s e , t h e c h i l d w o u l d r i s k b e i n g
s e r i o u s l y i n j u r e d o r k i l l e d i f t h e a i r b a g
w e r e t r i g g e r e d .
T h i s w a r n i n g l a m p c o m e s o n o n t h e
centre console front panel when the ig-
n i t i o n i s o n a n d u n t i l t h e a i r b a g i s r e a c -
t i v a t e d . Reactivation
W h e n y o u r e m o v e t h e c h i l d s e a t , t u r n
switch
A to the "ON" position to reacti-
v a t e t h e a i r b a g a n d s o e n s u r e t h e s a f e -
t y o f y o u r f r o n t p a s s e n g e r i n t h e e v e n t
o f a n i m p a c t .
T h e a s s o c i a t e d w a r n i n g l a m p g o e s o f f .
Deactivation
O n l y t h e f r o n t p a s s e n g e r ' s a i r b a g c a n
b e d e a c t i v a t e d :
with the ignition off , i n s e r t t h e k e y
i n t h e p a s s e n g e r a i r b a g d e a c t i v a -
tion switch A ,
t u r n i t t o t h e "OFF" p o s i t i o n ,
r e m o v e t h e k e y .
Page 106 of 217
VII
111
Stopping - Starting on a slope
Do not use the accelerator pedal to
immobilise the vehicle on a slope,
apply the
parking brake
instead.
When starting on a slope, accelerate
gradually while releasing the parking
brake.
Switching to sequential mode
Once you have moved off, you can
switch to sequential mode by selecting
position +/- .
"D" disappears and the gears engaged
appear in succession on the instrument
panel screen.
The gear change requests are only car-
ried out if the engine speed permits it.
Take your foot off the accelerator pedal
gently to engage the gear.
Switching to automated mode
Automated mode
After using the sequential mode, you
can return to the automated mode by
selecting position D .
"D" appears on the instrument panel
screen.
The gearbox then operates in auto-active
mode, without any action on the part of
the driver.
It continuously selects the gear most
suited to the conditions of:
- driving style,
- road characteristics,
- vehicle load.
To optimise driving comfort and obtain
the most suitable gear, avoid sharp
variations in the pressure on the
accelerator pedal.
Auto sequential mode
In the automated mode, you can take
over control temporarily at any time us-
ing the steering mounted controls.
The use of these controls permits manual
selection of the gears in situations which
require a faster changedown than that
offered in automated mode (arrival at a
roundabout, exit from a car park with a
steep gradient, overtaking...). Stopping the vehicle
Before switching off the engine, you can:
- move to position N to leave the
gearbox in neutral.
- l e a v e a g e a r e n g a g e d , s u c h a s fi r s t or reverse.
In both cases, you must apply the park-
ing brake to immobilise the vehicle.
Operating anomaly
With the ignition on, if the message
"Slow down" or "Maintenance re-
quired" appears on the multifunction
screen, this indicates a gearbox mal-
function.
When a message is displayed, carry
out the following operations:
- slow down and stop your vehicle in a safe place,
- place the lever in position N and let
the engine run,
- open the bonnet to allow the engine to cool.
If the message disappears for a long
period, you can set off again.
If the message remains displayed or
appears frequently, contact a CITROËN
dealer without delay.
P r e s s t h e b r a k e p e d a l fi r m l y
while starting the engine.
Start the engine. "N" appears on the
instrument panel screen.
S e l e c t fi r s t g e a r ( p o s i t i o n D or +/- ) or
reverse (position R ).
Release the parking brake.
Release the brake pedal then accelerate.
"D" or "1" or "R" appear on the instru-
ment panel screen. The gearbox engages the gear re-
quested if the engine speed permits it.
The gear engaged appears.
To return to the automated mode, press
the back of the
"+/OFF" control for ap-
proximately 2 seconds.
At low speeds, when approaching a
s t o p o r t r a f fi c l i g h t s f o r e x a m p l e , t h e
g e a r b o x c h a n g e s d o w n t o fi r s t g e a r
automatically.
Page 109 of 217
VII
D R I V I N G
114
"Normal" automatic mode
Select position D .
"D" appears on the instrument panel
screen.
The gearbox then operates in automatic
mode, without any action on the part of
the driver.
To optimise driving comfort and obtain
the most suitable gear, avoid sharp vari-
ations in the pressure on the accelera-
tor pedal.
"Temporary" manual mode
In automatic mode, you can take
control temporarily at any time using
the steering mounted controls.
The use of these controls permits man-
ual selection of the gears in situations
which require a faster changedown than
that offered in automatic mode (arrival
at a roundabout, exit from a car park
with a steep gradient, overtaking...).
The gearbox engages the gear re-
quested if the engine speed permits it.
The gear engaged appears.
To return to the automatic mode, press
the back of the "+/OFF" control for at
least 2 seconds.
"Sport" automatic mode
From automatic mode, you can engage
"Sport" mode.
With the vehicle moving or stationary,
push the thumbwheel A forward.
"SPORT" appears on the instrument
panel screen.
Switching off "Sport" automatic
mode
You can return to "Normal" automatic
mode at any time:
Push the thumbwheel A rearward
once. Before switching off the engine, you
must engage position
P or N to place
the gearbox in neutral.
You must apply the parking brake to im-
mobilise the vehicle.
The gear lever must be in position P
to
remove the ignition key.
Stopping the vehicle
Hill start assist
To assist you when starting on a gradi-
e n t , y o u r v e h i c l e i s fi t t e d w i t h a s y s t e m
w h i c h i m m o b i l i s e s i t b r i e fl y ( a p p r o x i -
mately 2 seconds), the time required to
move your foot from the brake pedal to
the accelerator pedal. This function is
only active when the vehicle has been
completely immobilised with your foot
on the brake pedal and on certain gra-
dients.
Do not get out of the vehicle during
the hill start
assist
temporary immo-
bilisation phase.
To immobilise the vehicle on a gradient
for a longer period, you must use the
parking brake, not the accelerator.
When starting on a gradient, accelerate
gradually while releasing the parking
brake.
Page 110 of 217
VII
D R I V I N G
115
Operating anomaly Reverse gear
Flashing of the indicator R in the instru-
ment panel screen, accompanied by an
audible signal, indicates a malfunction
on engaging the gear:
Press the brake pedal, position the gear
lever in position N and engage reverse
gear again.
With the ignition on, if this warning
light comes on, accompanied by vi-
bration in the pedals and the message
"Maintenance required" on the in-
strument panel display, this indicates a
gearbox malfunction.
If the message is displayed, carry out
the following operations:
- slow down and stop your vehicle in a safe place,
- place the lever in position P or N ,
apply the handbrake and let the
engine run,
- open the bonnet to allow the engine to cool.
If the message disappears for a long
period, you can set off again.
If the message remains displayed or
appears frequently, contact a dealer of
the Marque without delay.
Overheating of the engine may re-
sult in unwanted declutching of the
gearbox.
Page 113 of 217
VII
D R I V I N G
118
Programming
Press button 1 .
Set the programmed speed by ac-
celerating to the required speed,
then press button 2 "COAST SET" .
CRUISE CONTROL
The controls of this system are grouped
together on the steering wheel.
1. "ON/OFF" button: activation/deacti-
vation of the cruise control mode.
2. "COAST SET" button: storing of a
driving speed and decreasing of the
cruising speed.
3. "ACC RES" button: increasing of
the cruising speed and recalling of
the stored speed.
4. "CANCEL" button: switching off of
the cruise control. When you press button
1 , the "CRUISE"
indicator comes on in the instrument
panel.
Steering mounted controls Display on the instrument panel
The cruise control cannot, in any cir-
cumstances, take the place of the
need to comply with speed limits or
of the vigilance and responsibility of
the driver.
System which automatically maintains
the vehicle speed at the value pro-
grammed by the driver, without any ac-
tion on the accelerator pedal.
The cruise control is
switched on
manually: the vehicle speed must be
25 mph (40 km/h) minimum and sec-
ond gear must be engaged in the case
of a manual gearbox.
The cruise control is switched off man-
ually, by an action on the brake or clutch
pedal or if the ASC system is triggered.
The programmed speed can be ex-
ceeded temporarily by pressing the
accelerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value.
Page 121 of 217
VIII
C H E C K S
126
CHECKING LEVELS Brake fluid level To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.
Oil level
The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either when
the ignition is switched on using the oil
level indicator on the instrument panel,
or using the dipstick. T h e b r a k e fl u i d l e v e l s h o u l d b e
between the "MAX" and "MIN"
marks.
If it is not, check the brake pad
wear.
C h a n g i n g t h e b r a k e fl u i d
Refer to the servicing booklet for details
of the interval for this operation.
Coolant level
The coolant level must be
measured when the engine is
cold and should be between
the "LOW" and "FULL" marks.
When the engine is warm, the tem-
perature of the coolant is regulated
by the fan. This can operate with the
ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h a
p a r t i c l e e m i s s i o n fi l t e r , t h e f a n m a y
operate after the vehicle has been
s w i t c h e d o f f , e v e n i f t h e e n g i n e i s
cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.
Screenwash and headlamp wash * fluid
C h e c k t h e fl u i d l e v e l r e g u l a r l y ,
using the gauge.
* According to country.
Changing the engine oil
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.
O i l s p e c i fi c a t i o n
The oil must correspond to your en-
gine and conform to the manufacturer's
recommendations. F l u i d s p e c i fi c a t i o n
T h e b r a k e fl u i d m u s t c o n f o r m t o t h e
manufacturer's recommendations and
f u l fi l t h e D O T 4 s t a n d a r d s .
C h a n g i n g t h e c o o l a n t fl u i d
Refer to the servicing booklet for details
of the interval for this operation.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the manu-
facturer's recommendations.
F l u i d s p e c i fi c a t i o n
T h i s fl u i d m u s t c o n f o r m t o t h e m a n u f a c -
turer's recommendations for optimum
cleaning.
Power steering fluid level
C h e c k t h e fl u i d l e v e l w i t h t h e e n g i n e a t
idle.
C h e c k t h a t t h e p o w e r s t e e r i n g fl u i d
level is always between the "MAX" and
"MIN" marks and top up if necessary.
F l u i d s p e c i fi c a t i o n
T h i s fl u i d m u s t c o n f o r m t o t h e m a n u f a c -
turer's recommendations.
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
I f a l e v e l d r o p s s i g n i fi c a n t l y , h a v e t h e
corresponding system checked by a
CITROËN dealer.
When working under the bonnet, take
care as certain areas of the engine may
be extremely hot (risk of burns).
Page 157 of 217
XI
162
A U D I O a n d T E L E M A T I C S
STEERING MOUNTED CONTROLS
1. On/Off and selection of
radio or
CD mode
2. Volume decrease
3. Volume increase
4.
Search for a higher radio frequency/
Next track/Fast forwards play
5.
Search for a lower radio frequency/
Previous track/Fast backwards play
Switching off
Press button 1 for more than two seconds.
Selecting the source
Press button 1 .
The source changes in the following order: FM1/FM2/FM3/MW/LW/CD/FM1... Searching in radio mode
Press button
4 or 5 to search for a
higher or lower radio frequency respec-
tively.
Searching in CD mode
Press button 4 or 5 to select the next or
previous track on the CD respectively.
Press and hold button 4 or 5 for fast for-
wards or fast backwards playing of the
current track of the CD respectively.
Switching on
Press button
1 for more than two seconds.
The last source selected before switching
off comes back into operation.
Adjusting the volume
Press and hold button 2 or 3 to decrease
or increase the volume respectively. While a track is being played, press
button
5 once to return to the beginning
of this track.
They can be used when the ignition
switch is in the "ON" or "ACC" position.
Page 158 of 217
XI
163
A U D I O a n d T E L E M A T I C S
GENERAL FUNCTIONS
Switching on
Press the "PWR" button.
The last source selected be-
fore switching off resumes
operation.
Adjusting the volume
Turn the "VOL" dial respec-
tively to the left to decrease
the volume or to the right to
increase it.
Switching off
Press the "PWR" button again.
Setting the audio modes
Press the "SOUND" but-
ton several times; the audio
modes change in the follow-
ing order:
SUB PUNCH/TYPE/FIELD/
BASS/MID/TREBLE/FADER/
BALANCE/OFF.
Quick access mode
To access the personalised sound func-
tions quickly, press and hold this button,
then turn it to reach the personalised
sound setting of your choice.
Release the button to store the setting.
"Hold" mode
If you press this button for more than
2 seconds in the audio setting mode,
the system switches to "Hold" mode.
The audio mode selected will be re-
tained until you press this button again
for more than 2 seconds.
Selecting the musical ambience "TYPE"
Turn the "SOUND" dial; the
musical ambiences change
in the following order:
CLASSIC/JAZZ/POP/ROCK/
HIP-HOP.
Once the ambience has been selected,
p r e s s t h e " S O U N D " b u t t o n t o c o n fi r m .
"CLASSIC": optimises the acoustics to
obtain perfect equalisation of the sound
for classical music.
"JAZZ": optimises the acoustics to ob-
t a i n a n a m b i e n t s o u n d w i t h s p e c i fi c
modulations in the bass, mid tone and
treble for jazz.
"POP": optimises the acoustics to ob-
tain clear vocals and modulation of the
bass and treble for pop music.
"ROCK": optimises the acoustics to ob-
tain a sound in harmony with the rhythm
which places the emphasis on the mid
tone for rock music.
"HIP-HOP": optimises the acoustics to
obtain a powerful sound and accentua-
tion of the bass for hip-hop music.
If the "TYPE" is changed, the sound
c u t s o u t b r i e fl y .
The audio setting mode is deactivat-
ed when the radio is operated or a
CD is played or after approximately
10 seconds without any action.
The audio equipment functions can be
used when the ignition switch is in the
"ON" or "ACC" position.
Page 211 of 217
XI
215
A U D I O a n d T E L E M A T I C S
Matching your Bluetooth®
telephone
The system can register up to 7 Bluetooth®
compatible mobile telephones.
The telephone which has the highest
level of priority is connected automati-
cally.
It is absolutely essential that the vehicle
is parked in a safe place with the park-
ing brake applied.
1 - Press the SPEAK button.
7 - Say a 4-digit number which will be recorded as the match-
ing code. 11 - When it detects a Bluetooth
®
compatible mobile telephone,
the system says "Please say
the name of the telephone
after the bleep". If the system does not detect the
Bluetooth
®
compatible mobile tele-
phone, the matching process stops
accompanied by an audible signal.
If you select a level of priority which
has already been allocated to an-
other telephone, the system asks
you if you wish to replace this level
of priority.
Remember this matching code as
you must enter it in the telephone
in one of the following steps of the
matching procedure.
9 - The system says "Start the matching procedure on the telephone. Con-
sult the instructions in the telephone
manual".
2 - S a y " C o n fi g u r e " .
3 - Say "Matching options".
5 - Say "Match a telephone". 8 - T h e s y s t e m c o n fi r m s t h e v a -
lidity of the number spoken,
answer "Yes". Say "No" to re-
turn to step 7.
10 - Consult your mobile tele- phone's user manual and
enter the matching code
recorded in step 7 in the
telephone. 12 - After the audible signal, allo-
cate a name to the telephone
by saying the name of your
choice.
13 - The system says "Allocate an order of priority between 1 and 7. One is
the highest level of priority".
14 - Say a number between 1 and 7 to establish the level
of priority of the mobile tele-
phone.
1 5 - T h e s y s t e m s a y s a n d c o n fi r m s t h e
4 - The system says "Do you wish to match a telephone, delete a tele-
phone or obtain the list of matched
telephones?".
6 - The systems says "Please say the 4 digits of a matching code". If the code is incorrect, the system
locks. To clear the code:
- check that the telephone's voice
recognition is not activated,
- with the ignition on and the audio system active, press the HANG UP
button for 2 seconds, 3 times in
succession. 16 - Answer "Yes" or say "No" to
return to step 13.
17 - The systems says "Matching complete" then emits an audible
signal and deactivates the voice
recognition.