turn signal CITROEN C1 2019 Owners Manual

20
Warning / indicator lamp State Cause Action / Observations
Keyless Entr y
and Starting
system flashing
 qu

ickly.The
  steering   column   has   not   been  
u

nlocked.Change
  to   "OFF "
  mode,   then   "ON "
  mode   and   turn   the  
w

heel   slightly   to   unlock   the   steering   column.
flashing,
 a

ccompanied
 b

y   an   audible   signal.The
  battery   in   the   electronic   key   is  
d

ischarged.Replace
  the   battery.
Refer
  to   the   corresponding   section.
You
  are   leaving   the   vehicle   without  
a

ctivating   "OFF "
  mode.With
  the   electronic   key   on   your   person,   press   the  
S

TART/STOP   button   to   change   to   "OFF "
  mode.
The
  electronic   key   has   not   been  
d

etected.Check
  that   you   have   the   electronic   key   with   you.
The
  Keyless   Entry   and   Starting  
s

ystem   has   a   fault.Have
  the   system   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Lane departure
warning system flashing
 (

orange),
 a

ccompanied   by   an  
a

udible
 s
ignal.A
  lane   marking   is   being   crossed,   on  
t

he   right.Turn
  the   wheel   in   the   other   direction   to   return   to   the  
c

orrect
 t
rajectory.
For
  more   information,   refer   to   the   corresponding  
s

ection.
A
  lane   marking   is   being   crossed,   on  
t

he   left.
fixed. The
  lane   departure   warning   system  
h

as   a   fault.Have
  the   system   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Active City
Brake flashing,
 a

ccompanied
 b

y   an   audible   signal.The
  Active   City   Brake   system   is   in  
a

ction.The
  system   optimises   braking   to   avoid   a   collision.
For
  more   information,   refer   to   the   corresponding  
s

ection.
flashing. The
  Active   City   Brake   system   has   a  
f

ault.Have
  the   system   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Instruments

21
C1_en_Chap01_instrument- de-bord_ed01-2016
Operation indicator lamps
Left-hand
direction indicatorflashing with buzzer.The   lighting   stalk   is   pushed   down.
Right-hand
direction indicatorflashing with buzzer.The   lighting   stalk   is   pushed   up.
Sidelamps or
dipped beam
headlamps fixed.
The
  sidelamps   or   dipped   beam  
h

eadlamps   are   on.
Main beam
headlamps fixed.
The
  lighting   stalk   is   pulled   towards   you.Pull
  the   stalk   to   return   to   dipped   beam   headlamps.
Warning


/ indicator lamp
State Cause Action

/ Observations
Illumination
 
of
 
one
 
of
 
the
 
following   indicator   lamps   confirms   that   the   corresponding   system   has   been   switched   on.
It
 
may
 
be
 
accompanied
 
by
 
an
 
audible   signal.
Rear foglamp fixed. The
  rear   foglamp   has   been   switched  
o

n   using   the   ring   on   the   lighting  
c

ontrol   stalk. Turn
  the   ring   on   the   lighting   control   stalk   to   the   rear   to  
s

witch   off   the   rear   foglamp.
1
Instruments

79
C1_en_Chap04_conduite_ed01-2016
Temporarily taking control of
gear changes
You can temporarily take control of gear changes   using   the   "+"  and   "-" steering
 
m

ounted   control   paddles.
Gear
  change   commands   are   only   acted   on   if  
t

he   engine   speed   allows.   There   is   an   audible  
s

ignal   if   a   command   is   not   accepted.
The
  gear   engaged   is   displayed   in   the  
in

strument
 pan
el.
This function allows you to anticipate certain
situations
  such   as   overtaking   a   vehicle   or  
a

pproaching   a   corner.
After
  a   few   moments   with   no   action   on   the  
c

ontrols,   the   gearbox   returns   to   automatic  
c

ontrol   of   the   gears. It
  is   possible   to   change   mode   at   any   time,   by  
m

oving   the   gear   selector   from   position   E to
position M
  and   the   other   way   round.
Never select neutral N when the vehicle
is
  moving.
F
 
P
lace   the   gear   selector   in   position   M
.
F  
C
hange   up   or   down   using:
-  t he   gear   selector,   pushing:
-  b ack,   "+"  to   change   up,
-
 
f
or ward,   "-"
 
to   change   down.
-
 
o
r   the   "+" or "-"
 

steering   mounted  
c

ontrol   paddle.
The
  gear   engaged   is   displayed.
Gear
  change   commands   are   only   acted   on   if  
t

he   engine   speed   allows.
It is not necessary to release the accelerator
peal
  during   gear   changes.   There   is   an   audible  
s

ignal   if   a   command   is   not   accepted.
When
  braking   or   slowing   down,   the   gearbox  
a

utomatically   changes   down   so   that   pick-up   is  
i

n   the   right   gear.
Manual mode
Under sharp acceleration, the gearbox will not   change   up   without   action   by   the   driver   on  
t

he   gear   selector   or   steering   mounted   control  
p

addles   (unless   the   engine   speed   is   close   to  
m

aximum).
To
  engage   reverse,   the   vehicle   must   be  
s

tationary   with   your   foot   on   the   brake   pedal.
F

Sel
ect position R .
Reverse
There is an audible signal on engaging reverse.
4
Driving

80
C1_en_Chap04_conduite_ed01-2016
The vehicle can be stopped whatever the position   of   the   gear   selector   (N , E or R ).
However,
  there   is   an   audible   signal   on   opening  
t

he   driver's   door   if   the   gear   selector   is   not   at  
p

osition N .
Switching off
When the vehicle is stopped with the e
ngine   running,   always   put   the   gear  
s

elector to neutral N .
There
  is   a   continuous   audible   signal  
i

f   you   turn   the   ignition   switch   to   "OFF "
with
  the   vehicle   in   2
nd, 3rd, 4th or 5th ge a r.
In
 
this
 
case
 
return
 
the
 
ignition
 
switch  
t

o " ON ",
 
move
 
the
 
gear
 
selector
 
to  
p

osition


N , then to position E , M or R,
then
 
turn
 
the
 
ignition
 
switch
 
to
 
" OFF ".
On
 
a
 
slope,
 
use
 
the
 
brakes
 
to
 
i

mmobilise
 
the
 
vehicle
 
and
 
place
 
the  
g

ear
 
selector
 
in
 
position
 
N , E or R . With
  the   ignition   on,   illumination  
o

f   this   warning   lamp   indicates   a  
g

earbox   fault.
Contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating faults
In all cases, it is essential
that you
apply the parking brake  to   immobilise  
t

he   vehicle.
Before
  doing   anything   under   the  
b

onnet,   check   that   the   gear   selector   is  
i

n neutral N   and   the   parking   brake   is  
a

pplied.
Limits of operation
On a gradient, or when hill start assist is activated, n ever hold the vehicle using the
accelerator :
  you   could   damage   the   clutch.
In
  these   situations   there   is   an   audible   signal.
F
 
M
ove   the   gear   selector   to   position   N.
F
 
W
ait   15   minutes   to   allow   the   clutch   to   cool  
d

own   before   setting   off. -
 
c
heck   that   the   ignition   switch   is   at   the  
"
O
N
"

position,
-  
p
lace   the   gear   selector   at   N
,   then   move   it  
t

o E
, M or R .
If 1   is   flashing   in   the   instrument   panel:
-  p lace   the   gear   selector   at   E or M
, then
move   it   to   N.
If R
  is   flashing   in   the   instrument   panel:
-
 
p
lace   the   gear   selector   at   R,
  then   move   it  
t

o N.
If
N is   flashing   in   the   instrument   panel
 a

ccompanied   by   an   audible   signal   for   a   long   time:
Driving

88
C1_en_Chap04_conduite_ed01-2016
Switching off
F Press  the   end   of   the   control   stalk. T
he   display   of   information   related   to   the  
sp

eed
 l
imiter
 d
isappears.
Operating fault
Illumination of this warning lamp in the   instrument   panel   indicates   a   fault  
w

ith   the   speed   limiter.
Have
  it   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
The
  use   of   mats   not   approved   by  
C

ITROËN   may   inter fere   with   the  
o

peration   of   the   speed   limiter.
To
 
avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
d
o   not   fit   one   mat   on   top   of   another.
Temporarily exceeding the
programmed speed
F Press f irmly  on   the   accelerator   pedal,  g
oing   beyond   the   point of resistance, to
exceed
  the   programmed   speed   limit.
The
  speed   limiter   is   deactivated   temporarily  
a

nd   the   displayed   programmed   speed   flashes.
As
  soon   as   the   vehicle's   speed   returns   to   the  
p

rogrammed   value,   the   limiter   operates   again:  
t

he   display   of   the   programmed   speed   becomes  
s

teady   again.
An
  audible   signal   accompanies   the  
f

lashing   of   the   programmed   speed  
w

hen   exceeding   the   speed   is   not   due   to  
a

n   action   by   the   driver   (steep   hill...).
Driving

91
C1_en_Chap04_conduite_ed01-2016
Switching off
F Press  the   end   of   the   control   stalk T
he   display   of   information   related   to   the  
sp

eed
 l
imiter
 d
isappears.
Operating fault
Illumination of this warning lamp in the   instrument   panel   indicates   a   fault  
w

ith   the   speed   limiter.
The
  use   of   mats   not   approved   by  
C

ITROËN   may   inter fere   with   the  
o

peration   of   the   speed   limiter.
To
 
avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
d
o   not   fit   one   mat   on   top   of   another.
Temporarily exceeding the
programmed speed
F Press f irmly  on   the   accelerator   pedal,  g
oing   beyond   the   point of resistance,
to
exceed
  the   programmed   speed   limit.
The
  speed   limiter   is   deactivated   temporarily  
a

nd   the   displayed   programmed   speed   flashes.Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
An
  audible   signal   accompanies   the  
f

lashing   of   the   programmed   speed  
w

hen   exceeding   the   speed   is   not   due   to  
a

n   action   by   the   driver   (steep   hill...).
As
  soon   as   the   vehicle's   speed   returns   to   the  
p

rogrammed   value,   the   limiter   operates   again:  
t

he   display   of   the   programmed   speed   becomes  
s

teady   again.
4
Driving

100
C1_en_Chap05_eclairage-visibilite_ed01-2016
Foglamp selection ring
The foglamp operates with the dipped and main beam h eadlamps.
F
 
T
urn   the   ring   for ward   and   release   to   switch  
o

n   the   rear   foglamp.
When
  the   lighting   is   switched   off   automatically  
(

with   AUTO   model)   or   when   the   dipped   beam  
h

eadlamps   are   switched   off   manually,   the  
f

oglamp   and   the   sidelamps   will   remain   on.
F
 
T
urn   the   ring   rear ward   and   release   to  
s

witch   off   all   the   lamps.
Rear
 fo

glamp. In
  good   or   rainy   weather,   both   day  
a

nd   night,   use   of   the   rear   foglamp   is  
p

rohibited.   In   these   situations,   the  
p

ower   of   its   beam   may   dazzle   other  
d

rivers.   It   should   only   be   used   in   fog   or  
s

now.
In   these   weather   conditions,   it   is   your  
r

esponsibility   to   switch   on   the   foglamp  
a

nd   dipped   beam   headlamps   manually  
a

s   the   sunshine   sensor   may   detect  
s

ufficient   light.
Do   not   forget   to   switch   off   the   rear  f
oglamp   when   it   is   no   longer   needed.
Switching off the lamps when
the ignition is switched off
On switching off the ignition, all of the l
amps   turn   off   immediately,   except   for  
d

ipped   beam   if   guide-me-home   lighting  
i

s   activated.
Switching on the lamps
after the ignition is
switched off
To reactivate the lighting control, rotate the   ring   to   the   "0"  position   -   lamps   off,  
t

hen   to   the   desired   position.
On
  opening   the   driver's   door   a  
c

ontinuous   audible   signal   warns   the  
d

river   that   the   lighting   is   on.
Lighting and visibility

221
C1_en_Chap10a_ Autoradio-Toyota-tactile-1_ed01-2016
Level 1Level 2 Comments
Connection GPS The
  compass   is   available   only   with   a   fixed   position.
The
  direction   is   available   only   with   a   fixed   position.
The
  representation   of   the   sky   is   facing   north,   as   for   the   compass.
The
  satellite   icons   are   represented   in   yellow   for   a   weak   signal   and   in  
g

reen   for   a   strong   signal.
The
  satellite   signal   levels   are   represented   in   yellow   for   a   weak   signal  
a

nd   in   green   for   a   strong   signal.
Connection Page info Search for POI nearby
Display
  the   information   on   your   current   position   and   select   the   desired  
se

ttings.
Add to favorites
Set as home
GPS
Connection Navigation Return home
Create
  a   route   to   a   place   set   as   "Home".
Map Go
  directly   to   the   map   page.
Route overview Display
  an   overview   of   your   route.
User settings Display
  the   system   preferences   (language,   units,   ...).
Go to Search
  for   and   set   a   destination.
Map settings Display
  the   route   and   map   display   preferences.
.
Audio and Telematics

223
C1_en_Chap10a_ Autoradio-Toyota-tactile-1_ed01-2016
Level 1Level 2 Level 3 Comments
Navigation
Return home Press
  the   change   of   direction   indicator   to   open   the   list  
o

f   changes   of   direction.
Press
  the   time   information   area   to   alternate   the  
i

nformation   displayed:   estimated   time   of   arrival   /  
r

emaining
 t
ime.
Press
  the   distance   information   area   to   alternate   the  
i

nformation   displayed:   remaining   distance   /   distance  
t

ravelled.
Navigation Map Go
  directly   to   the   navigation   menu.
Map
  orientation   and   scale.
Press
  to   zoom   in.
Press
  to   zoom   out.
Indicates
  the   strength   of   the   GPS   signal.
Search for POIs nearby Display
  the   information   on   your   current   position   and  
s

elect   the   desired   settings.
Add
  to   favourites
Set
  as   home
Navigation
Route overview Point
  of   departure
Display the distance and information on the duration of the journey.
Display the total distance and information on the total duration of the journey.
Point of arrival.
D eparture
 t
ime.
Distance
 t

ravelled.
Estimated
  time   of   arrival.
.
Audio and Telematics

242
C1_en_Chap10b_ Autoradio-Toyota-2_ed01-2016
Radio
Selecting a stationPresetting a station
Press on "MODE" to select the FM or
AM   waveband. Press on "
MODE" to select the FM or
AM   waveband.
Turn
  the   dial   to   carry   out   a   manual  
s

earch   down/up   for   radio   stations.
In
  FM   mode,   press   the   "List " button
to
  display   the   list   of   stations   received  
l

ocally.
Press on " Update"
  to   refresh   the   list.Press
  and   hold   one   of   the   buttons   to  
p

reset   the   current   radio   station.   The  
n

ame   of   the   station   is   displayed   and  
a

n   audible   signal   confirms   the   preset.
Briefly press one of the buttons to
carry
  out   an   automatic   search   down/
up
  for   radio   stations. Briefly press one of these buttons to
start
  an   automatic   search   up/down  
f

or   frequencies.
Press one of the buttons to select the
chosen
  radio   station   then   confirm.The
  surroundings   (hills,   buildings,  
t

unnel,   parking,   under   ground...)   may  
p

revent   reception,   including   RDS  
a

lternative   frequencies,   frequency  
sea

rch.
This
  phenomenon   is   normal   in   the  
p

ropagation   of   radio   waves   and   does  
n

ot   in   any   way   imply   a   fault   with   the  
a

udio   system.
Alternative frequencies
(AF) / RDS
Press on "MENU"   to   display   the   list.
Turn   the   knob   to   select   "Radio " then
press
  to   confirm.
Turn
  the   knob   to   select   "FM AF " then
press
  to   activate   or   deactivate   the  
f

requency.
Turn
  the   knob   the   select   "Region
Code " then press to activate or
deactivate.
When
  alternative   frequencies   (AF)   is  
a

ctivated,   the   system   selects   the   best  
R

DS   frequency   (Region   code)   for   the  
s

tation   being   listened   to.
However,   in   certain   conditions,   tracking  
o

f
 
a
  station   is   not   available   throughout  
t

he
 
whole   country,   as   radio   stations   do  
n

ot
 
cover   100%   of   the   country.   When  
r

eception   becomes   poor,   the   frequency  
c

hanges   to   a   regional   station.
Audio and Telematics