wheel bolts Citroen C1 DAG 2008 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C1 DAG, Model: Citroen C1 DAG 2008 1.GPages: 97, PDF Size: 3.15 MB
Page 75 of 97
9
70
PRACTICAL INFORMATION R e fi t t i n g t h e w h e e l
1. Position the wheel.
2. Screw in the bolts fully by hand.
Removing the wheel
1. Remove the trim.
2. Release the wheel bolts using the
wheelbrace 1 .
3. Place the jack 2 in contact with
one of the four locations A pro-
vided on the underframe, the
one closest to the wheel to be
changed.
4. Extend the jack 2 until its base
is in contact with the ground. En-
sure that the centreline of the jack
base is directly below the location
A used.
5. Lift the vehicle.
6. Remove the bolts and detach the
wheel.
3. Pre-tighten * using the wheel-
brace 1 .
* I f y o u r v e h i c l e i s fi t t e d w i t h a l l o y w h e e l s , w h e n t i g h t e n i n g t h e b o l t s i t i s normal
to notice that the washers do not come into contact with t he spare wheel. It is
fi x e d s e c u r e l y .
Page 76 of 97
9
71
PRACTICAL INFORMATION
CHANGING A BULB
1. Side lights (W 5 W)
Turn the bulb holder A one quar-
ter of a turn and remove it.
Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)
Turn the bulb holder B one quar-
ter of a turn and remove it.
Turn the bulb one quarter of a
turn.
Remove the bulb and change it.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s , c o n -
tact a CITROËN dealer.
Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
condensation on the in-
ternal face of the headlamps is
normal ; it disappears a few minutes
after the lights are switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
4. Fold the jack 2 and detach it.
5. Tighten the wheel bolts using the
wheelbrace 1 .
6. R e fi t t h e t r i m .
7. Store the tools and the wheel in
the boot.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
- have the tightening of the bolts and the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel re- p a i r e d a n d r e fi t i t o n t h e v e h i c l e
as soon as possible.
Consult a CITROËN dealer. Front lights
1. Side lights
2. Direction indicators
3. Dipped headlamps/Main beam
headlamps
Page 77 of 97
9
71
PRACTICAL INFORMATION
CHANGING A BULB
1. Side lights (W 5 W)
Turn the bulb holder A one quar-
ter of a turn and remove it.
Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)
Turn the bulb holder B one quar-
ter of a turn and remove it.
Turn the bulb one quarter of a
turn.
Remove the bulb and change it.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s , c o n -
tact a CITROËN dealer.
Note: in certain climatic con-
ditions (low temperatures,
humidity), the presence of
condensation on the in-
ternal face of the headlamps is
normal ; it disappears a few minutes
after the lights are switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
4. Fold the jack 2 and detach it.
5. Tighten the wheel bolts using the
wheelbrace 1 .
6. R e fi t t h e t r i m .
7. Store the tools and the wheel in
the boot.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
- have the tightening of the bolts and the pressure of the spare wheel
checked as soon as possible,
- have the punctured wheel re- p a i r e d a n d r e fi t i t o n t h e v e h i c l e
as soon as possible.
Consult a CITROËN dealer. Front lights
1. Side lights
2. Direction indicators
3. Dipped headlamps/Main beam
headlamps