ESP Citroen C3 2012 2.G Owner's Guide

9
125
DRIVING
The cruise control cannot, in any circumstances, replace the need to respect speed limits, nor can it re-
place the need for vigilance and re-
sponsibility on the part of the driver.
CRUISE CONTROL
System which automatically maintains
the speed of the vehicle at the value
programmed by the driver, without any
action on the accelerator pedal.
The cruise control is switched on

manually: it requires a minimum vehicle
speed of 25 mph (40 km/h), as well as
the engagement of:


- fourth gear on a manual gearbox,

- second gear on a or automatic or elec-
tronic gearbox, in sequential mode,

- position A
on an electronic gearbox
or position D
on an automatic gearbox.

The cruise control is switched off
man-
ually or by pressing the brake or clutch
pedal or on triggering of the ESP system
for safety reasons.
It is possible to exceed the programmed
speed temporarily by pressing the ac-
celerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value. The controls of this system are grouped
together on stalk A
.


1.
Cruise control mode selection thumb
wheel.

2.
Value decrease button.

3.
Value increase button.

4.
Cruise control off/resume button.

Steering mounted controls
Displays in the instrument panel

The programmed information is grouped
together in the instrument panel screen.

5.
Cruise control off/resume indication.

6.
Cruise control mode selection indi-
cation.

7.
Programmed speed value.

9
128
DRIVING
The system will be deactivated
automatically when towing a
trailer or when a bicycle carrier is
fi tted (vehicle fi tted with a towbar
or bicycle carrier recommended
by CITROËN). In bad or wintry weather, ensure
that the sensors are not covered
with mud, frost or snow.


Programming

You can activate or deactivate the
system by means of the multifunction
screen confi guration menu. The system
state is memorised when switching off
the ignition.
For more information on access to
the parking sensors menu, refer to
"Confi guration/Vehicle parameters" in
the "Multifunction screens" section cor-
responding to your screen.
Operating faults
If there is an operating fault,
when reverse gear is en-
gaged this warning lamp
comes on in the instrument panel, ac-
companied by an audible signal (short
beep) and a message in the multifunc-
tion screen.

10
133
CHECKS
CHECKING LEVELS
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
If a level drops signifi cantly, have the
corresponding system checked by a
CITROËN dealer or a qualifi ed work-
shop.

Oil level

The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 30 minutes.
The check is carried out either when the igni-
tion is switched on using the oil level indicator
in the instrument panel, or using the dipstick.

Engine oil change
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.

Oil grade
The oil must be suitable for your engine
and conform to the manufacturer's rec-
ommendations.


The brake fl uid level should be
close to the "MAX" mark. If it is
not, check the brake pad wear.

Changing the fl uid
Refer to the servicing booklet for details
of the interval for this operation.

Fluid specifi cation
The brake fl uid must conform to the
manufacturer's recommendations and
meet the DOT4 standard.

Coolant level

The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the
temperature of the coolant is regulated
by the fan. This can operate with the igni-
tion off.

On vehicles which are fi tted with a par-
ticle emission fi lter, the fan may oper-
ate after the vehicle has been switched
off, even if the engine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work. To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.

Changing the coolant

The coolant does not have to be changed.


Fluid specifi cation
The coolant must conform to the manu-
facturer's recommendations.



Screenwash fluid level

Top up the level when neces-
sary.

Fluid specifi cation
For optimum cleaning and to avoid
freezing, this fl uid must not be topped
up or replaced with plain water.



Take care when carrying out
checks under the bonnet as
some parts of the engine can be
very hot (risk of burns).
It is normal to top up the engine
oil between services. CITROËN
recommends that you check the
oil level and top up if necessary,
every 3 000 miles (5 000 kilome-
tres).

11
148
PRACTICAL INFORMATION
Rear lamps


1.
Brake/sidelamps (P21/5W).


2.
Direction indicators
(PY21W amber)


3.
Foglamp,

right-hand side
(

PR21W red)


Reversing lamp

,

left-hand side
(

P21W).

These four bulbs are changed from
inside the boot:


)
open the boot,

)
remove the access fl ap from the
corresponding side trim panel,

)
unscrew the butterfl y nut securing
the lamp unit,

)
unclip the lamp unit connector,

)
extract the lamp unit carefully pulling
in its middle towards the outside,

)
spread the four tabs and remove the
bulb holder,

)
turn the bulb a quarter of a turn and
change it.
To r efi t, carry out these operations in re-
verse order.
Take care to engage the lamp unit in its
guides, while keeping it in line with the
vehicle.
Changing bulbs
Amber or red bulbs, such as
those for the direction indica-
tors and rear foglamp, must be
replaced by bulbs of the same
rating and colour.
The lamps on the tailgate are
dummy units. They are there for
aesthetic purposes only.

11
151
PRACTICAL INFORMATION
CHANGING A FUSE
Procedure for replacing a faulty fuse
with a new fuse to rectify a failure of the
corresponding function.

Access to the tools

The extraction tweezer and the spare
fuses are located on the back of the
dashboard fusebox cover.
For access to them:


)
unclip the cover by pulling on the
side,

)
remove the cover completely,

)
remove the pliers.

Changing a fuse

Before changing a fuse, the cause of
the failure must be identifi ed and recti-
fi ed.


)
Identify the faulty fuse by checking
the condition of its fi lament.

Good

Failed



)
Use the special tweezer to extract
the fuse from its housing.

)
Always replace the faulty fuse with a
fuse of the same rating.

)
Check the correspondence between
the number marked on the box, the
rating marked on the fuse and the
tables below.
Installing electrical
accessories
Your vehicle's electrical system
is designed to operate with stan-
dard or optional equipment.
Before installing other electrical
equipment or accessories on
your vehicle, contact a CITROËN
dealer or a qualifi ed workshop.
CITROËN will not accept respon-
sibility for the cost incurred in
repairing your vehicle or for recti-
fying malfunctions resulting from
the installation of accessories not
supplied and not recommended
by CITROËN and not installed in
accordance with its instructions,
in particular when the combined
consumption of all of the addi-
tional equipment connected ex-
ceeds 10 milliamperes.

11
154
PRACTICAL INFORMATION

Engine compartment fusebox

The fusebox is located in the engine
compartment near the battery (left-hand
side).

All work on the fuses in the fuse-
box located on the battery must
be carried out by a CITROËN
dealer or a qualifi ed workshop.
Access to the fuses


)
Unclip the cover.

)
Change the fuse (see corresponding
paragraph).

)
When you have fi nished, close the
cover carefully to ensure correct
sealing of the fusebox.

11
PRACTICAL INFORMATION

Fuse table


Fuse N°



Rating


Functions



F1



20 A

Engine control unit supply, cooling fan unit control
relay, multifunction engine control main relay,
injection pump (Diesel).


F2



15 A

Horn.


F3



10 A

Front/rear wash-wipe.


F4



20 A

Daytime running lamps.


F5



15 A

Diesel heater (Diesel), particle fi lter additive pump
(Diesel), air fl ow sensor (Diesel), fuel pump (1.1i
and 1.4i), blow-by heater and electrovalves (VTi).


F6



10 A

ABS/ESP control unit, secondary brake lamp
switch.


F7



10 A

Electric power steering, automatic gearbox.


F8



25 A

Starter motor control.


F9



10 A

Switching and protection unit (Diesel).


F10



30 A

Fuel heater (Diesel), blow-by heater (1.1i, 1.4i and
Diesel), fuel pump (VTi), injectors and ignition coils
(petrol), electronic thermostat and canister purge
electrovalve (1.1i and 1.4i).


F11



40 A

Heater blower.

11
156
PRACTICAL INFORMATION


Fuse N°



Rating


Functions



F12



30 A

Windscreen wipers slow/fast speed.


F13



40 A

Built-in systems interface supply (ignition positive).


F14



30 A

Valvetronic supply (VTi).


F15



10 A

Right-hand main beam headlamps.


F16



10 A

Left-hand main beam headlamps.


F17



15 A

Left-hand dipped beam headlamps.


F18



15 A

Right-hand dipped beam headlamps.


F19



15 A

Oxygen sensors and electrovalves (VTi),
electrovalves (Diesel), EGR electrovalve (Diesel).


F20



10 A

Pumps, electronic thermostat (VTi), water in fuel
sensor (Diesel).


F21



5 A

Fan assembly control supply, ABS/ESP.

11
PRACTICAL INFORMATION

Table of maxi-fuses


Fuse N°



Rating


Functions



MF1 *



60 A

Fan assembly.


MF2 *



30 A

ABS/ESP pump.


MF3 *



30 A

ABS/ESP electrovalves.


MF4 *



60 A

Built-in Systems Interface (BSI) supply.


MF5 *



60 A

Built-in Systems Interface (BSI) supply.


MF6 *



-

Not used.


MF7 *



80 A

Dashboard fusebox.


MF8 *



-

Not used.

*
The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fuses must be carried out by a
CITROËN dealer or a qualifi ed workshop.

11
160
PRACTICAL INFORMATION
If the telephone is being used at
the same time on the MyWay au-
dio navigation system, it will be
interrupted after 10 minutes. A fl at battery prevents the engine
from starting (refer to the corre-
sponding paragraph).
ENERGY ECONOMY MODE

System which manages the period of
use of certain functions to conserve a
suffi cient level of charge in the battery.
After the engine has stopped, you can
still use functions such as the audio
equipment, windscreen wipers, dipped
beam headlamps, courtesy lamps, etc.
for a maximum combined period of
thirty minutes.


Switching to economy mode

Once this period has elapsed, a message ap-
pears on the multifunction screen indicating
that the vehicle has switched to economy mode
and the active functions are put on standby.
Exiting economy mode
These functions are reactivated auto-
matically the next time the vehicle is
driven.


)
In order to resume the use of these
functions immediately, start the en-
gine and let it run for a few minutes.
The time available to you will then be
double the period for which the engine is
left running. However, this period will al-
ways be between fi ve and thirty minutes.
This period may be greatly re-
duced if the battery is not fully
charged.
CHANGING A FRONT OR REARWIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
of tools.

Before removing a front wiper blade



)
Within one minute after switching off
the ignition, operate the wiper stalk
to position the wiper blades in the
vertical position.
This position must be used in order to
avoid damaging the wiper blade and the
bonnet.


Removal



)
Raise the corresponding wiper arm.

)
Unclip the wiper blade and remove it.


Fitting



)
At the front, check the size of the wip-
er blade as the shorter blade is fi tted
to the passenger side of the vehicle.

)
Put the corresponding new wiper
blade in place and clip it.

)
Fold down the wiper arm carefully.



After fitting a front wiper blade



)
Switch on the ignition.

)
Operate the wiper stalk again to
park the wiper blades.