instrument panel CITROEN C3 2023 User Guide

38
Practical information
– below mark B : top up the engine oil
immediately.
Oil grade
Before topping up or changing the engine
oil, check that the oil is suitable for the engine
and complies with the recommendations in
the service schedule supplied with the vehicle
(or available from your CITROËN dealer).
Use of non-recommended oil may invalidate
the contractual warranty in the event of
engine failure.
Topping up the engine oil level
For the location of the engine oil filler cap, please
refer to the corresponding under-bonnet engine
compartment illustration.
►

Add oil in small quantities, avoiding any spills
on engine components (risk of fire).
►


W
ait a few minutes before checking the level
again using the dipstick.
►

T
op up the level if necessary.
►

After checking the level, carefully screw the
oil filler cap back on

and replace the dipstick in
its tube.
Within 30 minutes of adding oil, the oil
level indication in the instrument panel
when the ignition is switched on is not valid.
Brake fluid
The level of this fluid should be close to
the "MAX" mark. If not, check the leakage
in the circuit and the brake pad wear.
To know how often the brake fluid should be
replaced, refer to the manufacturer's servicing
schedule.
Clean the cap before removing it to refill.
Use only DOT3 or DOT4 brake fluid from
a sealed container.
Engine coolant
It is normal to top up this fluid between
two services.
The check and top-up must only be done with
the engine cold.
A low level presents a risk of serious damage to
the engine.
The level of engine coolant should be close to
the "MAX" mark but should never exceed it.
If the level is close to or below the " MIN” mark, it
is essential to top up.
When the engine is hot, the temperature of
engine coolant is regulated by the fan.
As the cooling system is pressurised, wait at
least one hour after switching off the engine
before carrying out any work.
In order to avoid the risk of burning, if you need
to top up in an emergency, wrap a cloth around
the cap and unscrew the cap by two turns to
allow the pressure to drop.
Once the pressure has dropped, remove the cap
and top up to the required level.
Screenwash fluid
Top up to the required level when necessary.
Fluid specification
The fluid must be topped up with a ready-to-use
mixture.
In winter (temperatures below zero), a liquid
containing an agent to prevent freezing must
be used which is appropriate for the prevailing
conditions, in order to protect the elements of the
system (pump, tank, ducts, jets, etc.).
Filling with pure water is prohibited under
all circumstances (risk of freezing,
limestone deposits, etc.).

43
In the event of a breakdown
8Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does
not obstruct traffic: the ground must be level,
stable and non-slippery.
With a manual gearbox, engage first gear to
lock the wheels, apply the parking brake and
switch off the ignition.
Check for the fixed illumination of the parking
brake indicator lamps in the instrument panel.
The occupants must get out of the vehicle
and wait where they are safe.
If necessary, place a chock under the wheel
diagonally opposite the wheel to be changed.
Never go underneath a vehicle raised using a
jack; use an axle stand.
Wheel with wheel trim
When removing the wheel , first remove
the wheel trim by pulling at the valve aperture.
When refitting the wheel , refit the wheel
trim, starting by placing its aperture in line
with the valve and then pushing it into place
all round its edge with the palm of your hand.
Wheel nuts removing pattern

► Loosen the nuts on the wheel in diagonal
sequence. Do not remove wheel nuts.


► Slacken the bolts using the wheel wrench 3
only.


► Place the foot of jack 1 on the ground and
ensure that it is directly below the front A or
rear
B jacking point on the underbody, whichever
is closest to the wheel to be changed.


► Extend jack 1 with the jack handle 2 and
wheel wrench 3 until its head comes into contact
with jacking point

A
or B; contact area A or B
on the vehicle must be properly inserted into the
central part of the head of the jack.
►

Raise the vehicle until there is sufficient
space between the wheel and the ground to
admit the spare (not punctured) wheel easily

.

71
Alphabetical index
Fittings, interior 18
Flap, fuel filler
35
Flashing indicators

20, 46
Fluid, brake

38
Fluid, engine coolant

38
Folding the rear seats

15–16
Fuel

4
Fuel consumption

4
Fuel level, low

35
Fuel (tank)

35
Fusebox, dashboard

48
Fusebox, engine compartment

48, 51
Fuses

48, 51
G
Gauge, fuel 35
Gearbox, manual
32, 40
Gear lever, manual gearbox

32
Gear shift indicator

33
Glove box

18
H
Hazard warning lamps 23
Headlamps (adjustment)
20
Headlamps, dipped beam

46
Headlamps, halogen

20, 45
Headlamps, main beam

46
Heating

16
Hooks 19
Horn
23
I
Indicator, coolant temperature 7
Indicators, direction
20, 46
Indicator, service

7
Inflating tyres

40, 61
Instrument panels

5
J
Jack 42
Jump starting
56
K
Key 9–10
Key with remote control
9, 31
L
Labels, identification 60
Lamps, rear
47
LEDs - Light-emitting diodes

46–47
Level, brake fluid

38
Level, engine coolant

7, 38
Level, engine oil 37
Levels and checks
37–38
Level, screenwash fluid

21, 38
Light-emitting diodes - LEDs

46–47
Lighting, exterior

20
Lighting, interior

19
Locating your vehicle

9
Locking

9
Locking from the inside

10
Locking the doors

10
M
Maintenance (advice) 41
Maintenance, routine
39
Map reading lamps

19
Markings, identification

60
Mirrors, door

15
O
Obstacle detection 33
Oil change
37
Oil consumption

37
Oil, engine

37
On-board tools

42
Opening the bonnet

35–36
Opening the boot

11
Opening the doors

11