ESP Citroen C3 PICASSO 2008.5 1.G Owner's Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C3 PICASSO, Model: Citroen C3 PICASSO 2008.5 1.GPages: 204, PDF Size: 11 MB
Page 135 of 204
i
!
123
PRACTICAL INFORMATION CITROËN will not accept respon-
sibility for the cost incurred in re-
pairing your vehicle or for rectify-
ing malfunctions resulting from
the installation of accessories not
supplied and not recommended
by CITROËN and not installed in
accordance with its instructions,
in particular when the combined
consumption of all of the addition-
a l e q u i p m e n t c o n n e c t e d e x c e e d s
1 0 m i l l i a m p e r e s .
Installing electrical accessories
Your vehicle's electrical system is
designed to operate with standard
o r o p t i o n a l e q u i p m e n t .
Before installing other electrical
e q u i p m e n t o r a c c e s s o r i e s o n y o u r
v e h i c l e , c o n t a c t a C I T R O Ë N d e a l e r .
CHANGING A FUSE
Procedure for replacing a faulty fuse
with a new fuse to rectify a failure of the
c o r r e s p o n d i n g f u n c t i o n .
Access to the tools
The extraction pliers and the spare fuse
storage compartment are installed on
t h e b a c k o f t h e f a s c i a f u s e b o x c o v e r .
To gain access to them:
Open the glove box,
unclip the fuse access cover by pul-
ling on the side,
remove the cover completely,
r e m o v e t h e p l i e r s . Changing a fuse
Before changing a fuse, the cause of
t h e f a i l u r e m u s t b e i d e n t i fi e d a n d r e c t i -
fi e d .
Identify the faulty fuse by checking
t h e c o n d i t i o n o f i t s fi l a m e n t .
Use the special pliers to extract the
f u s e f r o m i t s h o u s i n g .
Always replace the faulty fuse with a
f u s e o f t h e s a m e r a t i n g .
Check the correspondence between
the number etched on the box, the
rating etched on the fuse and the ta-
b l e s b e l o w .
Correct Incorrect
Page 138 of 204
126
PRACTICAL INFORMATION
Engine compartment fuses
The fuse box is placed in the engine
compartment near the battery (left-hand
s i d e ) .
Access to the fuses
U n c l i p t h e c o v e r .
Change the fuse (see correspond-
i n g p a r a g r a p h ) .
W h e n y o u h a v e fi n i s h e d , c l o s e t h e
cover carefully to guarantee the
s e a l i n g o f t h e f u s e b o x . Fuse table
Fuse N° Rating Functions
F1 20 A Engine control unit supply, cooling fan unit control,
m u l t i f u n c t i o n e n g i n e c o n t r o l m a i n r e l a y .
F2 15 A H o r n .
F3 10 A F r o n t / r e a r w a s h - w i p e .
F4 20 A D a y t i m e r u n n i n g l a m p s .
F5 15 A D i e s e l h e a t e r ( d i e s e l e n g i n e ) , f u e l p u m p ( p e t r o l
e n g i n e ) .
F6 10 A ABS/ESP control unit, ABS/ESP cut-off relay,
s e c o n d a r y s t o p s w i t c h .
F7 10 A E l e c t r i c a l p o w e r s t e e r i n g .
F8 25 A S t a r t e r c o n t r o l .
F9 10 A S w i t c h i n g a n d p r o t e c t i o n u n i t .
F10 30 A D i e s e l e n g i n e i n j e c t i o n p u m p v a l v e , i n j e c t o r s a n d
i g n i t i o n c o i l s ( p e t r o l e n g i n e ) .
F11 40 A A i r c o n d i t i o n i n g b l o w e r .
Page 139 of 204
127
PRACTICAL INFORMATION
Fuse N° Rating Functions
F12 30 A W i n d s c r e e n w i p e r s s l o w / f a s t s p e e d .
F13 40 A B u i l t - i n s y s t e m s i n t e r f a c e s u p p l y ( i g n i t i o n p o s i t i v e ) .
F14 30 A V a l v e t r o n i c s u p p l y ( p e t r o l ) .
F15 10 A R i g h t - h a n d m a i n b e a m h e a d l a m p .
F16 10 A L e f t - h a n d m a i n b e a m h e a d l a m p .
F17 15 A L e f t - h a n d d i p p e d h e a d l a m p .
F18 15 A R i g h t - h a n d d i p p e d h e a d l a m p .
F19 15 A Multifunction engine control supply (petrol engine),
a i r c o o l i n g s o l e n o i d v a l v e s ( D i e s e l ) .
F20 10 A Multifunction engine control supply (petrol engine),
T u r b o p r e s s u r e r e g u l a t i o n v a l v e ( D i e s e l ) , e n g i n e
c o o l a n t l e v e l d e t e c t o r ( D i e s e l ) .
F21 5 A Fan assembly control supply, APC, ABS ESP
r e l a y s .
Page 142 of 204
i
!
!
130
PRACTICAL INFORMATION D o n o t d i s c o n n e c t t h e t e r m i n a l s
w h i l e t h e e n g i n e i s r u n n i n g .
D o n o t c h a r g e t h e b a t t e r i e s w i t h o u t
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
The batteries contain harmful sub-
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
must not, in any circumstances, be
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
Follow the instructions for use pro-
vided by the manufacturer of the
c h a r g e r .
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and con-
n e c t o r s a r e c l e a n . I f t h e y a r e c o v -
ered with sulphate (whitish or green-
ish deposit), remove them and clean
t h e m .
At the risk of discharging the bat-
tery, the deactivated functions can
b e r e a c t i v a t e d m a n u a l l y .
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions in relation to the level of
c h a r g e r e m a i n i n g i n t h e b a t t e r y .
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
c o n d i t i o n i n g , t h e r e a r s c r e e n d e - i c i n g . . .
The deactivated functions are reacti-
vated automatically as soon as condi-
t i o n s p e r m i t .
It is advisable to disconnect the
battery if the vehicle is to be left un-
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
Close the windows and the doors
b e f o r e d i s c o n n e c t i n g t h e b a t t e r y .
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit in-
i t i a l i s a t i o n o f t h e e l e c t r o n i c s y s t e m s .
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e n -
countered following this operation,
c o n t a c t a C I T R O Ë N d e a l e r .
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation
s y s t e m .
Page 143 of 204
i
!
!
130
PRACTICAL INFORMATION D o n o t d i s c o n n e c t t h e t e r m i n a l s
w h i l e t h e e n g i n e i s r u n n i n g .
D o n o t c h a r g e t h e b a t t e r i e s w i t h o u t
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
The batteries contain harmful sub-
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
must not, in any circumstances, be
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
Follow the instructions for use pro-
vided by the manufacturer of the
c h a r g e r .
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and con-
n e c t o r s a r e c l e a n . I f t h e y a r e c o v -
ered with sulphate (whitish or green-
ish deposit), remove them and clean
t h e m .
At the risk of discharging the bat-
tery, the deactivated functions can
b e r e a c t i v a t e d m a n u a l l y .
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions in relation to the level of
c h a r g e r e m a i n i n g i n t h e b a t t e r y .
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
c o n d i t i o n i n g , t h e r e a r s c r e e n d e - i c i n g . . .
The deactivated functions are reacti-
vated automatically as soon as condi-
t i o n s p e r m i t .
It is advisable to disconnect the
battery if the vehicle is to be left un-
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
Close the windows and the doors
b e f o r e d i s c o n n e c t i n g t h e b a t t e r y .
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit in-
i t i a l i s a t i o n o f t h e e l e c t r o n i c s y s t e m s .
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e n -
countered following this operation,
c o n t a c t a C I T R O Ë N d e a l e r .
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation
s y s t e m .
Page 144 of 204
i
!
131
PRACTICAL INFORMATION
A fl a t b a t t e r y p r e v e n t s t h e e n g i n e
from starting (refer to the corre-
s p o n d i n g p a r a g r a p h ) .
If the telephone is being used at
the same time with the MyWay au-
dio navigation, it will be interrupted
a f t e r 1 0 m i n u t e s .
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
s u f fi c i e n t l e v e l o f c h a r g e i n t h e b a t t e r y .
After the engine has stopped, you can
still use functions such as the audio
e q u i p m e n t , w i n d s c r e e n w i p e r s , d i p p e d
h e a d l a m p s , c o u r t e s y l i g h t s , e t c . f o r a
maximum combined duration of thirty
m i n u t e s . Exiting economy mode
These functions are reactivated auto-
m a t i c a l l y n e x t t i m e t h e v e h i c l e i s d r i v e n .
In order to resume the use of these
functions immediately, start the en-
g i n e a n d l e t i t r u n f o r a f e w m i n u t e s .
The time available to you will then be
double the duration for which the en-
g i n e i s l e f t r u n n i n g . H o w e v e r , t h i s p e r i o d
w i l l a l w a y s b e b e t w e e n fi v e a n d t h i r t y
m i n u t e s .
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multifunction
display indicating that the vehicle has
switched to economy mode and the ac-
t i v e f u n c t i o n s a r e p u t o n s t a n d b y .
CHANGING A WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
o f t o o l s .
Removing a front or rear wiper
blade
R a i s e t h e c o r r e s p o n d i n g w i p e r a r m .
U n c l i p t h e w i p e r b l a d e a n d r e m o v e i t .
Fitting a front or rear wiper blade
At the front, check the size of the
wiper blade as the shorter blade is
fi t t e d o n t h e r i g h t - h a n d s i d e o f t h e
v e h i c l e .
Put the corresponding new wiper
b l a d e i n p l a c e a n d c l i p i t .
F o l d d o w n t h e w i p e r a r m c a r e f u l l y .
Before removing a front wiper blade
Within one minute after switching off
the ignition, operate the wipers stalk
to position the wiper blades in the
v e r t i c a l p o s i t i o n .
This position must be used in order to
avoid damaging the wiper blade and the
b o n n e t .
After fitting a front wiper blade
S w i t c h o n t h e i g n i t i o n .
Operate the wipers stalk again to
p a r k t h e w i p e r b l a d e s .
Page 192 of 204
179
1 1
2 2
3 3
1 1
2 2
4 4
1 1
H A N D S - F R E E K I T *
F o r s a f e t y r e a s o n s a n d b e c a u s e t h e y r e q u i r e p r o l o n g e d a t t e n t i o n o n t h e p a r t o f t h e d r i v e r , t h e o p e r a t i o n s f o r m a t c h i n g o f t h e B l u e t o o t h mobile telephone with your Audio system hands-free kit must be c a r r i e d o u t w i t h t h e v e h i c l e s t a t i o n a r y a n d t h e i g n i t i o n o n .
Select the accessory which corresponds to the n a m e o f t h e v e h i c l e , a s u p e r i m p o s e d c o n fi g u r a t i o n display appears on the multifunction display.
Activate the telephone’s Bluetooth function and carry out a search of the Bluetooth accessories present for the telephone.
S e l e c t t h e Y E S t a b o n t h e d i s p l a y u s i n g t h e b u t t o n s t h e n c o n fi r m b y p r e s s i n g O K .
E n t e r t h e v e h i c l e ’ s a u t h e n t i c a t i o n c o d e ( = 1 2 3 4 ) . D e p e n d i n g o n t h e t e l e p h o n e , y o u m a y b e a s k e d to enter this code before the superimposed c o n fi g u r a t i o n d i s p l a y a p p e a r s .
Y E S
Y E S
The services offered by the hands-free kit depend on the network, the SIM card and the compatibility of the Bluetooth equipment used. C o n s u l t y o u r t e l e p h o n e ’ s m a n u a l a n d y o u r o p e r a t o r t o fi n d o u t w h i c h s e r v i c e s a r e a v a i l a b l e t o y o u . A l i s t o f m o b i l e t e l e p h o n e s w h i c h o f f e r t h e b e s t r a n g e o f s e r v i c e s i s a v a i l a b l e f r o m t h e n e t w o r k . Consult a CITROËN dealer.
R E C E I V I N G A C A L L
A n i n c o m i n g c a l l i s a n n o u n c e d b y a r i n g a n d a s u p e r i m p o s e d d i s p l a y on the multifunction display.
Select the YES tab on the display u s i n g t h e b u t t o n s a n d c o n fi r m b y p r e s s i n g O K .
P r e s s t h e e n d o f t h e s t e e r i n g w h e e l s t a l k t o a c c e p t the call.
P r e s s t h e e n d o f t h e s t e e r i n g w h e e l s t a l k f o r m o r e than two seconds to access your directory.
To dial a number, use the keypad on your telephone.
M A K I N G A C A L L
M A T C H I N G A T E L E P H O N E
D I S P L A Y C
T h e T E L E P H O N E m e n u p e r m i t s a c c e s s t o t h e f o l l o w i n g f u n c t i o n s i n p a r t i c u l a r : P h o n e b o o k , C a l l l i s t , M a t c h i n g m a n a g e m e n t . * a c c o r d i n g t o a v a i l a b i l i t y o n t h e v e h i c l e .