display Citroen C3 PICASSO RHD 2012.5 1.G Owner's Guide

2
Multifunction screens
45
Tr i p c o m p u t e r
)Press the button, located at the end of the
wiper stalk, to display the various items of
trip computer information in succession.The trip computer provides the
following information:
S
ystem that gives you information on the journey in progress (range, fuel consumption…).
Monochrome screen A


Information displays
- range,
- current
fuel consumption,
-
Stop & Start time counter,
- distance travelled,
- avera
ge fuel consumption,
)
The next press then returns you to thenormal display.
- average speed.

Zero reset
)
Press the control for more than
two seconds to reset to zero the distance
travelled, the average fuel consumption
and the average speed.

Multifunction screens
46
- the current information
tab with:
●
the range,
●
th
e current fuel consumption,
●
the distance remaining to be travelled or the Stop &Start time counter,
Monochrome screen C


Information displays
)
Press the button, located at the end of
the wiper stalk, to display the various tripcomputer tabs in succession:
- the trip
"1"tab with:
●
the distance travelled,
●
the avera
ge fuelconsumption,
●
the average speed,for the first trip.

- the tri
p "2"tab with:


●
the distance travelled,

●
the avera
ge fuel
consumption,

●
the average speed, for the second trip.
)Pressing the button again returns you to
the normal display.

Trip zero reset
)When the trip required is displayed, press
the button on the end of the wiper stalk for
more than two seconds.
Trips "1"
and "2"are independent but their useis identical.
For example, trip "1"
can be used for daily figures, and trip "2"
for monthly figures.

2
Multifunction screens
47





Tr ip computer, a few definitions


When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
Range
(miles or km)The distance which can still be
travelled with the fuel remainingin the tank. Related to theaverage fuel consumption over
the last few miles (kilometres)travelled.


Current fuel consumption
(mpg or l/100 km or km/l)
Calculated over the last few seconds.


Average fuel consumption
(mpg or l/100 km or km/l)
Calculated since the last trip
computer reset.


Distance travelled
(miles or km)
Calculated since the last tripcomputer reset.
Average speed
(mph or km/h)Calculated since the last trip computer reset.
Distance remaining todestination
(miles or km)This is the distance remaining to be
travelled to the final destination. It
is either calculated instantly by the
navigation system, if guidance isactivated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.

Stop & Start time counter
(minutes / seconds or hours / minutes)
If your vehicle is fitted with Stop & Star t, a time counter calculates the
time spent in STOP mode during a journey.
It resets to zero ever
y time theignition is switched on with the key.

If dashes are displayed continuouslywhile driving in place of the digits, contact a CITROËN dealer or aqualified workshop.


This value may vary following a changein the style of driving or the relief,resulting in a significant change in thecurrent fuel consumption.
This function is only displayed from 20 mph (30 km/h).

3
Comfort
53
The air conditioning only operates when the engine is running.
The driver and
front passenger can
each adjust the temperature to their
requirements.
)Turn control 2 or 3
to the left or to the right respectively to decrease or increase this value.
A setting around the value 21 provides
optimum comfor t. However, depending on your requirements, a setting between 18 and 24 isnormal.
You are advised to avoid a left / right settingdifference of more than 3.
Automatic operation
)Press the "AUTO"button. The indicator lamp in the button comes on.
2. Driver's side adjustment






Dual-zone digital air conditioning
We recommend the use of this mode: it permitsautomatic and optimised adjustment of all
of the functions, passenger compartment
temperature, air flow, air distribution and air
recirculation, in accordance with the comfort
value that you have chosen.
This system is designed to operate effectively in all seasons, with the windows closed. The value indicated on the displa
y corresponds
to a level of comfor t and not to a temperature in
de
grees Celsius or Fahrenheit.
1. Automatic comfort programme
3. Passen
ger's side adjustment
On entering the vehicle, if the interior temperature is much colder or warmer than the comfort value, there is noneed to change the value displayed in order to obtain the comfort required. The system corrects the difference in temperature automatically and asquickly as possible.
When the engine is cold, to prevent too great a distribution of cold air, the air flow will reach its optimum levelgradually. In cold weather, it favours the distribution of warm air to thewindscreen, side windows and footwells only.

Comfort
54
programme
The automatic comfor t programme
may not be sufficient to quicklydemist or defrost the windscreen
and side windows
(humidity, several
passengers, ice, etc.).
)To switch the system off, press this buttonagain or on "AUTO"
. The indicator lamp in
the button goes off and the indicator lamp in the "AUTO"
button comes on.
With Stop & Start, when demisting hasbeen activated, the STOP mode is notavailable.
)Press this button to activate the automatic
visibility programme. The indicator lamp in
the button comes on. The system automatically controls the air conditioning, the air flow and the air intake andprovides optimum distribution of the ventilation
to the windscreen and side windows. I
f you wish, you can make a different choice
from that offered by the system by changing
a setting. The other functions will still be controlled automatically.) Pressing the "AUTO"
button returns thesystem to completely automatic operation.
For maximum cooling or heating of the passenger compar tment, it is possible to exceed the minimum value 14 or the maximum value 28.)Turn control 2
or 3
to the left until "LO"
is displayed or to the right until "HI"is displayed.


Manual operation
)
Press this button to switch off
the air conditioning.

5. Air conditioning On / Off

Switching the system off could result in
discomfort (humidity, condensation).)Press this button again to return to automatic operation of the air conditioning.The indicator lamp in the "A/C"
buttoncomes on.

5
Visibility
79














Lighting controls System for selection and control of the various front and rear lamps providing the vehicle's lighting.


Main lighting

The various front and rear lamps of the vehicle
are designed to adapt the driver's visibilityprogressively according to climatic conditions:


- sidelamps, to be seen,

- dipped beam headlamps to see without
dazzlin
g other drivers,

- main beam headlamps to see clearly when
the road is clear.



Additional lighting
Other lamps are installed to fulfil the
requirements of par ticular conditions of
visibility:


- a rear foglamp to be seen from afar,

- front foglamps for even better forward
vision.

Programming

Various automatic lighting control modes
are also available according to the following
options:


-
guide-me-home lighting,

- automatic illumination of headlamps.

Model without AUTO lighting


Model with AUTO li
ghting

Automatic illumination of headlamps.


Manual controls

The lighting is controlled directly by the driver
by means of the ring A
and the stalk B
.
A.Main lighting mode selection ring: turn it
to position the symbol required facing themark.
Li
ghting off / daytime running lamps.
Sidelamps.
B
.Stalk for switching headlamps: pull the stalk
towards you to switch the lighting betweendipped and main beam headlamps.
In the lamps off and sidelamps modes, the driver can switch on the main beam headlamps temporarily ("headlamp flash") by maintaining a pull on the stalk.

Dipped headlamps or main beam headlamps.


Displays

Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.

Visibility
82

Linked with the Guide-me-home
lighting
Association with the automatic illumination
of headlamps provides the guide-me-home lighting with the following additional options:


- automatic activation of guide-me-home lighting when automatic illumination of
headlamps is switched on (in the vehicle
parameters of the multifunction screen configuration menu),

- selection of the duration of maintaining of
the lighting for 15, 30 or 60 seconds in the
vehicle parameters of the multifunction
screen configuration menu (except for monochrome screen A where this is
preset).



Operating fault

In the event of a malfunction of the sunshine sensor, the lamps comeon, this warning lamp is displayed
in the instrument panel and/or a message appears
in the multifunction screen, accompanied by an audible signal.
Contact a CITROËN dealer or a qualified workshop.

In fog or snow, the sunshine sensor maydetect sufficient light. Therefore, the lamps will not come on automatically.
Do not cover the sunshine sensor,linked with the rain sensor and located in the centre of the windscreen behindthe rear view mirror; the associatedfunctions would no longer be controlled.

Automatic illumination of headlamps
The sidelamps and dipped beam headlamps areswitched on automatically, without any action on
the par t of the driver, when a low level of external
li
ght is detected or in certain cases of activation
of the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
off, the lamps are switched off automatically.
Activation
)Turn ring Ato the A"AU TO "
position. The automatic
illumination of headlamps is accompanied by amessage in the multifunction screen.
Deactivation
)Turn ring A
to a position other
than "AUTO". Deactivation is accompanied
b
y a message in the multifunction screen.

8
Safety
117

Seat belt not fastened / unfastened warning lamp Fastenin
g
) Pull the strap, then inser t the tongue in thebuckle. )
Check that the seat belt is fastened correctly by pulling the strap.



Height adjustment
)
To lower the attachment point, squeeze the control A
and slide it downwards.)
To raise the attachment point, slide thecontrol A
upwards.
When the ignition is switched on, this warning lamp comes on, either on theinstrument panel or on the seat belt andpassenger's front airbag warning lamp
display, if the driver and/or the frontpassenger has not fastened their seat belt.
Unfastening
) Press the red button on the buckle. )
Guide the seat belt as it rolls up.


Seat belts


Front seat belts


The front seat belts are fitted with apretensioning and force limiting system.
This s
ystem improves safety in the frontseats in the event of a front or side impact.
Depending on the severity of the impact, thepretensioning system instantly tightens the seat
belts against the body of the occupants.
The pretensioning seat belts are active when
the ignition is on.
The
force limiter reduces the pressure of the seat belt on the chest of the occupant, so
improving their protection.
From approximately 12 mph (20 km/h) this warninglamp flashes for two minutes accompanied by an audible signal. Once these two minutes have
elapsed, this warning lamp remains on until the driver and/or the front passenger fastens their seat belt.

Safety
118
Seat belt not fastened / unfastened warning lamp display
1. Front and/or rear seat belts not fastened / unfastened warning lamp. 2.
Front left seat belt warning lamp. 3.Front right seat belt warning lamp. 4.
Rear right seat belt warning lamp. 5.
Rear centre seat belt warning lamp.
6.Rear left seat belt warning lamp.


Rear seat belts

The rear seats are each fitted with a three-point
iner tia reel seat belt with force limiter (with the exception of the rear centre seat).

Locking
When the rear side side belts are not being used, you can lock them in place. To do so:)
Raise the grip Ato its maximum height.



Fastening
)
Pull the strap, then inser t the tongue in the buckle. )
Check that the seat belt is fastened correctly by pulling the strap.


Unfastening
)
Press the red button on the buckle. )
Guide the seat belt as it rolls up.

The correspondin
g warning lamp 2 or 3
comes
on in red on the seat belt and passenger's front airbag warning lamp display if the seat belt isnot fastened or is unfastened.



Seat belt unfastened warninglamp

This warning lamp comes on,either on the instrument panel or
on the seat belt and passenger's
front airbag warning lamp display, when one or more rear passengers unfasten their seat belt.
From approximatel
y 12 mph (20 km/h),
this warning lamp flashes for two minutes
accompanied by an audible signal of increasingvolume. Once these two minutes have elapsed,
this warning lamp remains on until the one or more rear passengers fasten their seat belt.

8
Safety
119
2 nd row rear centre seat
belt


Removal and storing
)
Press the red button on the buckle B, then on the buckle A.)
Guide the strap as it rolls up and bring the
tongue B , then A
onto the magnet of the
attachment point on the roof.
Installation
) Pull the strap and inser t the tongue A
in the left-hand buckle.)
Inser t the tongue Bin the right-hand buckle. )
Check the fastening of each buckle by
pulling the strap. Th
e seat belt for the rear centre seat of the 2 nd row is incorporated at the rear left of the roof.


Seat belt unfastened warninglamp display
When the ignition is switched on, thecorresponding warning lamps 4 , 5and 6
come
on in red for approximately 30 seconds, if the seat belt is not fastened.
When the en
gine is running or the vehicle ismoving, the corresponding warning lamp 4 , 5or 6
comes on in red, accompanied by an audiblesignal and a message on the multifunction screen, if a rear passenger has unfastened their seat belt.