steering torque Citroen C3 PLURIEL 2004 1.G Workshop Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2004, Model line: C3 PLURIEL, Model: Citroen C3 PLURIEL 2004 1.GPages: 523, PDF Size: 10.32 MB
Page 208 of 523
![Citroen C3 PLURIEL 2004 1.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine 204
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper](/img/9/4135/w960_4135-207.png "Citroen C3 PLURIEL 2004 1.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine 204
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper")
Downloaded from www.Manualslib.com manuals search engine 204
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper timing cover
(12).
The lower timing cover (11).
The accessories drive pulley (9).
The screw (10).
Tightening torqueScrew (10)Pre tighten to:3 ± 0,3 m.daN.
Angular tighten:180°±5°.
Remove tool [1].
Refit:
The engine support
(8), tighten to 5,5 ± 0,4 m.daN.
The engine support (4), tighten to 6,1 ±0,6 m.daN.
The engine support (5), tighten to 2,5 ±0,2 m.daN.
The electrical harness (7).
The power steering fluid reservoir (6).
XSARA PICASSO
Couple:
The tube (2).
The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
The fuel unions (1).
The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
The accessories drive belt
(see corresponding operation).
The front RH splash shield
(see corresponding operation).
The front RH wheel, tighten to 9 ±1 m.daN.
Reconnect the positive and negative terminals of the battery.
IMPERATIVE:Perform the operations that are necessary following a
reconnection of the battery (see corresponding operation).
Page 214 of 523
![Citroen C3 PLURIEL 2004 1.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine 210
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting (continued).
Refit tool [1]at «b».
Remove the screw (10).
Refit:](/img/9/4135/w960_4135-213.png "Citroen C3 PLURIEL 2004 1.G Workshop Manual Downloaded from www.Manualslib.com manuals search engine 210
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting (continued).
Refit tool [1]at «b».
Remove the screw (10).
Refit:")
Downloaded from www.Manualslib.com manuals search engine 210
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refitting (continued).
Refit tool [1]at «b».
Remove the screw (10).
Refit:
The upper timing cover
(12).
The lower timing cover (11).
The accessories drive pulley (9).
The screw (10).
Tightening torqueScrew (10)Pre tighten to:3 ± 0,3 m.daN.
Angular tighten:180°±5°.
Remove tool [1].
Refit:
The engine support
(8), tighten to5,5 ± 0,4 m.daN.
The engine support (4), tighten to 6,1 ±0,6 m.daN.
The engine support (5), tighten to 2,5 ±0,2 m.daN.
The electrical harness (7).
The power steering fluid reservoir (6).
XSARA PICASSO
Disengage the jack from under the engine.
Couple:
The tube
(2).
The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
The fuel unions (1).
The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
The accessories drive belt
(see corresponding operation).
The front RH splash shield (see corresponding operation).
The front RH wheel, tighten to 9 ± 1 m.daN.
Reconnect the positive and negative terminals of the battery.
IMPERATIVE: Perform the operations that are necessary following a
reconnection of the battery (see corresponding operation).
Page 224 of 523
Downloaded from www.Manualslib.com manuals search engine 220
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Remove:
The fixings of the pipe linking the power steering pump with the rotary valve.
The clutch lower closing plate.
Lock the engine flywheel, using tool
[6].
Remove the screw (8).
Refit the screw (8)without its thrust washer.
Remove:
The accessories pulley
(9), using tool[8].
Tool [6].
The lower torque reaction rod.
Support the engine by means of a workshop hoist.
Remove:
The bearing shell fitting
(10).
The nut (12).
Screws (11).
The bracket (13).
NOTE:Lift then lower the engine with the workshop hoist, to have access to the
timing cover fixing screws.
Remove:
The intermediate timing cover.
The lower timing cover.
B1CP04BCB1BP2R3CB1BP2R4C
XSARA XSARA PICASSO
Page 362 of 523
Downloaded from www.Manualslib.com manuals search engine 358
AXLES
SUSPENSION
STEERING
FRONT AXLE
Tightening torques (m.daN).
(1)Nut fixing suspension leg on body: 6,5 ± 0,6
(2)Damper:
(3)Anti roll bar link rod upper ball joint:3,2 ± 0,3
(4)Suspension leg pivot: 5,4 ± 0,5
(5)Anti roll bar link rod lower ball joint: 3,2 ± 0,3
(6) Anti roll bar bearing fixing on subframe:8 ± 0,8
(7)Hub nut: 24,5 ± 0,5
(8)Wheel bolt:9 ±1
(9)Subframe to bodyshell fixing screw:10 ± 1
(10) Anti roll bar:
(11)Pivot lower ball joint fixing on lower arm: 5,5 ± 0,5
(12)Pivot lower ball joint fixing: 4 ± 0,4
(13)Lower arm front and rear mounting fixing: 14 ± 0,4
(14)Stabiliser bar screw:6,6 ±0,7
(15)Steering ball joint fixing:3,5 ± 0,3
Private vehicles Anti roll bar
EuropeDiameter (mm)Colour
HFX KFV 18Violet
NFU 20 Green
8HX19Blue
Entreprise vehiclesDiameter (mm)Colour
HFX 8HX18 Violet
CRD vehicles Diameter (mm) Colour
KFV 8HX18 Violet
NFU 20 Green
B3CP07RP
C2
Page 363 of 523
Downloaded from www.Manualslib.com manuals search engine 359
AXLES
SUSPENSION
STEERING
REAR AXLE
Tightening torques (m.daN).
(25) Rear axle fixing screw: 10 ± 1
(26)Anti roll bar:
(27)Rear axle crossmember:
(28)Rear suspension arm silentblock yoke:
(29)Rear suspension arm silentblock:
(30)Yoke / suspension arm fixing screw:7 ± 0,5
(31)Rear suspension arm:
(32)Stub axle bearing nut: 20 ± 2
(33)Damper:
(34)Damper upper fixing:4,5 ± 0,4
(35) Damper lower fixing: 9,3 ± 0,9
(36)Suspension springs:
(37)Travel stop:
(38)Secondary brake cable guide support:
Private vehicles Anti roll bar
Europe
Diameter (mm)
HFX KFV20,5
(tubular)
8HX 23,5 (tubular)
NFU 25 (solid)
Vehicle entreprise Diameter (mm)
8HX 20,5
(tubular)
CRD vehiclesDiameter (mm)
8HX 20,5
(tubular)
NFU 25,5 (tubular)B3DP09UP
C2
Page 365 of 523
Downloaded from www.Manualslib.com manuals search engine 361
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV NFU 8HX
Steering column
Tightening torques (m.daN.).
(1)
Steering wheel fixing:2 ±0,3
(2)
Steering column fixing on support:2,2 ± 0,5
(3)
Steering cardan fixing: 2,2 ± 0,2Identification.
Identified by the colour of the ring at «a».
Left hand drive
:BLUE ring.
Right hand drive
: WHITE ring.
B3EP13GDB3EP13HC
C2
Page 366 of 523
Downloaded from www.Manualslib.com manuals search engine 362
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV NFU 8HX
Steering mechanism
Tightening torques (m.daN.).
(4)
Ball joint fixing on pivot:3,5 ± 0,3
(5)
Steering rod lock nut: 5 ± 0,5
(8)
Threaded washer
(9)Stud: 0,8 ± 0,1
(10)
Flat washers
(11)Fixing of mechanism on subframe:8 ± 0,8
Connectors.
(6)
Supply of electric assistance motor
(7)Torque sensor signals
HFX KFV 8HXNFU
Electric motor 60 A 65 A
Steering rack travel2x722x64
Steering ratio45,6/1
Number of rotations of
steering wheel 3,22,8
Inner angle of lock 38° 32°30’
Outer angle of lock 32°24’ 28°42’
B3EP13JD
C2
Page 367 of 523
Downloaded from www.Manualslib.com manuals search engine 363
AXLES
SUSPENSION
STEERING
FEATURES OF ELECTRIC POWER STEERING
Engines: HFX KFV NFU 8HX
Steering assistance
Supplier:KOYO.
The steering assistance is rpovided by the assistance motor
(12),
controlled by the ECU.
Power delivered to the assistance motor
(12)depends on:
Speed of the vehicle.
Torque applied on the steering wheel.Only one ECU version, whatever the engine type.
The electric power steering ECU is linked to the following connectors:
(6)Assistance motor supply.
(13)Electric power steering ECU supply.
(14)Control signals.
After changing the electric power steering ECU, it is necessary to
perform a configuration.
B3EP13KCB3EP13LC
C2
Electric power steering ECU
Page 375 of 523
Downloaded from www.Manualslib.com manuals search engine 371
AXLES
SUSPENSION
STEERING
FRONT AXLE
Tightening torques (m.daN).
(1)Nut fixing suspension leg on body: 6,5 ± 0,6
(2)Suspension leg:
(3)Anti roll bar link rod upper ball joint: 3,2 ± 0,3
(4)Suspension leg pivot: 5,4 ± 0,5
(5)Anti roll bar link rod lower ball joint: 3,2 ± 0,3
(6)Anti roll bar bearing fixing on subframe:8 ± 0,8
(7) Hub nut: 24,5 ± 0,5
(8)Wheel bolt:9 ±1
(9)Subframe to bodyshell fixing screw:10 ± 1
(10)Anti roll bar:
(11) Pivot lower ball joint fixing on lower arm: 5,5 ± 0,5
(12)Pivot lower ball joint fixing: 4 ± 0,4
(13)Lower arm front and rear mounting fixing:14 ±0,4
(14)Stabiliser bar screw: 6,6 ± 0,7
(15)Steering ball joint fixing:3,5 ± 0,3
Anti roll bar
Diameter (mm) Colour
HFX KFV
C3KFU NFU 8HX19Blue
8HW 8HV 8HY
C3
Pluriel KFV NFU 8HX 20 Green
B3CP07RP
C3 C3 PLURIEL
Page 376 of 523
Downloaded from www.Manualslib.com manuals search engine 372
AXLES
SUSPENSION
STEERING
REAR AXLE
Tightening torques (m.daN).
(1)
Rear axle fixing screw: 10 ± 1
(2)Anti roll bar:
(3)Rear axle crossmember:
(4)Rear suspension arm rubber mounting yoke:
(5)Rear suspension arm rubber mounting:
(6)Yoke / suspension arm fixing screw: 7,6 ± 0,5
(7)Rear suspension arm:
(8)Stub axle bearing nut: 20 ± 2 greased
(9) Damper:
(10)Damper upper fixing: 4,5 ± 0,4
(11)Damper lower fixing: 9,3 ± 1
(12)Suspension spring:
(13)Travel stop:
(14)Secondary brake cable guide and its support:
Anti roll bar
Diameter (mm)
HFX KFV
C3KFU NFU 8HX25,5
(tubular)
8HW 8HV 8HY
C3
PlurielKFV NFU 8HX26
(tubular)
B3CP0AFP
C3 C3 PLURIEL