oil pressure Citroen C4 2005 2.G User Guide

Downloaded from www.Manualslib.com manuals search engine 144
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
22 Oil pressure switch 2 ± 0,2
Oil filter support (*)
23Tightening1 ± 0,1
Tightening2 ± 0,2
24 Oil filter cover 2,5 ± 0,5
Engine: RHR
B1CP0GPPB1FP062C
(*) (23) Sequence of tightening
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 144

Downloaded from www.Manualslib.com manuals search engine 244
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Checking and setting the timing (continued).
Turn the engine in the normal direction of rotation until the peg [1]engages in the setting hole.
Peg the flywheel at «b», using tool [1].
Move aside the electrical harness (6).
Remove:
- The engine support (7).
- The screw (8).
- The accessories drive pulley (9).
- The lower timing cover (10).
- The upper timing cover (11).
- The tool [1].
Refit the screw (8).
Rotate the crankshaft to bring the camshaft to its pegging point.
Peg:
- The camshaft at «c», using tool [2]
(oil the pegs).
- The fuel high pressure pump pulley (15)at «f»using a 5 mmdiameter peg.
WARNING: Do not touch or damage the track of the engine speed sensor target (14).
B1BP305C
B1EP1HJD
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 244

Downloaded from www.Manualslib.com manuals search engine ENGINE
279
C4CHECKING THE OIL PRESSURE
Petrol Diesel
Engine type KFU NFU RFJ RFN RFK 9HX 9HY 9HZ RHR
Temperature (°C) 90° 80°
Pressure (bars) 1,5 3 1,3 1,9
Rpm1000
Pressure (bars) 3 5,6 4
Rpm 2000 2000 2000
Pressure (bars) 5 6,3
Rpm 3000 3000
Pressure (bars) 43,5
Rpm 40004000
Tools (Toolkit 4103)
2279-T.Bis X X X X X X X X X
4103-T X X X X X X X X X
(-).0710.F1 X
(-).0710.B1 X
(-).1503.JXX X
4103-T.B X X
7001-T X X X X X
4202-T X X
NOTE: The oil pressure should be checked with the engine hot, after the oil level has been checked.
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 279

Downloaded from www.Manualslib.com manuals search engine 280
ENGINECHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA
Engine type KFW NFU RFN 8HZ 8HX WJY RHY RHZ
Temperature (°C) 90°C
Pressure (bars) 1,5 1,3 1,8 2
Rpm 1000 1000
Pressure (bars) 3
Rpm 2000
Pressure (bars) 4
Rpm 3000
Pressure (bars) 5,1 3,5 4,5 4
Rpm4000
Tools (Toolkit 4103-T)
2279-T.Bis X X X X X X X
4103-T X X X X X X X
4202-T X X X
1503-JX
3099-TX
7017-T.X23X
NOTE: The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 280

Downloaded from www.Manualslib.com manuals search engine 281
ENGINE
CHECKING THE OIL PRESSURE
To be read with the Petrol and Diesel correspondence tables
XSARA PICASSO
Engine type NFV 6FZ RFN 9HZ 9HY RHY
Temperature (°C) 90°C 80°C 90°C
Pressure (bars) 3,3 1,5 1,3 2
Rpm 1000
Pressure (bars) 3
Rpm 2000
Pressure (bars) 5
Rpm 3000
Pressure (bars) 4 6,3 3,5 4
Rpm 4000 4000
Tools (Toolkit 4103-T)
2279-T.Bis X X X X X X
4103-T X X X X X X
7001-T X
4202-T X X X
1503-J X X
NOTE: The oil pressure should be checked with the engine hot, after the oil level has been checked.
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 281

Downloaded from www.Manualslib.com manuals search engine 347
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: AL4 AUTOMATIC GEARBOX
Engines: NFU - RFJ
B2CP3EDD
B2CP3X7D
Tightening torques (m.daN).
(1) Fixing of the electrovalve for modulation of the flow
of oil into the exchanger (EPDE): 1 ± 0,2
(2)Heat exchanger fixing: 5 ± 1
(3) Output speed sensor fixing
(4)Output speed sensor fixing: 1 ± 0,2
(5)Oil overflow and drain fixing(X = 48 mm)
: 0,9 ± 0,2
(6)Oil level plug: 3,3 ± 0,5
(7)Oil pressure sensor fixing: 0,8 ± 0,1
C4 - XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 347

Downloaded from www.Manualslib.com manuals search engine 429
AIR
CONDITIONING
ESSENTIAL: The compressor lubricant is extremely hygroscopic; always use FRESH oil.
Checking the compressor oil level
There are three specific cases:
- 1/Repairs to a system without leaks.
- 2/Slow leak.
- 3/Fast leak.
1/ Repairing a system without leaks.
a) - Using draining/recovery equipment not fitted with an oil decanter.
- Drain the system as slowly as possible via the LOW PRESSUREvalve, so as not to lose any oil.
- No more oil should be added when filling the system with R 134.afluid.
b) - Using draining/filling equipment fitted with an oil decanter.
- Drain the R 134.afluid from the system in accordance with the instructions in the equipment handbook.
- Measure the amount of oil recovered.
- Add the same amount of NEWoil when filling the system with R 134.afluid.
c) - Replacing a compressor.
- Remove the old compressor, drain it and measure the oil quantity.
- Drain the new compressor
(supplied full), so that the same amount of NEWoil is left in the compressor as was in the old compressor.
- No more oil should be added when filling the system with R 134.a fluid.
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Compressor lubricant
Angl.-t2-page428-456-2005 9/01/06 10:25 Page 429

Downloaded from www.Manualslib.com manuals search engine 430
AIR
CONDITIONING
Checking the compressor oil level (continued)
2/ Slow leak.
Slow leaks do not lead to oil loss, therefore the same procedure should be followed as if there was no leak at all.
3/ Fast leak.
This type of leak causes both oil loss as well as allowing air to enter the system.
It is therefore necessary to:
- Replace the dehydrator.
- Drain as much oil as possible
(when replacing the faulty component).
Either before or during filling of the system with R 134.afluid, introduce 80 ccof NEWoil into the circuit.
When changing one of the following components, add the quantity stated:
- A drying bottle : 15 ccof compressor oil.
- A condenser or an evaporator : 20 ccof compressor oil.
- High pressure or low pressure pipework : 5 ccof compressor oil.
- A drying cartridge : 15 ccof compressor oil.
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Angl.-t2-page428-456-2005 9/01/06 10:25 Page 430