Anti roll bar Citroen C4 2005 2.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 365
AXLES
SUSPENSION
STEERING
C4TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).
(1)Nut fixing suspension leg on body: 6,9 ± 0,6
(2) Nut fixing upper damper cup: 6,9 ± 0,6
(3)Upper fixing of anti-roll bar rod: 3,6 ± 0,3
(4)Lower fixing of anti-roll bar rod: 3,6 ± 0,3
(5)Nut fixing pivot lower ball-joint: 4,2 ± 0,4
(6)Fixing of pivot lower ball-joint on pivot: 23 ± 2,3
(7)Hub nut: 32,5 ± 2,6
(8)Steering ball-joint on pivot: 3,5 ± 0,3
(9)Fixing of suspension leg on pivot: 9 ± 0,9
Anti-roll bars
Engines Diameter (mm) Colour
ET3J4 TU5JP - EW10A/J4
DV621.5 Pink
EW10J4S DW10BTED4 22 White
B3BP18ZP
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 365

Downloaded from www.Manualslib.com manuals search engine 366
AXLES
SUSPENSION
STEERING
C4TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).
(10)Fixing of subframe extension on body: 5,1 ± 1,2
(11)Fixing of tie-rod on body: 1,8 ± 0,4
(12)Tie-rod screw on front subframe: 9,8 ± 0,9
(13) Fixing of anti-roll bar bearing on subframe: 10,4 ± 1
(14)Fixing of lower suspension arm on subframe: 11,1 ± 1
(15)Fixing of subframe extension on body: 8,5 ± 0,8
(16)Fixing of steering mechanism on subframe: 8 ± 0,8
B3CP08TD
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 366

Downloaded from www.Manualslib.com manuals search engine 367
AXLES
SUSPENSION
STEERING
C4TIGHTENING TORQUES: REAR AXLE
Tightening torques (m.daN).
(17)Damper upper fixing: 5,8 ± 0,5
(18)Fixing of yoke on rear axle: 7,6 ± 0,7
(19)Fixing of rear axle yoke on body: 6,2 ± 0,6
(20)Stub axle bearing nut
- Pre-tightening : 9 ± 0,9
- Angular tightening: 29° ± 5°
(21) Damper lower fixing: 6 ± 0,6
(22)Fixing of stub axle carrier on rear axle: 6,3 ± 0,6
Anti-roll bars
Diameter (mm)Thickness of the
Engines
(interior x exterior)crossmember panel
(mm)
ET3J4 TU5JP4 EW10A/J4
DV621x27 5
EW10J4S 24x30
6
DW10BTED4 21x27
B3DP0BDD
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 367

Downloaded from www.Manualslib.com manuals search engine 379
AXLES
SUSPENSION
STEERING
XSARA
AXLE GEOMETRY
a = Angle which defines the tracking between the front and rear axles.
Its value must not exceed12'.
Anti-roll bars
Engine versions Diameter Colour ref.
ALL TYPESSaloon 19 Blue
Estate 20 Yellow
B3CP04UC
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 379

Downloaded from www.Manualslib.com manuals search engine 380
AXLES
SUSPENSION
STEERING
XSARA TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).
(1)Damper nut: 4,5 ± 0,4
(2)Cup screw: 2,5 ± 0,3
(3)Suspension leg
(4)Anti-roll bar link rod upper ball-joint: 3,7 ± 0,3
(5)Suspension leg pivot
(hollow pivot): 4,5 ± 0,5
(5)Suspension leg pivot (pivot «H»): 5,5 ± 0,5
(6)Anti-roll bars: 3,7 ± 0,3
(7)Anti-roll bar link rod lower ball-joint
(8)Pivot lower ball-joint: 4 ± 0,4
(9) Driveshaft nut: 32,5 ± 2,5
(10)Wheel bolt: 9 ± 1
(11) Lower arm front mounting: 7,6 ± 0,7
(12)Lower arm rear mounting and anti-roll bar bearing: 6,8 ± 0,6
(13)Screw under rear mounting: 3,1 ± 0,3
(14) Ball-joint fixing on lower arm: 5 ± 0,5
Subframe to bodyshell fixing screw: 8,5 ± 0,8
B3CP040PB3CP041D
Vehicles from RPO 8667# are all
equipped as standard with ventilated
discs.
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 380

Downloaded from www.Manualslib.com manuals search engine 382
AXLES
SUSPENSION
STEERING
XSARA TIGHTENING TORQUES: REAR AXLE
Tightening torques (m.daN).
(1)Anti-roll bar lever: 3,2 ± 0,3
(2)Anti-roll bar
(3)Transversal torsion bars
(4)Rear crossmember flanges: 8,3 ± 0,8
(5)Front silentblocks: 5,5 ± 0,5
(6) Rear silentblocks: 4,5 ± 0,4
(7)Anti-vibration clamp
(8)Damper pin: 9,6 ± 0,9
(9)Stub axle nuts
(lubricated): 18,5 ± 1
NOTE:
- The RH torsion bar is identified by 1 paint line.
- The LH torsion bar is identified by 2 paint lines.
B3DP04SP
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 382

Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).(1) Damper nut: 4.5 ± 0.4
(2)Cup screw: 2.5 ± 0.2
(3)Suspension leg
(4)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(5)Suspension leg swivel: 4.5 ± 0.4
(6)Anti-roll bar
(7)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(8)Lower swivel ball-joint: 4 ± 0.4
(9)Hub nut
(greased): 32.5 ± 2
(10)Wheel bolt
(face and threads not greased): 9 ± 1
(11) Lower arm front pivot: 7.6 ± 0.7
(12) Lower arm rear pivot and
anti-roll bar bearing: 6.8 ± 0.6
(13) Screw under rear pivot : 3.5 ± 0.3
Lower arm in forged steel : 3.7 ± 0,3
Lower arm in plate steel: 3.1 ± 0,3
Screw fixing subframe on bodyshell: 8.5 ± 0,8
Screw fixing ball-joint on lower
arm
(plate steel): 4.5 ± 0,4
Anti-roll bar
Engines
ALL TYPESDiameter
21Colour ref.
WHITE Suspension leg angle:
Ta b«a»towards the front.
B3CP056P
B3CP057D
B3CP043D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 393

Downloaded from www.Manualslib.com manuals search engine 394
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: REAR AXLE
Tightening torques (m.daN).
(14)Front silentblock on subframe: 9.4 ± 0.9
(15)Anti-roll bar bolt: 5.5 ± 0.5
(16)Rear torsion bar
(17) Anti-roll bar
(18) Tubular axle
(19)Front silentblock on bodyshell: 4 ± 0.4
(20)Rear upper arm.
(21)Wheel bolt
(face and threads not lubricated): 9 ± 1
(22)Damper
(23)Rear silentblock on subframe: 5.4 ± 0.5
(24)Damper pin nut: 11 ± 1
(25)Stub axle nuts
(lubricated): 25 ± 2
(26)Rear silentblock on bodyshell: 6.5 ± 0.6
Anti-roll bar
Torsion bar
Engines
ALL TYPES 19,6 PINKØ (mm)
Colour ref.Ø (mm)
21Colour ref.
ORANGE
B3DP078D
NOTE: The RH torsion bar can be identified by 1 paint line.
The LH torsion bar can be identified by 2 paint lines.
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 394