ignition Citroen C4 2008 1.G User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C4, Model: Citroen C4 2008 1.GPages: 257, PDF Size: 8.06 MB
Page 39 of 257
40
II
M U L T I F U N C T I O N D I S P L A Y
Display ADisplay C or NaviDrive (continued)RangeThis indicates the mileage that can still be travelled using the f u e l r e m a i n i n g i n t h e t a n k .When the distance remaining to be travelled is less than abo ut 2 5 k m ( a p p r o x . 1 5 m i l e s ) , o n l y t h r e e d a s h e s a r e d i s p l a y e d .After resetting the computer, the indication of remaining range is only reliable after the vehicle has been used for a certain time.
Average fuel consumption
The average fuel consumption is calculated from the last reset of the computer.
Instantaneous fuel consumption
This is calculated from consumption over the previous 2 seconds. T h i s f u n c t i o n i s o n l y a v a i l a b l e w h e n t r a v e l l i n g a t o v e r 3 0 k m / h (approx. 20 mph).
Average speed
The average speed is obtained, from the last reset of the c o m p u t e r , b y d i v i d i n g t h e d i s t a n c e c o v e r e d b y t h e t i m e t a k e n (ignition on).
Distance travelled
It indicates the distance travelled since the trip computer was last reset to zero.
Distance remainingSee previous page.
Page 50 of 257
51
III
C O M F O R T
H e a t e d s e a t s
The front seats can be heated inde-pendently. Use the controls placed on the sides of the seats, turning them to select one of three heating levels:
0: Off.
1: Gentle heat.
2: Medium heat.
3: Strong heat.
The seat temperature will adjust ac-cordingly.
Note: The heated seats will only op-erate when the engine is running.
Note: The seats can still be moved on a temporary basis:
- when opening one of the front doors.
- after switching off the ignition.
E l e c t r i c a l l y o p e r a t e d a d j u s t m e n t s
A d j u s t m e n t o f s e a t h e i g h t , a n g l e a n d r e a c h
A d j u s t m e n t o f b a c k r e s t a n g l e a n d l u m b a r s u p p o r t
Raise or lower the front of control 1 to make the front of the seat cushion higher or lower.
Raise or lower the rear of control 1 to make the seat higher or lower.
Action control 1 to the front or to the rear to move the seat forward or back.
Push the top of control 2forward or back to adjust the backrest angle.
Raise or lower control 2to increase or decrease the lumbar support.
Page 51 of 257
52
III
C O M F O R T
M e m o r i s a t i o n o f d r i v i n g positions
You have the possibility to memorise two driving positions, via the buttons M / 1 and M / 2.
M e m o r i s a t i o n u s i n g t h e b u t t o n s
To memorise, using the buttons lo-cated on the side of the seat:
- turn the ignition key to the drive position,
- adjust your seat and your exterior rear view mirrors,
- press on button M then immediately on button 1 " fi r s t d r i v i n g p o s i t i o n " or on button 2 "second driving position".
The memorisation is recognised by an audible signal. Memorising of a new position cancels the previous one.
R e c a l l o f a m e m o r i s e d d r i v i n g position
V e h i c l e s t o p p e d (ignition on or en-gine running)
- P r e s s b r i e fl y o n b u t t o n 1 or2 to recall the corresponding memorised position.
Note: a f t e r fi v e c o n s e c u t i v e r e c a l l s of a memorised position, this function will be deactivated until the engine is started.
V e h i c l e m o v i n g
- Keep button 1 or 2 pressed to recall the corresponding memorised position.
Page 54 of 257
55
III
C O M F O R T
DOOR MIRRORS
A d j u s t m e n t o f r e a r v i e w m i r r o r s
Functions with ignition switched on.
From the driver’s position, select the rear view mirror via the control 1, then adjust in the four directions by moving the control 2.
Deicing of rear view mirrors is cou-pled with electric demisting of the rear screen.
F o l d - b a c k o f d o o r m i r r o r s
When the vehicle is parked, the door mirrors can be folded back either manually or electrically.
E l e c t r i c f o l d - b a c k
From the central position, one press towards the rear on control 1 folds the rear view mirrors back.
To return them to the initial position, press again on the control towards the rear.
A u t o m a t i c e l e c t r i c f o l d b a c k
Automatic fold-back operates when you lock the doors with the remote control.
The opposite movement applies when you unlock the doors, except if you operated fold-back before switching off the ignition.
Note: Automatic fold-back of the rear view mirrors can be deactivat-ed. Consult your CITROËN dealer.
A u t o m a t i c t i l t i n g o f m i r r o r s w h e n r e v e r s i n g
Ths function automatically gives you a view of the ground while reversing the vehicle.
Activation
With the engine running:
- Select the rear view mirror using control 1.
- Engage reverse gear, the mirror glass automatically positions itself to improve your vision of the pavement.
- If necessary, adjust the mirror to your preference using the electric control 2.
Deactivation
To deactivate the function, move control 1 to the central position.
Page 55 of 257
56
III
C O M F O R T
A u t o m a t i c p h o t o c h r o m i c i n t e r i o r r e a r v i e w m i r r o r
This provides an automatic and pro-gressive changing between day use and night use.
To avoid causing dazzle, the mirror au-tomatically becomes darker depend-ing on the intensity of light coming from the rear. It becomes lighter as soon as brightness diminishes, thus ensuring optimal vision.
To operate
Switch on the ignition and press control 1.
- Warning lamp 2 on: automatic mode.
- Warning lamp 2 off: automatic mode stopped. The mirror remains i n i t s l i g h t e s t d e fi n i t i o n .
Note: for optimal vision, the mirror lightens automatically when reverse gear is engaged.
M a n u a l i n t e r i o r m i r r o r
The lever on the lower edge enables you to place the rear view mirror in either of two positions:
Day position: the lever is not visible.
N i g h t p o s i t i o n ( a n t i d a z z l e ) : the lever is visible.
INTERIOR REAR VIEW MIRROR
Both the height and reach of the steering wheel can be adjusted.
W i t h t h e v e h i c l e a t r e s t , fi r s t a d j u s t the seat to the most suitable posi-tion, then adjust the position of the steering wheel.
STEERING COLUMN ADJUSTMENT
A d j u s t m e n t
Unlock the steering by pulling the control towards you.
Adjust the steering wheel position then lock by pushing the control fully downwards.
I f y o u p r e s s fi r m l y d o w n w a r d s o n your steering wheel after locking, you may hear a slight click. The steering i s t h e n i n i t s d e fi n i t i v e p o s i t i o n .
As a safety measure, do not adjust your driving position while driving.
Page 56 of 257
57
IV
A C C E S S
The key operates all the vehicle’s locks as well as the ignition.
Note: For safety reasons, a buzzer will sound if you have switched off the ignition and opened the driver’s door without previously removing the ignition key.
The key is used to deactivate the pas-senger’s front airbag (see "Safety").
It is dangerous to deadlock the vehicle when someone is inside as unlocking from the interior is impossible (without the remote control).
In the event of loss of the keys go to a CITROËN dealer with proof of ownership of the vehicle.
The CITROËN dealer network will be able to recover the key code and the transponder code to order replacement keys.
Central locking using the key
A brief action with the key locks the vehicle.
Central deadlocking using the key
A second action straight away with the key deadlocks the vehicle. It is then impossible to open the doors from either inside or outside the vehicle.
A long action with the key closes the windows.
Note: With the vehicle stationary and the engine switched off, locking i s s i g n a l l e d b y t h e fl a s h i n g o f t h e interior locking control warning lamp.
If any of the doors, or the boot, is open or not properly closed, central locking does not operate.
KEYS
Electronic immobiliser
The key contains a coded electronic chip. When switching on, the code must be recognised to allow the engine to be started.
This electronic immobiliser locks the engine management system a few seconds after switching off the ignition, and prevents unauthorised starting of the engine.
F o r a n y m o d i fi c a t i o n c o n c e r n i n g the keys it is essential to contact a CITROËN dealer taking the keys it is the keys it all of the keys in your possession with you.
Advice
If the key is not recognised, starting is not possible.
If this occurs, leave your vehicle immobilised and contact a CITROËN If this occurs, leave your vehicle vehicle
dealer.
Page 58 of 257
59
IV
A C C E S S
Guide-me-home lighting
A press on button C operates the guide-me-home lighting (illumination of the sidelamps and dipped beams for approx. one minute).
A second press prior to the end of this timing cancels the guide-me-home lighting.
Locating of the vehicle
To locate the vehicle in a carpark, press button A, the interior lamps come on and the direction indicators fl a s h f o r a f e w s e c o n d s . T h e v e h i c l e remains locked.
Folding and ejection of the key
Button D is for folding and ejecting the key from its housing in the remote control.
If you do not press on button D, you could damage the mechanism.
Except when reinitialising, the remote control cannot function while the key is in the ignition, even when switched off.
Warning: By inadvertently actioning the remote control, when for example it is in your pocket, you can unlock the vehicle without your realising it.
However, if no door is opened with 30 seconds of unloc king, the vehicle locks itself again automatically, without arming the alarm.
Warning: There a is a risk of damage if the replacement battery is not the correct one.
Only use batteries that are identical or equivalent to thos e approved by CITROËNOnly use batteries that are identical or equivalent to thoseOnly use batteries that are identical or equivalent to those.
Changing the remote control battery
Unclip the cover to gain access to the battery.
Battery: CR 0523: 3 V.
Re-initialisation of the remote control
After a change of battery, it is necessary to re-initialise the remote control. To do that, switch on the ignition and immediately action button A on your remote control to trigger the action desired. This may take some ten seco nds.
Do not throw away the old batteries. They should be retur ned to the CITROËN dealer or deposited in a recognised recycling facilityDo not throw away the old batteries. They should be retur ned Do not throw .
Take care not to place the remote control in contact with grease or dust, or leave it in the rain or in a damp environment.
A hard object also on the key ring, pressing on the key while it is in the ignition, can cause a malfunction.
Page 59 of 257
59
IV
A C C E S S
Guide-me-home lighting
A press on button C operates the guide-me-home lighting (illumination of the sidelamps and dipped beams for approx. one minute).
A second press prior to the end of this timing cancels the guide-me-home lighting.
Locating of the vehicle
To locate the vehicle in a carpark, press button A, the interior lamps come on and the direction indicators fl a s h f o r a f e w s e c o n d s . T h e v e h i c l e remains locked.
Folding and ejection of the key
Button D is for folding and ejecting the key from its housing in the remote control.
If you do not press on button D, you could damage the mechanism.
Except when reinitialising, the remote control cannot function while the key is in the ignition, even when switched off.
Warning: By inadvertently actioning the remote control, when for example it is in your pocket, you can unlock the vehicle without your realising it.
However, if no door is opened with 30 seconds of unloc king, the vehicle locks itself again automatically, without arming the alarm.
Warning: There a is a risk of damage if the replacement battery is not the correct one.
Only use batteries that are identical or equivalent to thos e approved by CITROËNOnly use batteries that are identical or equivalent to thoseOnly use batteries that are identical or equivalent to those.
Changing the remote control battery
Unclip the cover to gain access to the battery.
Battery: CR 0523: 3 V.
Re-initialisation of the remote control
After a change of battery, it is necessary to re-initialise the remote control. To do that, switch on the ignition and immediately action button A on your remote control to trigger the action desired. This may take some ten seco nds.
Do not throw away the old batteries. They should be retur ned to the CITROËN dealer or deposited in a recognised recycling facilityDo not throw away the old batteries. They should be retur ned Do not throw .
Take care not to place the remote control in contact with grease or dust, or leave it in the rain or in a damp environment.
A hard object also on the key ring, pressing on the key while it is in the ignition, can cause a malfunction.
Page 60 of 257
60
IV
A C C E S S
Arming the alarm using the remote control
Switch off the ignition and leave the vehicle.
Ensure that all doors and the boot are closed.
Lock the vehicle using button A on the remote control.
When the alarm is armed, the protections become active within 5 seconds (perimeter) and 45 seconds (volumetric).
Your vehicle may be equipped with an anti-intrusion alarm.
This ensures:
Page 61 of 257
61
IV
A C C E S S
Deactivation of volumetric detection
The alarm is able to operate with only perimeter protection if you deactivate the volumetric protection (if for example you wish to leave an animal in the vehicle).
To do this, switch off the ignition, then press immediately on control 1for at least one second.
The warning lamp 2 should be on p e r m a n e n t l y . I t w i l l s t a r t t o fl a s h when the alarm activates.
Arm the alarm by locking your vehicle using the remote control.
Disarming the alarm using the remote control
The alarm is disarmed when you unlock the vehicle (by pressing button B on the remote control).
Disarming the alarm using the key
Unlock the doors with the key. The siren is triggered. Enter the vehicle and switch on the ignition to stop the siren. Otherwise the siren will continue for about 30 seconds.
Note: