glove box Citroen C4 2010 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010, Model line: C4, Model: Citroen C4 2010 2.GPages: 284, PDF Size: 12.67 MB
Page 6 of 284
9
F A M I L I A R I S A T I O N
D A S H B O A R D
1. Bonnet release.
2. Fusebox cover.
3. Storage drawer (left and right).
4. Lateral air vent (left and right).
5. Side window demister vent
(left and right).
6. Loudspeaker (Tweeter)
(left and right).
7. Passenger’s airbag.
8. Control for central locking of doors
and boot.
9. Multifunction screen.
10. Hazard warning lamps control.
11. Scented air freshener.
12. Controls:
- Lighting.
- Direction indicators.
- Front foglamps
- Rear foglamps.
13. Steering column adjustment lever.
14. Radio-CD or NaviDrive radio
navigation.
15. Air conditioning or heating/
ventilation.
16. Cigar lighter.
17. 12-volt accessory socket
(120 W max). or USB port.
18. Ashtray.
19. Key-operated switch:
- Passenger’s airbag activation/ deactivation.
20. Lower glovebox.
- Handbook pack storage.
Page 22 of 284
25
I
M O N I T O R I N G
"Foot on brake" T h e fl a s h i n g o f t h i s w a r n i n g
lamp on the display informs
you that you need to press
the brake pedal in order to
be able to start the engine on a ve-
hicle with the (6-speed) Electronic
Gearbox System, or to move out of
position P in the case of an automatic
gearbox.
I t m a y a l s o fl a s h t o p r o m p t y o u t o
brake when engaging reverse gear.
In the case of the Electronic Gearbox
S y s t e m , t h i s w a r n i n g l a m p fl a s h e s t o
indicate overheating of the clutch if
you use the accelerator excessively
to hold the vehicle on an uphill slope.
Use the brake pedal instead.
Electric child lock
If lit, the child lock is activa ted.
This warning lamp is displayed
a few seconds after the func-
tion is activated. Deactivation warning lamps
If one of the following warning lamps
c o m e s o n , t h i s c o n fi r m s t h a t t h e
corresponding system has been
switched off intentionally.
Passenger's airbag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A s p e c i fi c b u t t o n , l o c a t e d o n t h e
dashboard, permits deactivation of
t h e s y s t e m . T h i s i s c o n fi r m e d b y
continuous lighting of this warning
lamp and of the indicator lamp on
the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lamps
Diesel engine pre-heating
Wait until this has gone out
before operating the starter.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lamps
indicates the occurrence of a fault
requiring action on the part of the
driver.
Any fault resulting in the displaying of
a warning lamp must be investigated
further by reading the associated mes-
sage on the multifunction screen.
Should you encounter any problems,
do not hesitate to contact a CITROËN
dealer.
The passenger's airbag sys-
tem is put into service auto-
matically when the vehicle is
started.
A control switch, located in the glove
box, permits deactivation of the sys-
t e m . T h i s i s c o n fi r m e d b y c o n t i n u o u s
lighting of this warning lamp on the
instrument panel or a message on
the NaviDrive multifunction screen.
Page 26 of 284
25
I
M O N I T O R I N G
"Foot on brake" T h e fl a s h i n g o f t h i s w a r n i n g
lamp on the display informs
you that you need to press
the brake pedal in order to
be able to start the engine on a ve-
hicle with the (6-speed) Electronic
Gearbox System, or to move out of
position P in the case of an automatic
gearbox.
I t m a y a l s o fl a s h t o p r o m p t y o u t o
brake when engaging reverse gear.
In the case of the Electronic Gearbox
S y s t e m , t h i s w a r n i n g l a m p fl a s h e s t o
indicate overheating of the clutch if
you use the accelerator excessively
to hold the vehicle on an uphill slope.
Use the brake pedal instead.
Electric child lock
If lit, the child lock is activa ted.
This warning lamp is displayed
a few seconds after the func-
tion is activated. Deactivation warning lamps
If one of the following warning lamps
c o m e s o n , t h i s c o n fi r m s t h a t t h e
corresponding system has been
switched off intentionally.
Passenger's airbag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A s p e c i fi c b u t t o n , l o c a t e d o n t h e
dashboard, permits deactivation of
t h e s y s t e m . T h i s i s c o n fi r m e d b y
continuous lighting of this warning
lamp and of the indicator lamp on
the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lamps
Diesel engine pre-heating
Wait until this has gone out
before operating the starter.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lamps
indicates the occurrence of a fault
requiring action on the part of the
driver.
Any fault resulting in the displaying of
a warning lamp must be investigated
further by reading the associated mes-
sage on the multifunction screen.
Should you encounter any problems,
do not hesitate to contact a CITROËN
dealer.
The passenger's airbag sys-
tem is put into service auto-
matically when the vehicle is
started.
A control switch, located in the glove
box, permits deactivation of the sys-
t e m . T h i s i s c o n fi r m e d b y c o n t i n u o u s
lighting of this warning lamp on the
instrument panel or a message on
the NaviDrive multifunction screen.
Page 27 of 284
25
I
M O N I T O R I N G
"Foot on brake" T h e fl a s h i n g o f t h i s w a r n i n g
lamp on the display informs
you that you need to press
the brake pedal in order to
be able to start the engine on a ve-
hicle with the (6-speed) Electronic
Gearbox System, or to move out of
position P in the case of an automatic
gearbox.
I t m a y a l s o fl a s h t o p r o m p t y o u t o
brake when engaging reverse gear.
In the case of the Electronic Gearbox
S y s t e m , t h i s w a r n i n g l a m p fl a s h e s t o
indicate overheating of the clutch if
you use the accelerator excessively
to hold the vehicle on an uphill slope.
Use the brake pedal instead.
Electric child lock
If lit, the child lock is activa ted.
This warning lamp is displayed
a few seconds after the func-
tion is activated. Deactivation warning lamps
If one of the following warning lamps
c o m e s o n , t h i s c o n fi r m s t h a t t h e
corresponding system has been
switched off intentionally.
Passenger's airbag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A s p e c i fi c b u t t o n , l o c a t e d o n t h e
dashboard, permits deactivation of
t h e s y s t e m . T h i s i s c o n fi r m e d b y
continuous lighting of this warning
lamp and of the indicator lamp on
the button.
From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lamps
Diesel engine pre-heating
Wait until this has gone out
before operating the starter.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lamps
indicates the occurrence of a fault
requiring action on the part of the
driver.
Any fault resulting in the displaying of
a warning lamp must be investigated
further by reading the associated mes-
sage on the multifunction screen.
Should you encounter any problems,
do not hesitate to contact a CITROËN
dealer.
The passenger's airbag sys-
tem is put into service auto-
matically when the vehicle is
started.
A control switch, located in the glove
box, permits deactivation of the sys-
t e m . T h i s i s c o n fi r m e d b y c o n t i n u o u s
lighting of this warning lamp on the
instrument panel or a message on
the NaviDrive multifunction screen.
Page 92 of 284
80
VI
F I T T I N G S
ILLUMINATED GLOVE BOX
I t s l i d h a s a r e a s f o r s t o r i n g a p e n , a
p a i r o f s p e c t a c l e s , t o k e n s , c a r d s , a
c u p , f r a g r a n c e c a r t r i d g e s . . .
T o o p e n t h e g l o v e b o x , r a i s e t h e
handle and lower the lid.
COOLED GLOVE BOX
I t m a y b e c o o l e d , d e p e n d i n g o n y o u r
v e h i c l e ’ s e q u i p m e n t , b y a v e n t i l a t i o n
duct that can be closed off manually.
W i t h a i r c o n d i t i o n i n g , t h i s d u c t d i s -
tributes the same cooled air as the
vents in the passenger compart-
ment.
T h e c o o l i n g o f y o u r g l o v e b o x o n l y
operates when the engine is running
and the air conditioning is on.
The lamp comes on au-
tomatically when the lid is
opened. F o r s a f e t y r e a s o n s , t h e
g l o v e b o x s h o u l d r e m a i n
closed when the vehicle is
moving.
Page 98 of 284
80
VI
F I T T I N G S
ILLUMINATED GLOVE BOX
I t s l i d h a s a r e a s f o r s t o r i n g a p e n , a
p a i r o f s p e c t a c l e s , t o k e n s , c a r d s , a
c u p , f r a g r a n c e c a r t r i d g e s . . .
T o o p e n t h e g l o v e b o x , r a i s e t h e
handle and lower the lid.
COOLED GLOVE BOX
I t m a y b e c o o l e d , d e p e n d i n g o n y o u r
v e h i c l e ’ s e q u i p m e n t , b y a v e n t i l a t i o n
duct that can be closed off manually.
W i t h a i r c o n d i t i o n i n g , t h i s d u c t d i s -
tributes the same cooled air as the
vents in the passenger compart-
ment.
T h e c o o l i n g o f y o u r g l o v e b o x o n l y
operates when the engine is running
and the air conditioning is on.
The lamp comes on au-
tomatically when the lid is
opened. F o r s a f e t y r e a s o n s , t h e
g l o v e b o x s h o u l d r e m a i n
closed when the vehicle is
moving.
Page 156 of 284
133
XI
P R A C T I C A L I N F O R M A T I O N
CHANGING A WHEEL
Access to the tools
The tools are located in the spare
w h e e l , u n d e r t h e b o o t fl o o r .
To gain access to them:
open the boot,
l i f t t h e fl o o r ,
unclip and remove the box con-
t a i n i n g t h e t o o l s . List of tools
A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
v e h i c l e . D o n o t u s e t h e m f o r o t h e r
p u r p o s e s .
1. Wheelbrace *
2. Jack with handle *
3. Aluminium wheel central embel-
lisher removal tool *
4. S o c k e t f o r s e c u r i t y b o l t s ( l o c a t e d
in the glove box)
Fits the wheelbrace
5. R e m o v a b l e t o w i n g e y e Access to the spare wheel
The spare wheel is installed in the
b o o t , u n d e r t h e fl o o r .
Removing the wheel
U n d o t h e y e l l o w c e n t r a l s c r e w b y
a q u a r t e r t u r n .
Raise the spare wheel towards
y o u r e a r w a r d s .
Remove the wheel from the boot
s p a c e .
* O n l y w h e r e t h e v e h i c l e h a s a s p a r e
w h e e l .
Page 157 of 284
133
XI
P R A C T I C A L I N F O R M A T I O N
CHANGING A WHEEL
Access to the tools
The tools are located in the spare
w h e e l , u n d e r t h e b o o t fl o o r .
To gain access to them:
open the boot,
l i f t t h e fl o o r ,
unclip and remove the box con-
t a i n i n g t h e t o o l s . List of tools
A l l o f t h e s e t o o l s a r e s p e c i fi c t o y o u r
v e h i c l e . D o n o t u s e t h e m f o r o t h e r
p u r p o s e s .
1. Wheelbrace *
2. Jack with handle *
3. Aluminium wheel central embel-
lisher removal tool *
4. S o c k e t f o r s e c u r i t y b o l t s ( l o c a t e d
in the glove box)
Fits the wheelbrace
5. R e m o v a b l e t o w i n g e y e Access to the spare wheel
The spare wheel is installed in the
b o o t , u n d e r t h e fl o o r .
Removing the wheel
U n d o t h e y e l l o w c e n t r a l s c r e w b y
a q u a r t e r t u r n .
Raise the spare wheel towards
y o u r e a r w a r d s .
Remove the wheel from the boot
s p a c e .
* O n l y w h e r e t h e v e h i c l e h a s a s p a r e
w h e e l .
Page 170 of 284
146
XI
P R A C T I C A L I N F O R M A T I O N
Interior lighting
Interior lamp (1/W5W)
D e t a c h t h e c o v e r o f t h e i n t e r i o r
lamp 1 with a thin screwdriver, close
t o t h e b u t t o n , t o a c c e s s t h e f a u l t y
b u l b .
Map reading lamps (2/W5W)
D e t a c h t h e c o v e r o f t h e i n t e r i o r l a m p .
T o a c c e s s t h e f a u l t y b u l b , d e t a c h t h e
partition for the reading lamp 2 con-
c e r n e d , a s n e c e s s a r y . Boot lamp (W5W)
D e t a c h t h e u n i t b y p u s h i n g i t r e a r -
w a r d s .
Sill lamps (W5W)
D e t a c h t h e l a m p t o a c c e s s t h e b u l b . Glove box lamp (W5W)
D e t a c h t h e l a m p t o a c c e s s t h e b u l b .
Page 223 of 284
199
11
2 2
11
3 3
2 2
Press the MENU button then select the CONFIGURATION function, then SOUNDS, then ACTIVATE AUXILIARY SOURCE to acti vate the auxiliary input of the NaviDrive.
Connect the portable equipment (MP3 player…) to the audio sockets (white and red, RCA type) located in the glove box using a JACK/RCA audio cable.
Press the SOURCE button several times in succession and select AUX.
The display and management of the commands is done via the portable equipment.
I t i s n o t p o s s i b l e t o c o p y t h e fi l e s o n t o t h e h a r d d i s k f r o m t h e a u x i l i a r y input.
USING THE AUXILIARY INPUT (AUX)
JACK/RCA AUDIO CABLE NOT SUPPLIED
AUDIO/VIDEO
CD CHANGER
Insert the CDs in a multi-slot changer (not MP3 compatible) one by one. On a single slot changer (MP3 compatible), press LOAD, select the number of the CD, then insert the CD, or press and hold LOAD and insert the CDs one by one. Press the SOURCE button several times in succession and select CD CHANGER.
Press one of the buttons on the alphanumeric keypad to select the corresponding CD.
Press one of the buttons to select a track on the CD.
I t i s n o t p o s s i b l e t o c o p y t h e fi l e s o n t o t h e h a r d d i s k f r o m t h e C D changer.
CD CHANGER
PLAYING A CD