change time Citroen C4 AIRCROSS RHD 2012 1.G Owner's Manual

22
Familiarisation















































Eco-driving
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2emissions.
Optimise the use of your
gearbox
With a manual gearbox, move off gently,change up without waiting and drive by changing up quite soon. If your vehicle has the system, the gear efficiency indicator invites you to change up; it is displayed in the instrument panel, follow its instructions.
With an automatic or electronic gearbox, stay in Drive "D"or Auto "A"
, according to the type of gearbox, without pressing theaccelerator pedal heavily or suddenly.
Drive smoothly
Maintain a safe distance between vehicles, use engine braking rather than the brake pedal,and press the accelerator progressively. These practices contribute towards a reduction in fuelconsumption and CO2 emissions and also helpsreduce the background traffic noise.
If your vehicle has cruise control, make use of the system at speeds above 25 mph (40 km/h) when the traffic is flowing well.


Control the use of your
electrical equipment


Before moving off, if the passenger compartment is too warm, ventilate it byopening the windows and air vents before using
the air conditioning.
Above 30 mph (50 km/h), close the windows and leave the air vents open.
Remember to make use of equipment that canhelp keep the temperature in the passenger compartment down (sunroof and windowblinds...).
Switch off the air conditioning, unless it has automatic digital regulation, as soon as thedesired temperature is attained. Switch off the demisting and defrostingcontrols, if not automatic. Switch off the heated seat as soon as possible.

Switch off the headlamps and front foglampswhen the level of light does not require their use.

Avoid running the engine before moving off,particularly in winter; your vehicle will warmup much faster while driving.

As a passenger, if you avoid connecting your multimedia devices (film, music, videogame...), you will contribute towards limitingthe consumption of electrical energy, and soof fuel.
Disconnect your por table devices beforeleaving the vehicle.

1
45
Monitoring

Resetting the service indicator to zero


After a certain distance and a certain time, the display of "---"
is reset automatically and the display indicatesthe time remaining before the nextservice is due.
Yo u r C I T R O
ËN dealer or a qualified workshopcarries out this operation after each ser vice.
If you have carried out your vehicle's ser vice yourself, the zero reset procedure is the
following:)switch off the ignition,)press the INFO
button several times in succession until the service indicator is displayed,)press and hold the INFO
button for a few seconds until the spanner flashes,)press the INFO
button while the spanner
is flashing to change the display "---" to"CLEAR"then the time remaining before
the next ser vice is due is displayed.

48
Monitoring
The various menus may change between the type 1instrument panel and the type 2 instrument panel.
Adjusting vehicle settings
When the vehicle is stationary, it allows theyuser to change the following settings:


- the reset mode
for average fuelconsumption and average speed,
)Press and hold the INFObutton for a fewseconds to display the menu screen.
)In the menu screen, press the INFO
button
to select a function from the list:
- the
fuel consumption units,
- the temperature displa
y unit,
- the display language,
- activation/deactivation of the sound whenpressing the INFO
button,- the rest reminder display interval,
- restore the factory settings.
To change the settings, you must stopthe vehicle and switch on the ignition.
Apply the parking brake and place the gear lever in neutral. With the ignition on
, press the INFObutton
on the dashboard, to the right of the instrumentpanel, several times in succession until the
"SETTINGS MENU" screen is displayed.


Operation
MENU1/3:-1 - 2, A - M, A - P*
(choice of the type of reset of average fuel consumption andaverage speed),

- AVG UNIT(choice of the fuel consumption
units),

- choice of the temperature display unit,-LANGUAGE(option of the display
language),

*
According to display language.
For your safety,when the vehicle ismoving
, the function settings are not displayed when you press the INFObutton.

58
Monitoring
The digital clock is set automatically.yThis mode enables the system to set the local
time automatically using the signal from theRDS stations. )On the control panel, press button A(SET)
to access the "Settings"
menu.
)
On the touch screen, press button B
toaccess the "System"menu.
The system settings screen is displayed.

You must deactivate automaticadjustment (RDS Auto Correct) to change the time zone and summer time settings. On each screen, you can return to theprevious screen by pressing button D"Back".
)
Press button C
to access the "Time"
menu.
1.RDS Auto Correct: Activate / deactivate automatic adjustment. 2.GMT / GMT+1 / GMT+2: Select the time zone. 3.Summer Time: Summer time On / Off.)Press button Dto confirm and return to theprevious menu.
Once this menu has been selected, you can
access the following functions:

1
59
Monitoring





Lighting dimmer

System for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.
There is an audible signal and the intensity of the lighting increases eachtime the button is pressed.
With the li
ghting on or off, press the button
to change the intensity of the lighting of the instruments and controls in "day" or "night"mode.
When the lighting reaches the maximum
setting, press again to change to the minimum
settin
g.
When the lighting reaches the required intensity, release the button.

With the vehicle's li
ghting off, only the
brightness of the instrument panel is modified.
The setting is saved when the ignition switch is
turned to OFF.

Wit the vehicle's li
ghting on, the brightness of
the entire dashboard (instrument panel, screen,
air conditioning control panel...) is modified.

75
2
Access

Tr iggering of the alarm


This is indicated by sounding of the siren andflashing of the direction indicators for thirtyseconds.
A message then appears in the instrument
panel screen while the siren is operating.
When the ignition is next switched on (ONmode if your vehicle has the "Keyless Entry and Starting" system), an audible signal sounds four
times to inform you that the alarm was triggeredduring your absence.
Complete deactivation of
the alarm
)
Switch off the ignition (OFF mode if your vehicle has the "Keyless Entry andStarting" system). )
Remove the key from the ignition switch,
if your vehicle does not have the "Keyless
Entry and Star ting" system.) Open the driver's door. )
Place the lighting control stalk in the "OFF"position. )
Pull the wiper control stalk towards you and
hold.
After about ten seconds there is an audible signal.) When the audible signal stops, continue to
hold the wiper stalk pulled towards you and
press the remote control locking button.
You can completely deactivate the alarm
system. To do this, proceed as follows:
) The state of the system is then signalled to you by the number of beeps:
One beep: the alarm system is completely deactivated.
Two beeps: the alarm system is activated.
Each new press of the remote control
lockin
g button changes the state of thesystem.
It is possible to adjust the sensitivity
of the alarm sensor and to deactivatethe function via the colour screen"Equipment" menu.

94
Comfort

Personalisation of theExterior air intake / Interior air recirculation function

This function is controlled automatically.However, you can deactivate its automatic control if you wish to change the air intake
mode at any time.

Changing the status

Press the Air intake / Interior air recirculation button for at least 10 seconds.
When the status chan
ges from active to
inactive, three bleeps are heard and the
indicator lamp
flashes three times.
When the status changes from inactive to
active, two bleeps are heard and the indicator lamp flashes three times.
Automatic control active

If the air distribution adjustment dial and the air flow adjustment dial are placed in the "AUTO" position, the Air intake / Interior air recirculation
function is also controlled automatically.

Automatic control inactive

Even if the air distribution adjustment dial and
the air flow adjustment dial are placed in the
"AUT
O" position, the Air intake / Interior air
recirculation function is no longer controlled
automatically.
The settings are retained, even after switching
off the ignition.
4. Intake of exterior air /
Recirculation of interior air
This function insulates the passenger compartment from exterior odours and smoke.
) Press button 4to select the air intake mode.
When the indicator lamp on button 4
is off, the exterior air intake function is on.
When the indicator lamp on button 4 is on, the
intake of exterior air is off and the system is in air recirculation mode.
Do not drive for long periods in interior air recirculation mode, except in truly exceptional atmospheric conditions.

95
3
Comfort

5. Air conditioning On / Off
)
Press button 5
to activate the air conditioning.
The indicator lamp comes on.Personalisation of the Air
Conditioning On / Off function
This function is controlled automatically. However, you can deactivate its automatic control if you wish to activate or deactivate theair conditioning at any time.
Changing the status
Press the Air Conditioning On / Off button for atleast 10 seconds.
When the status chan
ges from active to inactive, three bleeps are heard and theindicator lamp flashes three times.
When the status changes from inactive to active, two bleeps are heard and the indicator lamp flashes three times.
Automatic control active

If the air distribution adjustment dial and the
air flow adjustment dial are placed in the
"AUTO" position, or if the temperature control
dial is set to the minimum temperature, the air
conditioning system is controlled automatically.


Automatic control inactive

The air conditioning system is no longer controlled automatically.

113
4
Driving
This gearbox has two driving modes:


- an automated mode for automatic control
of the gears by the gearbox and therefore
without any action on the par t of the driver,

- a manual mode for sequential changing of
the gears by the driver using the steeringmounted controls or the gear lever.





CVT gearbox
It includes the following controls:
- a gear lever 1
on the centre console for selecting the driving mode, reverse gear
and neutral or for changing gear in manual
mode,
-
a "-"
steering mounted control paddle 2
for manual downward gear changes,

- a "+/OFF"steering mounted control paddle 3for manual upward gear changes.

The six-speed automatic
gearbox offers a choice between the comfor t of automatic regulation or the pleasure of manual gear changing.


The mode can be changed at any time.

116
Driving
Manual gear changing
In the automated mode, you can take over
control temporarily at any time using thesteering mounted controls.
The use of these controls permits manualselection of the gears in situations whichrequire a faster change down than that offered
in automated mode (arrival at a roundabout, exit from a car park with a steep gradient,
over taking...).
The gearbox engages the gear requested if
the engine speed permits it. The gear engaged appears.
To return to the automated mode, do one of thefollowing:
- press the back of the "+/OFF"steering mounted control 3for approximately2 seconds,
- move the gear lever quickly towardsposition +/-
and then return it to position D ,
- stop the vehicle.


Stopping the vehicle
Operating fault

With the ignition on, if the message "Slow
down"
or "Service required"
appears in
the instrument panel screen, this indicates a
gearbox malfunction.
When a message is displayed, carry out thefollowing operations:


- slow down and stop your vehicle in a safe place,

- place the lever in position P
and let the engine run,

- open the bonnet to allow the engine to cool.
If the message disappears for a long period, you can set off again.
If the message remains displayed or appears
frequently, contact a CITROËN dealer or aqualified workshop without delay. Before switchin
g off the engine, you must place
the gear lever in position P.P You must apply the parking brake to immobilise
the vehicle.