power steering Citroen C4 AIRCROSS RHD 2014 1.G Owner's Manual

1
35
Monitoring


Screen 1



Screen 2



Cause



Solution - Action



Observations




Warning messages (ignition at "ON")

Fault with the electric power
steering. Stop the vehicle, wait few moments
then start the engine again. If the message remains after
restarting, contact a CITROËN
dealer or a qualified workshop.
The battery for the "Keyless Entry
and Starting" system is flat. Replace the battery (see "Changing
the batteries").
The electronic key that you have on
your person is not recognised. Check that you have the correct
electronic key. If the message persists, contact a
CITROËN dealer.
The electronic key is still in the
vehicle and you have tried to lock
the doors or boot from the outside. Ensure that you have the electronic
key on your person before locking
the vehicle.
One of the doors or the boot is not
properly closed when locking the
vehicle from the outside. Close the door or the boot, then
lock the vehicle.
Fault with the "Keyless Entry and
Starting" system. Contact a CITROËN dealer.

108
Driving








Starting - stopping the engine with the key



- Position 1: LOCK

The steering is locked.

- Position 2: ACC

The accessories (radio, 12 V socket...) can
be used.

- Position 3: ON

Ignition on.

- Position 4: START

Starting the engine.


Ignition switch


If you use the accessories for a
prolonged period (with the key in
position 2 (ACC)
), you risk discharging
the battery. Starting your vehicle will
then no longer be possible. Be aware
.
See the "Automatic power cut-off to
accessories" section.








Key in ignition

A buzzer sounds on opening the
driver's door, if the key has been left in
the ignition.

)
Insert the key in the ignition switch.

)
Turn the key to position 2 (ACC)
and unlock
the steering column, by turning wheel
slightly.

)
Press and hold the brake pedal.

)
Fully depress the clutch pedal (vehicles
fitted with a manual gearbox).

)
Put the gear lever into neutral (vehicles
fitted with a manual gearbox), or in
position P
(vehicles fitted with a CVT
gearbox).

)
Operate the starter by turning the key to
position 4 (START)
.

)
Once the engine is running, release
the key.
The key returns automatically to
position 3 (ON)
.


Starting using the key
Stopping



)
Immobilise the vehicle.

)
Put the gear lever into neutral (vehicles
fitted with a manual gearbox), or in
position P
(vehicles fitted with a CVT
gearbox).

)
While pressing the key, turn it to
position 1 (LOCK)
.

)
Remove the key from the ignition switch.

)
Lock the steering.

Do not attach any heavy objects to the
key as this could weigh down on it when
in the ignition switch and cause a fault.


For Diesel vehicles, when the engine
is cold wait with the ignition switch
in position 3 (ON)
until the preheater
warning lamp goes off, before turning
the key to position 4 (START)
.
The warning lamp does not come on
when the engine is hot.

Switching off the engine leads to a loss
of braking assistance.

111
4
Driving

Once the engine has started, you can
remove the electronic key from its
housing A
and close the glove box.


Back-up starting with the
electronic key

The message is displayed
when you open the driver's
door and the electronic key
has not been removed from
its location A
. Remember to take the electronic
key with you when you leave the vehicle.

)
Press the brake pedal on vehicles fitted
with a CVT gearbox or depress the clutch
pedal fully on vehicles with a manual
gearbox.

)
Press the " START/STOP
" button.


When the electronic key is in the defined zone
and your vehicle does not start after pressing
the " START/STOP
" button:


)
Open the glove box.

)
Insert the electronic key in the location A
.


Emergency stop with the
electronic key

During an emergency stop, the braking
servo assistance and steering power
assistance functions are no longer
provided. Take great care.

In the event of an emergency only
, the
engine can be stopped without any conditions.
To do this, press and hold the " START/
STOP
" button for about 3 seconds or make
3 successive presses on the button.
The engine stops and the vehicle goes into
"ACC" mode.

121
4
Driving








Stop & Start (Auto Stop & Go) function


Operation


Going into engine STOP mode

The "AS &G"
warning lamp comes on in
the instrument panel or the instrument
panel screen and the engine goes into
standby after a few seconds:


- with a manual gearbox
, with the vehicle
stationary and your foot on the brake, when
you put the gear lever into neutral and
release the clutch pedal.


Never refuel with the engine in STOP
mode; you must switch off the ignition
with the key or the START/STOP
button.
When the engine is stopped
automatically, the operation of certain
vehicle systems, such as for example,
braking, power steering... are modified.
Ta k e c a r e
.


Special cases: STOP mode not
available
STOP mode is not invoked when:


- the driver's seat belt is not fastened,

- the bonnet is open,

- the vehicle has not exceeded 3 mph
(5 km/h) since the last engine start,

- the vehicle has restarted less than
10 seconds ago,

- the engine is needed to maintain a
comfortable temperature in the passenger
compartment,

- demisting is active,

- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.

- the "AS &G"
warning lamp is
flashing in the instrument panel.

This operation is per fectly normal.


The Stop & Start (Auto Stop & Go) function puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, or other...).
The engine restarts automatically as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Start (Auto Stop & Go) function reduces fuel consumption and exhaust emissions as well as the noise level when
stationary.

204
Practical information





Recovering the vehicle



Recover y of your vehicle


2 wheel drive (2WD) versions: towing
with the wheels on the ground



)
Put the gear lever into neutral (position N

for the CVT gearbox).

)
Unlock the steering by by turning the
ignition switch to the " ON
" position (or
to " ON
" mode for vehicle fitted with the
"Keyless Entry and Starting" system).

)
Release the parking brake.

)
Switch on the hazard warning lamps on
both vehicles.

)
Move off gently and travel slowly for a short
distance only.



General recommendations

Observe the legislation in force in your
country.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a vehicle with all four
wheels on the ground, always use an
approved towing bar; rope and straps
are prohibited.
When towing a vehicle with the engine
off, there is no longer any power
assistance for braking or steering.
In the following cases, you must always
call on a professional recovery ser vice:


- vehicle broken down on a motor way
or fast road,

- 4 wheel drive vehicle,

- when it is not possible to put the
gearbox into neutral, unlock the
steering, or release the parking
brake,

- towing with only two wheels on the
ground,

- where there is no approved towing
bar available...

Towing with the wheels on the ground
is only possible on 2 wheel drive (2WD)
versions.

)
Fit the towing bar to the towing eye on the
chassis, located under the front bumper.