clock CITROEN C4 CACTUS 2022 Owners Manual

151
Important: in the event of a top-up after
a breakdown because of a lack of
AdBlue, you must wait around 5 minutes
before switching on the ignition, without
opening the driver's door, locking
the vehicle, introducing the key into
the ignition switch, or introducing
the key of the

K
eyless Entr y and
Star ting system into the passenger
compartment .
Switch on the ignition, then wait for 10
seconds before starting the engine.
Access to the AdBlue® tank
via the boot
Filling the AdBlue® tank is an operation
included in every routine ser vice on your
vehicle by a CITROËN dealer or a qualified
workshop.
Nevertheless, given the capacity of the tank, it
may be necessary to top up the fluid between
ser vices, as soon as an alert (warning lamps
and a message) indicates it.
You are recommended to go to a CITROËN
dealer or a qualified workshop.
If you intend to do the topping-up yourself,
read the following procedure carefully.
The supply in a non-drip bottle simplifies the
topping-up. F

S
witch off the ignition and remove the key.
Or
F
W
ith
K
eyless Entry and Starting, press the
" START/STOP " button to switch off the
engine.
F
F
rom the boot, lift the carpet and then,
depending on the equipment, lift out the
spare wheel and/or the storage box.
F

W
ithout pressing, turn the black cap a
quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap anti-clockwise.
Access to the AdBlue® tank
via the fuel filler flap
A blue cap under the fuel filler flap indicates
access to the AdBlue® tank.
Read the following procedure carefully to
be able to top up properly.
F

S

witch off the ignition and remove the key.
Or
F

W

ith

K

eyless Entry and Starting, press the
" START/STOP " button to switch off the
engine.
F

T

ake non-drip bottles of AdBlue
®. After first
checking the use-by date, read carefully
the instructions on use on the label before
pouring the contents of the bottle into your
vehicle's AdBlue
® tank.
F
A
fter filling, per form the same operations in
reverse order.
7
Practical information

152
F Obtain a container of AdBlue®. After first
checking the use-by date, read carefully
the instructions on use on the label before
pouring the contents of the container into
your vehicle's AdBlue
® tank.
Or
F

I

nsert the AdBlue
® pump nozzle and fill the
tank until the nozzle stops automatically.
Important:
To prevent the AdBlue
® tank from
ov
er flowing, it is recommended:
F

T

o top up between 10 and 13 litres
using AdBlue
® containers.
Or
F

I

f filling in a ser vice station, stop after
the third automatic shut-off of the
nozzle.
F

A

fter refilling, carry out these same
operations in reverse order.
F

W

ith the vehicle unlocked and the fuel filler
flap open, turn the AdBlue
® blue filler cap
anti-clockwise.Advice on care and
maintenance
Recommendations on the care and
maintenance of your vehicle are given in the
Maintenance and Warranty Guide.
Leather
Leather is a natural product. Appropriate
regular care and cleaning is essential for its
durability.
Refer to your vehicle's Maintenance and
Warranty Guide for information on all the
special precautions to observe.
Care of the stickers
These styling stickers are treated to give good
resistance to ageing and tearing.
They have been designed to allow you to
customise your vehicle's bodywork.
When using a high pressure jet wash, keep the
end of the lance at least 30 centimetres from
the stickers. For the care of the stickers in the rear door
windows, we recommend the following:
-

U
se a wide jet at a temperature of
between 25°C and 40°C.
-
W
here possible, direct the jet at right
angles to the stickers.
Practical information

163
To refit, carry out these operations in reverse
o r d e r.
Direction indicators
Quicker flashing of the direction indicator
lamp (left or right) indicates the failure of
one of the bulbs on the corresponding
side.
F

T
urn the bulb holder an eighth of a turn anti-
clockwise and extract it.
F

R
emove the bulb and replace it.
To refit, carry out these operations in reverse
o r d e r. Amber colour bulbs, such as the direction
indicators, must be replaced by bulbs with
identical colour and specifications.
Foglamps
F Below the front bumper, unscrew the three
wheel arch liner fixing screws.
F

M
ove the wheel arch aside to allow access
to the front foglamp.
F

D
isconnect the connector from the bulb
holder by pressing on its tab, located at the
top. To refit, carry out these operations in reverse
o r d e r.
F

P

ush on the spring, then move it towards
the middle of the vehicle to release the bulb.
F

P

ull the bulb out and change it.
You can also contact a CITROËN
dealer or a qualified workshop for the
replacement of these bulbs.
Integrated direction indicator
side repeaters
For the replacement of these bulbs, contact a
CITROËN dealer or a qualified workshop. F
R
emove the bulb holder by squeezing the
two clips (top and bottom) with the thumb
and forefinger.
F
R
eplace the module (bulb holder and bulb).
8
In the event of a breakdown

165
To refit, carry out these operations in reverse
o r d e r.
Make sure the reversing lamp is connected
properly before refitting the bulb holder.
Take care to engage the lamp in its guides
while remaining within the vehicle's centreline.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
Sidelamps (LED) and foglamps
(LED)
For the replacement of LEDs, contact a
CITROËN dealer or a qualified workshop.
Third brake lamp (LED)
For the replacement of LEDs, contact a
CITROËN dealer or a qualified workshop.
Number plate lamps (W5W)
Interior lighting
Courtesy lamp with bulbs (W5W)
F Using a thin, flap tip screwdriver, unclip the entire console surrounding the courtesy
lamp.
F

P
ull the faulty bulb out and change it.
F

P
ut in place the console around the
courtesy lamp and clip it correctly.
Courtesy lamp with LED
For the replacement of LEDs, contact a
CITROËN dealer or a qualified workshop.
-

f

or the other lamps, press gently from the
top and turn the corresponding bulb a
quarter turn anti-clockwise.
F

I

nsert a thin screwdriver into one of the cut-
outs in the lens. F

P
ush it outwards to unclip it.
F
R
emove the lens.
F
C
hange the faulty bulb.
To refit, press on the lens to clip it in place.
8
In the event of a breakdown