lock Citroen C4 DAG 2014.5 2.G Owner's Guide

71 
C4-2_en_Chap04_ouvertures_ed01-2014
Lost keys
Go to a  CITROËN  dealer  with  the  vehicle's  registration  document,  your  personal
  identification   documents   and   if   possible   the   key   code   label.
The
 
CITROËN
 
dealer
 
will
 
be
 
able
 
to
 
look
 
up
 
the
 
key
 
code
 
and
 
the
 
transpon
-
der
  code   required   to   order   a   new   key. Do
 
not
 
throw
 
the
 
remote
 
con
-
trol batteries away, they contain
metals  which  are  harmful  to  the  environment.
T
ake  
them
 
to
 
an
 
approved
 
col
-
lection
  point.
Remote control
The high frequency  remote  control  is  a  sensitive  system;  do  not  operate  it  while
 it  is  in  your  pocket  as  there  is  a  possibility  that  it  may  unlock  the  ve -
hicle,
  without   you   being   aware   of   it.
Do
 
not
 
repeatedly
 
press
 
the
 
buttons
 
of
 
your
 
remote
 
control
 
out
 
of
 
range
 
and
 
out

 
of
 
sight
 
of
 
your
 
vehicle.
 
Y
ou  
run
 
the
 
risk
 
of
 
stopping
 
it
 
from
 
working
 
and
 
the

  remote   control   would   have   to   be   reinitialised.
No
 
remote
 
control
 
can
 
operate
 
when
 
the
 
key
 
is
 
in
 
the
 
ignition
 
switch,
 
even
 
when

  the   ignition   is   switched   off,   except   for   reinitialisation.
Locking the vehicle
Driving with the  doors  locked  may  make  access  to  the  passenger  compart -
ment   by   the   emergency   services   more   difficult   in   an   emergency.
As
 
a
 
safety
 
precaution,
 
never
 
leave
 
children
 
alone
 
in
 
the
 
vehicle,
 
except
 
for
 
a

  very   short   period.
In
 
all
 
cases,
 
it
 
is
 
essential
 
to
 
remove
 
the
 
key
 
from
 
the
 
ignition
 
switch
 
when
 
leaving

  the   vehicle.
Anti-theft protection
Do not make  any  modifications  to  the  electronic  engine  immobiliser  system;  this
  could   cause   malfunctions.
When purchasing a second-hand vehicle
Have the pairing  of  all  of  the  keys  in  your  possession  checked  by  a  CITROËN
 dealer ,  to  ensure  that  only  your  keys  can  be  used  to  open  and  
start

  the   vehicle.
4
ACCESS

72 
C4-2_en_Chap04_ouvertures_ed01-2014
CENTRAL LOCKING CONTROL
Locking
F
 
Press
  this   button   to   lock   the   vehicle.
The
 
red
 
indicator
 
lamp
 
in
 
the
 
button
 
comes

  on. If
 
the
 
vehicle
 
is
 
locked
 
from
 
the
 
outside,

  this   button   is   inactive.
F  
In
 
this
 
case,
 
use
 
the
 
remote
 
control

 
or
 
the
 
key
 
to
 
unlock
 
the vehicle or pull an interior
door

  handle   to   open   a   door.
If  
one
 
of
 
the
 
doors
 
is
 
open,
 
cen
-
tral
 
locking
 
from
 
the
 
inside
 
does
 
not

  take   place. Unlocking
F
 
Press
 
the
 
button
 
again
 
to
 
unlock
 
the
 
vehicle.
The
 
red
 
indicator
 
lamp
 
in
 
the
 
button
 
goes

  off.
ANTI-INTRUSION SECURITY
Operation
If
 
one
 
of
 
the
 
doors
 
or
 
the
 
boot
 
is
 
open,
 
the

 
automatic
 
central
 
locking
 
does
 
not
 
take

  place.
This
 
control

 
allows

 
the

 
simultaneous

 
locking

 
or

 
unlocking

 
of

 
the

 
doors

 
and

 
boot

 
from
 
inside
 
the
 
vehicle.
This 
system
 
allows
 
automatic
 
simulta
-
neous  
locking
 
of
 
the
 
doors
 
and
 
boot
 
as
 
soon

 
as
 
the
 
speed
 
of
 
the
 
vehicle
 
ex
-
ceeds   6   mph   (10   km/h).
Carrying long and voluminous
objects
If you  want  to  drive  with  the  boot open,
 you  should  press  the  central locking

 
button
 
to
 
lock
 
the
 
the
 
doors. Otherwise,

 
every
 
time
 
the
 
speed of

 
the
 
vehicle
 
exceeds
 
6
 
mph 
(10

 
km/h),
 
the
 
locks
 
will
 
rebound and

 
the
 
alerts
 
mentioned
 
above
 
will appear

.
Pressing the  central  locking  button  un -
locks   the   vehicle.
Above
 
6
 
mph
 
(10
 
km/h),
 
this
 
locking
 
is
 
temporary

.
This is signalled  by  the  sound  of  the locks
 rebounding,  accompanied  by  il -
lumination
 
of
 
this
 
symbol
 
in
 
the
 
instru
-
ment
 
panel,
 
an
 
audible
 
signal
 
and
 
the display

  of   an   alert   message.
4
ACCESS

73 
C4-2_en_Chap04_ouvertures_ed01-2014
Emergency control
System allowing the  doors  to  be  locked  and
 unlocked  manually  in  the  event  of  
a

 
malfunction
 
of
 
the
 
central
 
locking
 
sys
-
tem
  or   battery   failure.
Locking the driver's door
F
 
Insert
 
the
 
key
 
in
 
the
 
door
 
lock,
 
then
 
turn

  it   to   the   rear.
You
 
can
 
also
 
apply
 
the
 
procedure
 
de
-
scribed
  for   the   passenger   doors.
Unlocking the driver's door
F
 
Insert
 
the
 
key
 
in
 
the
 
door
 
lock,
 
then
 
turn

  it   to   the   front. Locking the front and rear
passenger doors
Unlocking the front and rear
passenger doors
F
 
Pull
 
the
 
interior
 
door
 
opening
 
control.
F

 
Open
  the   doors.
F
 
On
 
the
 
rear
 
doors,
 
check
 
that
 
the
 
child

 
lock
 
is
 
not
 
on
 
(see
 
the
 
corre
-
sponding
  section).
F
 
Remove
 
the
 
black
 
cap,
 
located
 
on
 
the

  edge   of   the   door,   using   the   key.
F
 
Insert
 
the
 
key
 
in
 
the
 
socket
 
without
 
forcing

 
it,
 
then
 
without
 
turning
 
it,
 
move

 
the
 
latch
 
sideways
 
towards
 
the

  inside   of   the   door.
F
 
Remove
  the   key   and   refit   the   cap.
F
 
Close
 
the
 
doors
 
and
 
check
 
that
 
the
 
vehicle

 
has
 
locked
 
correctly
 
from
 
the

  outside.
Activation / Deactivation
You
 
can

 
activate

 
or

 
deactivate

 
this

 
func

-
tion
 
permanently.
F
 
With

 
the

 
ignition

 
on,

 
press

 
this

 
but

-
ton
 
until

 
an

 
audible

 
signal

 
starts

 
and

 
a

 
corresponding

 
message

 
is

 
dis

-
played.
the
 
state

 
of

 
the

 
system

 
stays

 
in

 
memory

 
when

 
switching
 
off
 
the
 
ignition.
4
ACCESS

74 
C4-2_en_Chap04_ouvertures_ed01-2014
* According  to   country.
ALARM*
System which protects  and  provides  a deterrent
 against  theft  and  break-ins.  It provides

 
the
 
following
 
types
 
of
 
monitoring.
-


exterior perimeter
The

 
system
 
checks
 
for
 
opening
 
of
 
the
 
vehicle.
The

 
alarm
 
is
 
triggered
 
if
 
anyone
 
tries
 
to
 
open

  a   door,   the   boot,   the   bonnet...
-

interior volumetric
The

 
system
 
checks
 
for
 
any
 
variation
 
in
 
the volume

  in   the   passenger   compartment.
The
 
alarm
 
is
 
triggered
 
if
 
anyone
 
breaks
 
a window

,  
enters
 
the
 
passenger
 
compart
-
ment
  or   moves   inside   the   vehicle.
-
tilt
The
 
system
 
checks
 
for
 
any
 
change
 
in
 
the

  attitude   of   the   vehicle.
The
 
alarm
 
is
 
triggered
 
if
 
the
 
vehicle
 
is
 
lifted,

  moved   or   knocked.
Self-protection function
The
 
system
 
checks
 
for
 
the
 
putting
 
out
 
of

  service   of   its   components.
The
 
alarm
 
is
 
triggered
 
if
 
the
 
battery
,  
the
 
central

 
control
 
or
 
the
 
siren
 
wiring
 
are
 
put

  out   of   service   or   damaged.
For
 
all
 
work
 
on
 
the
 
alarm
 
sys
-
tem,
 
contact
 
a
 
CITROËN
 
dealer
 
or

  a   qualified   workshop.
Locking the vehicle with full
alarm system
Activation
F 
Switch
 
of
f  
the
 
ignition
 
and
 
get
 
out
 
of
 
the

  vehicle.
F
 
Press
 
the
 
locking
 
button
 
on
 
the
 
re
-
mote
  control.
The
 
monitoring
 
system
 
is
 
active:
 
the
 
in
-
dicator
 
lamp
 
in
 
the
 
button
 
flashes
 
once
 
per

  second.
After
 
the
 
locking
 
button
 
on
 
the
 
remote
 
control

 
is
 
pressed,
 
the
 
exterior
 
perime
-
ter
 
monitoring
 
is
 
activated
 
after
 
a
 
delay
 
of

 
5
 
seconds
 
and
 
the
 
interior
 
volumetric
 
and

 
anti-tilt
 
monitoring
 
after
 
a
 
delay
 
of
 
45

  seconds. If
 
an
 
opening
 
(door
,  
boot...)
 
is
 
not

 
closed
 
fully
,  
the
 
vehicle
 
is
 
not
 
locked

 
but
 
the
 
exterior
 
perimeter
 
monitoring

 
will
 
be
 
activated
 
af
-
ter  
a
 
delay
 
of
 
45
 
seconds
 
at
 
the
 
same

 
time
 
as
 
the
 
interior
 
volu
-
metric   and   anti-tilt   monitoring.
Deactivation
F  
Press
 
the
 
unlocking
 
button
 
on
 
the
 
remote

  control.
The
 
alarm
 
system
 
is
 
deactivated:
 
the
 
indicator

  lamp   in   the   button   goes   off.
4
ACCESS

75 
C4-2_en_Chap04_ouvertures_ed01-2014
Operating fault
When the ignition  is  switched  on,  fixed illumination
 of  the  indicator  lamp  in  the button

  indicates   a   fault   with   the   system.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

  a   qualified   workshop.
Locking the vehicle with exterior
perimeter monitoring only
Deactivate the  interior  volumetric  and  anti-tilt
 monitoring  to  avoid  unwanted  
triggering

 
of
 
the
 
alarm
 
in
 
certain
 
cases
 
such

  as:
-
 
leaving
  a   pet   in   the   vehicle,
-
 
leaving
  a   window   partially   open,
-
 
washing
  your   vehicle,
-
 
changing
  a   wheel,
-
 
having
  your   vehicle   towed,
-
 
transport
  by   sea.
Deactivation of the interior
volumetric and anti-tilt monitoring
F
 
Switch
  off   the   ignition.
F
 
Within
 
ten
 
seconds,
 
press
 
the
 
but
-
ton
 
until
 
the
 
indicator
 
lamp
 
is
 
on
 
continuously

.
F
 
Get
  out   of   the   vehicle.
F
 
Press
 
the
 
locking
 
button
 
on
 
the
 
re
-
mote
  control   immediately. The
 
exterior
 
perimeter
 
monitoring
 
alone
 
is

 
activated:
 
the
 
indicator
 
lamp
 
in
 
the
 button
  flashes   once   per   second.
To  
be
 
ef
fective,  
this
 
deactivation
 
must

 
be
 
carried
 
out
 
each
 
time
 
the

  ignition   is   switched   off.
Reactivation of the interior
volumetric and anti-tilt monitoring
F
 
Press
 
the
 
unlocking
 
button
 
on
 
the
 
remote

 
control
 
to
 
deactivate
 
the
 
ex
-
terior
  perimeter   monitoring.
F
 
Press
 
the
 
locking
 
button
 
on
 
the
 
re
-
mote
 
control
 
to
 
activate
 
all
 
the
 
moni
-
toring
  functions.
The
 
indicator
 
lamp
 
in
 
the
 
button
 
again
 
flashes

  once   per   second.
Triggering of the alarm
This is indicated  by  sounding  of  the  si -
ren  and  flashing  of  the  direction  indica -
tors
  for   thirty   seconds.
The
 
monitoring
 
functions
 
remain
 
ac
-
tive
 
until
 
the
 
alarm
 
has
 
been
 
triggered
 
eleven

  times   in   succession.
When
 
the
 
vehicle
 
is
 
unlocked
 
using
 
the
 
remote

 
control,
 
rapid
 
flashing
 
of
 
the
 
in
-
dicator
 
lamp
 
in
 
the
 
button
 
informs
 
you
 
that

 
the
 
alarm
 
was
 
triggered
 
during
 
your
 
absence.

 
When
 
the
 
ignition
 
is
 
switched
 
on,

  this   flashing   stops   immediately.
Failure of the remote control
To deactivate the monitoring functions:
F  
unlock
 
the
 
vehicle
 
using
 
the
 
key
 
in
 
the

  driver's   door   lock,
F
 
open
 
the
 
door;
 
the
 
alarm
 
is
 
triggered,
F

 
switch
 
on
 
the
 
ignition;
 
the
 
alarm stops;

 
the
 
indicator
 
lamp
 
in
 
the
 
button goes

  off.
Locking the vehicle without
activating the alarm
F Lock or  deadlock  the  vehicle  using  the
  key   in   the   driver's   door   lock.
4
ACCESS

76 
C4-2_en_Chap04_ouvertures_ed01-2014
DOORS
Opening
F After unlocking  the  vehicle  com -
pletely  using  the  remote  control  or  
the

  key,   pull   the   door   handle.
From outside
When  
the
 
selective
 
unlocking
 
is
 
activated,

 
the
 
first
 
press
 
of
 
the
 
remote

 
control
 
unlocking
 
button
 
permits

 
unlocking
 
of
 
the
 
driver's
 
door

  only. F

Pull the
interior control lever of a
front  
door;
 
this
 
unlocks
 
the
 
vehicle
 
completely

.
From inside
With  
the
 
selective
 
unlocking
 
ac
-
tivated:
-
 
opening
 
the
 
the
 
driver's
 
door
 
unlocks

 
the
 
driver's
 
door
 
only
 
(if

 
the
 
vehicle
 
has
 
not
 
already
 
been

  completely   unlocked).
-
 
opening
 
one
 
of
 
the
 
passen
-
ger
 
doors
 
unlocks
 
the
 
rest
 
of
 
the

  vehicle.
Closing
When a door is not closed correctly:
-  
when the engine is run
-
ning,
 
this
 
warning
 
lamp
 
comes

 
on,
 
accompanied
 
by
 
an

 
alert
 
message
 
for
 
a
 
few
 
seconds,
-

 
when the vehicle is moving
 
(speed
 
higher

 
than
 
6
  mph  
(10
  km/h)),  
this
 
warning

 
lamp
 
comes
 
on,
 
accom
-
panied
 
by
 
an
 
alert
 
message
 
for
 
a
 

few

  seconds.
4
ACCESS

77 
C4-2_en_Chap04_ouvertures_ed01-2014
BOOT
Opening
F After unlocking  the  boot  or  the  ve -
hicle  using  the  remote  control  or  the  
key

,  
press
 
the
 
opening
 
control,
 
then
 
raise

  the   tailgate.
Closing
F Lower the  tailgate  using  the  interior  grab
  handle.
F
 
If
 
necessary
,  
press
 
down
 
on
 
the
 
tail
-
gate
  to   fully   close   it.
Tailgate release
System allowing the  mechanical  unlock -
ing  of  the  boot  in  the  event  of  a  battery  or central

  locking   system   malfunction.
Unlocking
F
 
Fold
 
back
 
the
 
rear
 
seats
 
to
 
gain
 
access

 
to
 
the
 
lock
 
from
 
inside
 
the
 
boot.
F

 
Insert
 
a
 
small
 
screwdriver
 
into
 
hole
 
A

of
  the   lock   to   unlock   the   tailgate.
F
 
Move
  the   latch   to   the   left.
If
 
the
 
tailgate
 
is
 
not
 
closed
 
correctly:
-
 
when

the engine is running,
this
 
warning

 
lamp

 
comes

 
on, accompanied

 
by

 
the

 
display of

 
an

 
alert

 
message

 
for

 
a

 
few seconds,
-

 
when the vehicle is moving

 
(speed above

 
6

 
mph
 
(10

 
km/h)),
 
this

 
warn

-
ing
 
lamp

 
comes

 
on,

 
accompanied

 
by an

 
audible

 
signal

 
and

 
the

 
display

 
of an

 
alert
 
message
 
for
 
a
 
few
 
seconds. Locking after closing
If
 
the
 
fault
 
persists
 
after
 
closing
 
again,
 
the

  boot   will   remain   locked.
4
ACCESS

78 
C4-2_en_Chap04_ouvertures_ed01-2014
ELECTRIC WINDOWS
Fitted with a  safety  anti-pinch  system  and
 a  deactivation  system  for  the  rear  
controls.
1.


Driver's electric window
.
2.

Passenger's electric window
.
3.

Rear right electric window
.
4.

Rear left electric window
.
5.

Deactivation of the rear electric
window controls. The

 
electric
 
window
 
controls
 
remain

 
operational
 
for
 
approxi
-
mately
 
45
 
seconds
 
after
 
the
 
i

 
gnition
 
is
 
switched
 
of
f  
or
 
until
 
the

 
vehicle
 
is
 
locked
 
after
 
a
 
door
 
is

  opened.
If
 
one
 
of
 
the
 
passenger
 
windows
 
cannot

 
be
 
operated
 
from
 
the
 
driver's

 
door
 
control
 
panel,
 
carry
 
out

 
the
 
operation
 
from
 
the
 
con
-
trol
 
panel
 
of
 
the
 
passenger
 
door
 
concerned,

  and   vice   versa.
After approximately ten  consecutive complete
 opening/closing  move -
ments
 
of
 
the
 
window
,  
a
 
protection function

 
is
 
activated
 
which
 
only
 
au
-
thorises
 
closing
 
of
 
the
 
window
 
to prevent

 
damage
 
to
 
the
 
electric
 
win
-
dow
  motor.
Once
 
the
 
window
 
is
 
closed,
 
the
 
con
-
trols
 
will
 
become
 
available
 
again
 
af
-
ter
  approximately   40   minutes.
If the window  cannot  be  closed  (for
 example,  in  the  presence  of  
ice),

 
once
 
the
 
window
 
has
 
low
-
ered:
F
 
press
 
and
 
hold
 
the
 
control
 
until

  the   window   opens   fully,
F
 
then
 
pull
 
the
 
control
 
immedi
-
ately
 
and
 
hold
 
it
 
until
 
the
 
win
-
dow
  closes,
F
 
continue
 
to
 
hold
 
the
 
control
 
for

 
approximately
 
one
 
sec
-
ond
 
after
 
the
 
window
 
has
 
closed.
The

safety anti-pinch func-
tion is not operational during
these operations.
There
 
are
 
two
 
options:
-
 
manual mode
F

 
Press

 
or

 
pull

 
the

 
control

 
gently

.
 
The window

 
stops

 
when

 
the

 
control

 
is released.
-

 
automatic mode
F

 
Press

 
or

 
pull

 
the

 
control

 
firmly

.
 
The

 
window

 
opens

 
or

 
closes

 
fully

 
when

 
the
 
control
 
is
 
released.
F
 
Pressing

 
the

 
control

 
again

 
stops

 
the

 
movement
 
of
 
the
 
window.
Safety anti-pinch
When 
the
 
window
 
rises
 
and
 
meets
 
an
 
obstacle,

 
it
 
stops
 
and
 
partially
 
lowers
 
again.
One-touch electric windows
4
ACCESS

55
86 
C4-2_en_Chap05_visibilite_ed01-2014
Switching off
The 
welcome
 
lighting
 
switches
 
of
f  
au
-
tomatically
 
after
 
a
 
programmed
 
time,
 
when

 
the
 
ignition
 
is
 
switched
 
on
 
or
 
on
 
locking

  the   vehicle.
Welcome lighting
Switching onF  
Press
 
the
 
open
 
padlock
 
on
 
the

 
remote
 
control;
 
your
 
ve
-
hicle
  is   unlocked.
The
 
remote
 
switching
 
on
 
of
 
the
 
light
-
ing  
makes
 
your
 
access
 
to
 
the
 
vehicle
 
easier

 
in
 
poor
 
light.
 
It
 
is
 
activated
 
de
-
pending  
on
 
the
 
light
 
level
 
detected
 
by
 
the

  sunshine   sensor.
The  
sidelamps
 
and
 
dipped
 
beam
 
head
-
lamps,
 
as
 
well
 
as
 
the
 
side
 
spotlamps,
 
lo
-
cated
  under   the   door   mirrors,   come   on.Programming
Activation  
or
 
deactivation,
 
as
 
well

 
as
 
the
 
duration
 
of
 
the
 
light
-
ing  
duration
 
for
 
the
 
welcome
 
lighting

 
can
 
be
 
set
 
via
 
the
 
ve
-
hicle   configuration   menu.
VISIBILITY

55
93 
C4-2_en_Chap05_visibilite_ed01-2014
1. Front courtesy lamp
2.
Front map reading lamps
3.


Rear courtesy lamp
4.


Rear map reading lamps
COURTESY LAMPS
- when  the   vehicle   is   unlocked,
-  
when
 
the
 
key
 
is
 
removed
 
from
 
the
 
ignition,
-

 
on
  opening   a   door,
-
 when

 
the
 
remote
 
control
 
locking
 
but
-
ton
  is   used   to   locate   your   vehicle.
Front and rear courtesy lamps
In this position, the courtesy
lamp  comes   on   gradually:
It
 
switches
 
off   gradually:
-
 
when

 
the   vehicle   is   locked,
-
 
when

 
the   ignition   is   switched   on,
-
 
30

 
seconds  
after
 
the
 
last
 
door
 
is
 
closed. T

o  
switch
 
of
f  
the
 
rear
 
courtesy
 
lamp,
 
put
 
it

  in   the   the   "permanently   off"   position.
Permanently
  off.
Permanent
  lighting. In
 
permanent
 
lighting
 
mode,
 
the
 lighting
 time  varies  according  to  the
  circumstances:
-
 
with
 
the
 
ignition
 
of
f,  
approxi
-
mately
  ten   minutes,
-
 in

 
energy
 
economy
 
mode,
 
ap
-
proximately
  thirty   seconds,
-
 
with
 
the
 
engine
 
running,
 
un
-
limited.
When
 
the
 
courtesy
 
lamp
 
is
 
in
 
the

 
"permanent
 
lighting"
 
posi
-
tion,
 
the
 
rear
 
courtesy
 
lamp
 
also
 
comes

 
on,
 
except
 
if
 
it
 
is
 
in
 
the
 
"permanently

  off"   position.
Front and rear map reading
lamps
Take care not  to  put  anything  in  contact
  with   the   courtesy   lamps.
F
 
With
 
the
 
ignition
 
on,
 
press
 
the

  corresponding   switch.
VISIBILITY