Pil Citroen C4 PICASSO 2008 1.G Owner's Manual

III
119
A Lounge version is available in the 5 seater model. This has two se-cond-row seats that are identical to the fi rst-row seats, providing greater comfort for rear passengers.
ADJUSTING THE SEATS
The seats have the following adjust-ments :
- head-restraint adjustment,
- backrest angle,
- greater longitudinal adjustment,
- height-adjustable armrests.
Refer to the page " FRONT SEATS - Manual adjustments " for the operation of the adjustment controls.
LUGGAGE COVER BEHIND
THE SEATS
A fl exible luggage cover positio-ned behind the second-row seats enables you to prevent objects from sliding under or between the second-two seats, as well as concealing the contents of your boot from outside view.
It is fi xed to the fl oor by two hooks located behind the seats and an-chored at special points on the rear pillars.
This fl exible luggage cover is mo-vable and can be rolled up for stowage behind the second-row seats.
SEAT BELTS
For safety reasons, always attach your seat belt before positioning the armrest between yourself and the door.
STORAGE POCKETS
Two storage pockets are located on the insides of the Lounge ver-sion seats.
F E A T U R E S O F T H E 4 S E A T E R
L O U N G E V E R S I O N

122
III
Stowing the tongue of the third-row seat belt
Secure the tongue in the place provided on the rear pillar trim.Note : The third-row passenger seat belts that are not being used can be stowed in order to free up load-space and facilitate use of the luggage cover.
Requirements for the third-row passenger seat belts
Take care to attach the third-row passenger seat belts on the rings provided for this purpose.
Do not attach the belts on the anchoring points marked with a red cross (see illustration above).
T H I R D R O W S E A T B E L T S G R A N D C 4 P I C A S S O
Before use :
To avoid damaging or jamming the seat belts, take care to stow them on the sides of the backrests.

12
78
3
56
4
78
12
3
56
4
146
III
B O O T C A R G O N E T - G R A N D C 4 P I C A S S O A N D C 4 P I C A S S O
Cargo net : Grand C4 Picasso
There are 8 anchoring rings in the boot to enable you to secure your loads :
- 1 and 2 underneath the luggage-cover blind.
- 3, 4, 7 and 8 on the boot fl oor.
- 5 and 6 on the boot pillars.
Cargo net : C4 Picasso
There are 8 anchoring rings in the boot to enable you to secure your loads :
- 1, 2, 3 and 4 on the boot fl oor,
- 5, 6, 7 and 8 on the boot pillars.
The cargo net gives you a number of confi gurations depending on which of the anchoring rings you attac h it to (hammock format, vertical / horizontal, on the fl oor or behind the second row seats), enabling you to secure a variety of objects in the boot.
Note : For reasons of safety in the event of sudden braking, it is re commended that you place heavy objects on the fl oor as close as possible to the backrests of the second-row se ats.
Carrier bag hook
A carrier bag hook is available inside the boot on the left hand side.

CD
AAB
III
147
B O O TL U G G A G E C O V E R B L I N D - G R A N D C 4 P I C A S S O
Luggage-cover blind
Position 1 : (5-seat confi guration, behind the second row)
Behind the second-row seats, with the third-row seats folded away.
To install the roller :
1. Position the left-hand end of the blind roller in notch A.
2. Compress the right-hand end of the roller and place it in notch B.
3. Unroll the blind until it reaches the boot pillars.
4. Insert the guides of the blind into the rails on the pillars.
To remove the blind:
- Perform these operations in reverse order.
Note : the rollerhas a moving fl ap to avoid interference with the second-row passengers when the seats are i n the reclined position.
Position 2 : (7-seat confi guration)
Behind the third-row seats, this position conceals objects stowed in the boot from outside view.
To install the roller :
1. Roll up the blind, then remove the roller from its initial position.
2. Position the roller, with the blind pull bar upper-most, fl ap downward.
3. Fold the concertina plates in the vertical position.
4. Engage the lug on the left of the roller in notch C.
5. Pass the right-hand side above the third-row arm-rest.
6. Engage the lug in notch D.
7. Pull the seat belt(s) so that they will deploy without locking.
8. Unroll the blind and engage the guides into the rails on the pillars.
9. Lock the seat(s) in position.
10. Fold back the concertina plates, pressing them fi rmly in position.

194
VI
C H A N G I N G A W H E E L
WHEEL FOR TEMPORARY USE
If your vehicle is equipped with a spare wheel for temporary use only, when fi tting this it is normal to observe that the wheel bolts do not come to bear directly on the wheel rim.
The spare wheel is secured by the conical tapering of the wheel bolt’s shaft (see illustration).
When refi tting the original wheel, ensure that the wheel bolt contact surfaces are clean and in good condition.
WHEEL EQUIPPED WITH DEFLATION DETECTION SYSTEM
Such wheels have tyre pressure sensors. It is essential to have re-pairs carried out by a CITROËN dealer.
ANTI-THEFT BOLTS (alloy wheels)
Each wheel may be equipped with one anti-theft bolt.
To remove it :
1. Remove the protector that is covering it by means of the tool 2 (for removing the chrome covers on alloy wheels).
2. Use the anti-theft socket 9with the handle.
DIMENSION OF THE SPARE WHEEL
If your spare wheel has dimen-sions different from those of the normal vehicle wheels (identifi ed by a label), it is imperative to use the spare wheel only temporarily, to drive with caution, not to exceed 80 km/h (50 mph) and to have the tyre repaired and the normal wheel refi tted as soon as possible.
Tyre pressures
These are indicated on the label on the front left-hand door pillar (see "Vehicle Identifi cation").
The wheel bolts are specifi c to each type of wheel.
If new wheels are fi tted, check with your CITROËN dealer that the wheel bolts are compatible with the new wheels.
Note : take care to note down the code number on the head of the anti-theft bolt socket. This will enable you to obtain a replacement anti-theft socket from a CITROËN dealership.theft bolt socket. This will enable you This will
REFITTING A WHEEL
1. Position the wheel with the aid of the centring guide 3.
2. Do up the 3 bolts by hand, then remove the centring guide 3. Position the 4th bolt.
3. Pre-tighten the wheel bolts, using the wheelbrace 4.
4. Retract the jack 5 and disen-gage it.
5. Tighten the wheel bolts, using the wheelbrace 4.
6. Ensure that the tyre pressure is correct (see “Vehicle identi-fi cation”).